Plan Preparation. The Engineer shall prepare roadway plans, profiles and typical sections for the proposed improvements. Prior to the 30% submittal, the Engineer shall schedule a workshop to review profiles, OpenRoads 3D models (if applicable) and cross-sections with the State. The profile and cross sections must depict the 2, 5, 10, 25, 50, 100 and 500 year (if available) water surface elevations. The drawings will provide an overall view of the roadway and existing ground elevations with respect to the various storm design frequencies for the length of the project. This will enable the State to determine the most feasible proposed roadway profile. The State will approve the proposed profiles, 3D models (if applicable), and cross sections before the Engineer continues with the subsequent submittals. This scope of services and the corresponding cost proposal are based on the Engineer preparing plans to construct freeway main lanes, direct connectors, ramps, frontage roads, and cross streets at intersections. The roadway plans must consist of the types and be organized in the sequence as described in the PS&E Preparation manual.
Plan Preparation. The Engineer shall design the ITS system identified above in accordance with the STATE'S Design Standards. The Engineer shall determine the necessary number of sheets for a complete design. Examples of sheets to be provided by the Engineer include ITS design sheets which show locations of field devices with cabling and conduit runs; connectivity diagrams which explain how devices communicate with one another including networking equipment; fiber optic splicing diagrams; quantity sheets; and standard sheets. The finalized design provided by the Engineer shall include enough details for a contractor to procure and install equipment, provide power, and communications to a preferred location and bring the system to full operation. The State's Project Manager will review the list of sheets and provide recommendations to the Engineer as to any sheets that are needed or not needed. The Engineer shall provide the following:
Plan Preparation a. The Engineer shall overlay the utility design plan onto the highway design plan to show existing and proposed highway features, including highway right of way lines, proposed ROW lines and all control of access lines.
Plan Preparation. The Engineer shall prepare roadway plans, profiles and typical sections for the proposed improvements. Function Code 161: Drainage
Plan Preparation. The ENGINEER shall prepare roadway plans, profiles and typical sections for the proposed improvements. This scope of services and the corresponding cost proposal are based on the ENGINEER preparing plans for a roadway reconstruction. The following plan sheets shall be included as a minimum:
Plan Preparation. The Engineer shall prepare roadway plans, profiles and typical sections for the proposed improvements. Prior to the 30% submittal, the Engineer shall schedule a workshop to review DocuSign Envelope ID: FEE70723-A887-4BCC-92B5-33508013EFFC profiles, OpenRoads 3D models (if applicable) and cross-sections with the State. The profile and cross sections must depict the 2, 5, 10, 25, 50, 100 and 500 year (if available) water surface elevations. The drawings will provide an overall view of the roadway and existing ground elevations with respect to the various storm design frequencies for the length of the project. This will enable the State to determine the most feasible proposed roadway profile. The State will approve the proposed profiles The State will approve the proposed profiles, 3D models (if applicable), and cross sections before the Engineer continues with the subsequent submittals. This scope of services and the corresponding cost proposal are based on the Engineer preparing plans to construct freeway main lanes, direct connectors, ramps, frontage roads, and cross streets at intersections. The roadway plans must consist of the types and be organized in the sequence as described in the PS&E Preparation manual.
Plan Preparation a. Develop traffic signal layouts including wiring, notes, quantities, utility information, ROW and any applicable additional ROW requirements.
Plan Preparation a. Incorporate 50% review comments and provide pre-final design.
Plan Preparation. Xxxxx will prepare a Redevelopment Plan for the Project Area, as determined in Phase 1.5, that will include all required plan elements as outlined in the Tax Increment Allocation Redevelopment Act (Chapter 65 ILCS 5/11-74.4-1, et seq.) of the Illinois Statutes as amended. Highlights of the Redevelopment Plan’s elements will include: • Project Area boundary description, and corresponding maps and related exhibits; • Redevelopment Plan and Program goals and objectives; • Proposed Project Area land use plan, infrastructure, and public improvements; • Examination of key redevelopment sites within the Project Area; and • Proposed TIF Budget based on projected incremental revenue through the life of the TIF.
Plan Preparation. The Engineer shall prepare roadway plans, profiles and typical sections for the proposed improvements. Prior to the 30% submittal the Engineer shall schedule a workshop to review profiles and cross-sections with the State. The profile and cross sections shall depict the 2, 5, 10, 25, 50, 100 and 500 year (if available) water surface elevations. The drawings will provide an overall view of the roadway and existing ground elevations with respect to the various storm design frequencies for the length of the project. This will enable the State to determine the most feasible proposed roadway profile. The State will approve the proposed profiles and cross sections before the Engineer continues with the subsequent submittals. This scope of services DocuSign Envelope ID: ED57FAE2-481A-4535-A126-CE7F0E526760 and the corresponding cost proposal are based on the Engineer preparing plans to construct freeway main lanes, direct connectors, ramps, frontage roads, and cross streets at intersections. The roadway plans shall consist of the types and be organized in the sequence as described in the PS&E Preparation manual.
