Units of Measurement. In all correspondence, in all technical schedules, on all drawings and for all instrument scales, SI units of measurement are to be employed. On drawings where IEC or other units have been used it will be in order if the equivalent SI measurement is suitably marked in addition.
Units of Measurement. Unless a provision of this Agreement expressly requires otherwise, all technical data and information contained in this Agreement or in any document relating to or arising out of this Agreement shall be interpreted and expressed in a manner consistent with the International System of Units (Systeme International d'Unites) (8th edition, 2006).
Units of Measurement. All measurements and calculations shall be in the metric system and calculations done to 4 decimal places, with the 5th digit of 5 or above being rounded up and below being rounded down.
Units of Measurement. The unit of volume for measurement of Fresh Water and Waste Water hereunder shall be one Barrel. Delivery rates for Fresh Water shall be stated in Barrels per minute.
Units of Measurement. For the purposes of this Agreement, Steam shall be measured in K lbs. of steam mass.
Units of Measurement. The following units of measurement apply to certain Products. per adapter: A license is required for each installation of an adapter that interfaces with the Product. per agent: A license is required for each unit of software with the official name of Remote Sys Call Daemon or RSCD Agent that can be deployed on a physical or virtual operating system.
Units of Measurement. 1.2.2.1 The following units of measurement a are applicable in ADR: Measurement of SI Unit b Acceptable alternative unit Relationship between units Length m (metre) - - Area m2 (square metre) - - Volume m3 (cubic metre) l c (litre) 1 l = 10-3 m3 Time s (second) min (minute) 1 min = 60 s h (hour) 1 h = 3 600 s d (day) 1 d = 86 400 s Mass kg (kilogram) g (gram) 1g = 10-3 kg t (ton) 1 t = 103 kg Mass density kg/m3 kg/l 1 kg/l = 103 kg/m3 Temperature K (xxxxxx) °C (degree Celsius) 0 °C = 273.15 K Temperature difference K (xxxxxx) °C (degree Celsius) 1 °C = 1 K Force N (xxxxxx) - 1 N = 1 kg.m/s2 Pressure Pa (pascal) 1 Pa = 1 N/m2 bar (bar) 1 bar = 105 Pa Stress N/m2 N/mm2 1 N/mm2 = 1 MPa Work kWh (kilowatt hours) 1 kWh = 3.6 MJ Energy J (joule) 1 J = 1 N.m = 1 W.s Quantity of heat eV (electronvolt) 1 eV = 0.1602 Η 10-18J Power W (watt) - 1 W = 1 J/s = 1 N.m/s Kinematic viscosity m2/s mm2/s 1 mm2/s = 10-6 m2/s Dynamic viscosity Activity Pa.s Bq (xxxxxxxxx) mPa.s 1 mPa.s = 10-3 Pa.s Dose equivalent Sv (xxxxxxx) a The following round figures are applicable for the conversion of the units hitherto used into SI Units.
Units of Measurement. The units of measurement within the AIE package submittal shall be consistent with the requirements of the Technical Data Package (TDP).
Units of Measurement. Unless specifically stated to the contrary, the units of measurement to be used throughout the Contract shall be based on the SI. System Abbreviations, whether singular or plural, shall be as follows: Kilometre km Metre m Millimetre mm Hectare ha Square meter m2 Cubic metre m3 Litre l Millilitre xx Xxxxx t Kilogram kg Gram g
Units of Measurement. The Contractor shall design in metric units. Contract drawings produced specifically for this Contract and plant manuals shall be in metric units. The marking and Test Specification of safe working load values on lifting equipment shall be in metric units.
