Vehicle measuring attitude definition

Vehicle measuring attitude means the position of the vehicle as defined by the co-ordinates of fiducial marks in the three-dimensional reference system.
Sample 1Sample 2Sample 3
Vehicle measuring attitude means the position of the vehicle as defined by the coordinates of fiducial marks in the three-dimensional reference system.
Sample 1Sample 2Sample 3
Vehicle measuring attitude means the position of the vehicle body as defined by the coordinates of at least three fiducial marks; sufficiently separated in the longitudinal (X), transverse (Y) and vertical (Z) axes of the vehicle reference coordinate system, to enable accurate alignment with the measurement axes of a coordinate measurement machine. The vehicle measuring attitude is established by positioning the test vehicle, on a level
Sample 1Sample 2Sample 3

Examples of Vehicle measuring attitude in a sentence

  • For other seats, the centre plane of the occupant is specified by the manufacturer; 2.4. "Three-dimensional reference system" means a system as described in Annex 10; 2.5. "Fiducial marks" are physical points (holes, surfaces, marks or indentations) on the vehicle body as defined by the manufacturer; 2.6. "Vehicle measuring attitude" means the position of the vehicle as defined by the coordinates of fiducial marks in the three-dimensional reference system.


More Definitions of Vehicle measuring attitude

Vehicle measuring attitude means the position of the vehicle body as defined by the coordinates of at least three fiducial marks; sufficiently separated in the longitudinal (X), transverse (Y) and vertical (Z) axes of the vehicle reference coordinate system, to enable accurate alignment with the measurement axes of a coordinate measurement machine. The vehicle measuring attitude is established by positioning the test vehicle, on a level surface; and adjusting the attitude of the test vehicle such that the vehicle longitudinal centre plane is parallel to the vertical longitudinal zero plane and the front left and right door sill pitch angles satisfy the vehicle test attitude requirements of paragraph 4.5. of Annex 1.
Sample 1
Vehicle measuring attitude means the position of the vehicle as defined by the co-ordinates of fiducial marks in the
Sample 1
Vehicle measuring attitude means the position of the vehicle as defined by the coordinates of fiducial marks in the three-dimensional reference system. REQUIREMENTSData protection For each seating position where reference data are required in order to demonstrate compliance with the provisions of the present Regulation, all or an appropriate selection of the following data shall be presented in the form indicated in appendix 3 to this annex: 3.1.1. the coordinates of the “R” point relative to the three-dimensional reference system; the design torso angle; all indications necessary to adjust the seat (if it is adjustable) to the measuring position set out in paragraph 4.3. below.3.2. Relationship between measured data and design specifications The coordinates of the “H” point and the value of the actual torso angle obtained by the procedure set out in paragraph 4. below shall be compared, respectively, with the coordinates of the “R” point and the value of the design torso angle indicated by the vehicle manufacturer. The relative positions of the “R” point and the “H” point and the relationship between the design torso angle and the actual torso angle shall be considered satisfactory for the seating position in question if the “H” point, as defined by its coordinates, lies within a square of 50 mm side length with horizontal and vertical sides whose diagonals intersect at the “R” point, and if the actual torso angle is within 5° of the design torso angle. If these conditions are met, the “R” point and the design torso angle, shall be used to demonstrate compliance with the provisions of this Regulation. If the “H” point or the actual torso angle does not satisfy the requirements of paragraph 3.2.2. above, the “H” point and the actual torso angle shall be determined twice more (three times in all). If the results of two of these three operations satisfy the requirements, the conditions of paragraph 3.2.2. above shall apply. If the results of at least two of the three operations described in paragraph 3.2.4. above do not satisfy the requirements of paragraph 3.2.2. above, or if the verification cannot take place because the vehicle manufacturer has failed to supply information regarding the position of the “R” point or regarding the design torso angle, the centroid of the three measured points or the average of the three measured angles shall be used and be regarded as applicable in all cases where the “R” point or the design torso angle is referred to in this Regulation. PROCEDURE FOR...
Sample 1

Related to Vehicle measuring attitude

  • Extreme performance coating means coatings designed for harsh exposure or extreme environmental conditions.

  • Net Metering Net metering refers to customers who sell electricity they produce, typically through a rooftop solar panel, back to the utility for credit. If you are a net metering customer, you should not enroll with XOOM because your net metering agreement will not transfer to XOOM once you enroll.

  • Continuous parameter monitoring system or "CPMS" means all of the equipment necessary to meet the data acquisition and availability requirements of this article, to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and to record average operational parameter value(s) on a continuous basis.

  • Check Meter means the Buyer revenue-quality meter section or meter(s), which Buyer may require at its discretion, as set forth in Section 3.08(b) and will include those devices normally supplied by Buyer or Seller under the applicable utility Electric Service Requirements.

  • Supportive measures means individualized services that are offered to the complainant or the respondent designed to restore or preserve equal access to the District’s education program or activity without unreasonably burdening the other party. The supportive measures must be non-disciplinary and non-punitive in nature; offered before or after the filing of a formal complaint or where no formal complaint has been filed; and offered to either party as appropriate, as reasonably available, and without fee or charge. Examples of supportive measures include, but are not limited to: measures designed to protect the safety of all parties or the District’s educational environment, or deter sexual harassment; counseling; extensions of deadlines or other course-related adjustments; modifications of work or class schedules; campus escort services; mutual restrictions on contact between the parties; changes in work or class locations; leaves of absence; and increased security and monitoring of certain areas of the campus.

  • Net meter means an appropriate energy meter capable of recording both import & export of electricity or a pair of meters one each for recording the import and export of electricity as the case may be;

  • 2 Wire Analog Voice Grade Loop or “Analog 2W” provides an effective 2-wire channel with 2-wire interfaces at each end that is suitable for the transport of analog Voice Grade (nominal 300 to 3000 Hz) signals and loop-start signaling. This Loop type is more fully described in Verizon Technical Reference (TR)-72565, as revised from time-to-time. If “Customer-Specified Signaling” is requested, the Loop will operate with one of the following signaling types that may be specified when the Loop is ordered: loop-start, ground-start, loop- reverse-battery, and no signaling. Customer specified signaling is more fully described in Verizon TR-72570, as revised from time-to- time. Verizon will not build new facilities.

  • Gross vehicle weight means the weight of a vehicle without load plus the weight of any load on the

  • Inclement Weather means any weather condition that delays the scheduled arrival or departure of a Common Carrier.

  • Diameter at breast height (dbh) means the diameter of a tree at 4 1/2 feet above the ground measured from the uphill side.

  • Predictive emissions monitoring system or "PEMS" means all of the equipment necessary to monitor process and control device operational parameters (for example, control device secondary voltages and electric currents) and other information (for example, gas flow rate, O2 or CO2 concentrations), and calculate and record the mass emissions rate (for example, pounds per hour) on a continuous basis.

  • Continuous emissions monitoring system or “CEMS” means all of the equipment that may be required to meet the data acquisition and availability requirements of this chapter, to sample, to condition (if applicable), to analyze, and to provide a record of emissions on a continuous basis.

  • Continuous monitoring system means the total equipment, required under the emission monitoring section in applicable subsections used to sample and condition (if applicable), to analyze, and to provide a permanent record of emissions or process parameters.