AS9100 Certification AS9100 Certification, specifies requirements for a quality management system to demonstrate the Contractor’s ability to consistently meet the customer requirements as well as statutory and regulatory requirements for the aerospace industry. An AS9100 Certification, is not mandatory; however, Contractors who desire to compete for work within the aerospace industry are encouraged to have AS9100 Certification, during the entire term of OASIS. The Contractor shall notify the OASIS CO, in writing, if there are any changes in the status of their AS9100 Certification, and provide the reasons for the change and copies of audits from an AS9100 Certification Body, as applicable. If only part of a Contractor’s organization is AS9100, certified, the Contractor shall make the distinction between which business units or sites and geographic locations have been certified.
Invoice Certification When and if requested by DXC, as a condition precedent to payment thereof, Supplier shall separately certify each invoice as follows: “We certify that contract deliverables listed hereon were produced in compliance with all applicable requirements of Sections 6, 7, and 12 of the Fair Labor Standards Act, as amended, and of regulations and orders of the U.S. Department of Labor issued under Section 14 thereof. We further certify that any and all additional contract deliverables will be produced in compliance with same.”
Compliance Certification From time to time the Sub-Adviser shall provide such certifications with respect to Rule 38a-1 under the 1940 Act, as are reasonably requested by the Fund or the Manager. In addition, the Sub-Adviser will, from time to time, provide a written assessment of its compliance program in conformity with current industry standards that is reasonably acceptable to the Fund to enable the Fund to fulfill its obligations under Rule 38a-1 under the 1940 Act.
Evaluation Report 20.5.4.1 The summary evaluation report shall be prepared by the Faculty Evaluation Committee and administrative evaluator(s) and shall include each evaluator’s individual rating. The summary evaluation report shall take into account the results of each of the evaluation components (Section 20.5.3) in order to arrive at an overall rating. When the committee and the administrative evaluator(s) cannot reach an agreement as to the overall rating, the report must include written explanation.
E-VERIFY CERTIFICATION Pursuant to Executive Order RP-80, Engineer certifies and ensures that for all contracts for services, Engineer shall, to the extent permitted by law, utilize the United States Department of Homeland Security’s E-Verify system during the term of this agreement to determine the eligibility of:
Tax Certification If Contractor is a taxable entity as defined by Chapter 171, Texas Tax Code, then Contractor certifies it is not currently delinquent in the payment of any taxes due under Chapter 171, Contractor is exempt from the payment of those taxes, or Contractor is an out‑of‑state taxable entity that is not subject to those taxes, whichever is applicable.
Inspection Reports Copies of the incident inspection reports and related documentation shall be distributed as follows:
Certification of Compliance The Owner may permit the use, prior to sampling and testing, of certain materials or assemblies when accompanied by manufacturer's certificates of compliance stating that such materials or assemblies fully comply with the requirements of the contract. The certificate shall be signed by the manufacturer. Each lot of such materials or assemblies delivered to the work must be accompanied by a certificate of compliance in which the lot is clearly identified. Materials or assemblies used on the basis of certificates of compliance may be sampled and tested at any time and if found not to be in conformity with contract requirements will be subject to rejection whether in place or not. The form and distribution of certificates of compliance shall be as approved by the Owner. When a material or assembly is specified by "brand name or equal" and the Contractor elects to furnish the specified "brand name", the Contractor shall be required to furnish the manufacturer's certificate of compliance for each lot of such material or assembly delivered to the work. Such certificate of compliance shall clearly identify each lot delivered and shall certify as to:
Evaluation Reports Where a formal evaluation of an employee's performance is carried out, the employee shall be provided with a copy to read and review. Provision shall be made on the evaluation form for an employee to sign it. The form shall provide for the employee's signature in two (2) places, one indicating that the employee has read and accepts the evaluation, and the other indicating that the employee disagrees with the evaluation. The employee shall sign in one of the places provided within seven (7) calendar days. No employee may initiate a grievance regarding the contents of an evaluation report unless the signature indicates disagreement with the evaluation. The employee shall receive a copy of the evaluation report at the time of signing. An evaluation report shall not be changed after an employee has signed it, without the knowledge of the employee, and any such changes shall be subject to the grievance procedure.
Owner Certification During the term of this Contract, the Owner certifies that: