Bumpers Sample Clauses
The "Bumpers" clause establishes specific limits or boundaries within which certain actions or changes can occur under a contract. Typically, this clause sets maximum or minimum thresholds—such as price adjustments, delivery quantities, or timeframes—that cannot be exceeded without further negotiation or agreement. For example, it might cap annual price increases at a certain percentage or restrict the number of allowable changes to a project scope. The core function of the Bumpers clause is to provide predictability and protect both parties from unexpected or excessive variations, thereby reducing risk and ensuring contractual stability.
Bumpers. All vehicles shall be equipped with bummers on the rear.
Bumpers. To be checked and rectified if there is any defect.
Bumpers lateral protection and rear underrun devices Visual inspection. (a) Looseness or damage likely to cause injury. (b) Device obviously not in compliance with the regulations. 2/
Bumpers. A. The front bumper shall be of heavy duty steel channel, or equivalent, at least 3/16-inch thickness and not less than a 9-inch face, painted black, and shall extend around the outer edges of the fender. Bumper and bumper supports shall be of sufficient strength to permit towing or pushing by another vehicle without damage. The front bumper shall be furnished by the manufacturer.
B. The rear bumper shall be of 3/16-inch pressed steel channel, or equivalent, and shall have not less than a 9-inch face. It shall wrap around the back corners of the bus and shall extend forward at least 12 inches measured from the rearmost point of the body at the floor line.
C. The rear bumper shall be furnished by the manufacturer and shall be attached directly to the frame with the following provisions:
(1) Ease in removal;
(2) Prevent hitching to or riding on it;
(3) Braced to develop the full strength of the bumper section against side or rear impact; and
(4) Permit bus to be pushed by another vehicle without permanent distortion.
D. The rear bumper shall extend beyond the rearmost part of the body surface at least 1 inch, measured at the floor line.
E. Only bumpers approved by the Administration may be used.
F. Tow eyes or hooks must be furnished front and rear and attached so as not to project beyond the front or rear bumpers. Tow eyes or hooks attached to the frame (chassis) shall be furnished by the chassis manufacturer. (QACPS Requirement)
Bumpers. Check for proper functioning of Bumpers
Bumpers. A full perimeter aluminum bumper at base of cabinet, extending beyond all projecting cart serfaces, made with an integral rolled aluminum edge. A wrap-around vinyl bumper insert is not acceptable.
Bumpers. ▇▇▇▇▇▇▇ and exhaust system 17. condition of tires, including tread depth 18. Interior and exterior rear view mirrors
Bumpers. Front and rear bumpers must be as ordered from the OEM. ☒ Yes ☐ No
Bumpers. 6.5.1. The ends of the bumpers shall be turned in towards the external surface in order to minimize the risk of fouling. This requirement is considered to be satisfied if either the bumper is recessed or integrated within the bodywork or the end of the bumper is turned in so that it is not contactable by a 100 mm sphere and the gap between the bumper end and the surrounding bodywork does not exceed 20 mm.
6.5.2. If the line of the bumper which corresponds to the outline contour of the car vertical projection is on a rigid surface, that surface shall have a minimum radius of curvature of 5 mm at all its points lying from the contour line to 20 mm inward, and a minimum radius of curvature of 2.5 mm in all other cases. This provision applies to that part of the zone lying from the contour line to 20 mm inward which is situated between and in front (or rear in case of the rear bumper) of tangential points with the contour line of two vertical planes each forming with the longitudinal plane of symmetry of the vehicle an angle of 15° (see Fig. 1). Figure 1
6.5.3. The requirement of paragraph 6.5.2. above shall not apply to parts on or of the bumper or to bumper insets which have a projection of less than 5 mm, with special reference to joint covers and jets for headlamp washers; but the outward facing angles of such parts shall be blunted, save where such parts protrude less than 1.5 mm.
6.5.4. The requirement of paragraph 6.5.2. above does not apply to the bumper cover. The provisions of paragraph 5. of this Regulation remain applicable.
Bumpers. Promoter to produce Disney-themed bumpers to be aired in and/or out of commercials, subject to Promoter’s discretion. Disney-themed Closing Segment – Promoter to produce three (3) original fully-produced closing segments of approximately forty-five seconds (:45) each. Each said closing segment shall feature and correspond in accordance with Schedule 1. Promoter will air up to five (5) but no less than three (3) of the closing segments, as determined by Promoter (total of three (3) to five (5) spots). The Closing Segment will be presented full screen and shall not have Show credits appearing over it. Providing a courtesy credit to Disney (as approved by Disney in writing) at the conclusion of each Show. Developing, hosting and maintaining throughout the Viewer Promotion Period the ▇▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇ website (the “Website”) that shall include, among other things, an opportunity for consumers to enter the Viewer Promotion; an opportunity for consumers to opt in to receive information about Disney Destinations; an image and coded link (provided by Disney) for each ▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇, ▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇, and ▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇; and an image and coded link (provided by Disney) to the respective Disney Cruise Line, Aulani, and Adventures by Disney Vacation Planning DVD offers. Producing co-branded content (such as videos, puzzles games, opinion polls, etc.) which shall be hosted on the Website. Developing, hosting and maintaining throughout the Viewer Promotion Period a tab on the Show’s Facebook page which shall include, among other things, an opportunity for consumers to enter the Viewer Promotion; an opportunity for consumers to opt in to receive information about Disney Destinations; an image and coded link (provided by Disney) for each ▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇, ▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇, and ▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇▇.▇▇▇; and an image and coded link (provided by Disney) to the respective Disney Cruise Line, Aulani, and Adventures by Disney Vacation Planning DVD offers. Promoter shall forward to Disney (in an encrypted Excel spreadsheet) all of the contact information it collects from individuals who opt-in to receive information about Disney Destinations within three (3) weeks following the conclusion of the Promotion Period. Producing promo spots in support of the Show Giveaway Promotions and the Viewer Promotion and airing such: 20 promo spot during each of the five (5) shows the week prior to the Show Giveaway Promotion Period and such: 30 promo spot during each Show dur...