Type Design definition

Type Design means the drawings and specifications necessary to define the product shown to comply with the airworthiness standards, information on dimensions, materials, and processes necessary to define the structural strength of the product; and the Airworthiness Limitations section of the Instructions for Continued Airworthiness (ICA).
Sample 1Sample 2Sample 3
Type Design means the set of data and information necessary to define an aircraft, engine or propeller type for the purpose of airworthiness determination which includes:
Sample 1Sample 2Sample 3
Type Design means the description of all characteristics of a civil aeronautical product, including its design, manufacture, limitations and continuing airworthiness instructions, which determine its airworthiness.
Sample 1Sample 2

Examples of Type Design in a sentence

  • Note: For 75 minutes or less ETOPS approval, additional analysis to show compliance with paragraph 8.b will not be required for airframe systems, where for basic (non ETOPS) Type Design Approval (TDA), compliance with CS 25.1309, or its equivalent, has already been shown.

  • That materials and processes adequately conform to the specifications for the proposed Type Design.

  • Where Operational Suitability Data (OSD) is available for the Air System, the application for a MTC or changes in Type Design should include, or be supplemented after the initial application by, an assessment of the implications on the OSD resulting from military operation.

  • Where the MAA has previously approved a Specification(s) to support certification of the Air System (or sub-system changes), it may be appropriate to use the same Specification(s) to identify Airworthiness Requirements for changes to Type Design.

  • In-Service changes to the Air System Type Design should be conducted in accordance with (iaw) the classification2 and approval process in RA 58203.

  • If the Type Design evolves after the time of the inspection or test, then the final Type Design will be checked against the proposed Type Design (as it was at the time of the inspection or test), and the differences (if any) analyzed to ensure that the inspection or test results are representative of the final configuration.

  • That the manufacturing processes, construction and assembly adequately conform to those specified in the proposed Type Design.

  • This may be achieved through the provision of individual statements for each design change or by providing collective statements for lists of approved changes (e.g. Revisions to a Type Design definition for the type as validated by the Importing Party).

  • Those parts of the Air System adequately conform to the drawings in the proposed Type Design.

  • For solicitations that are very technical in nature, a Technical Selection Committee (TEAC) may be required to evaluate the firms on a pass/fail type basis related to the technical specifications and/or statement of work.


More Definitions of Type Design

Type Design means the visual representation of the typeface generated by the Font Software, including typographic characters such as letters, numerals, ornaments, symbols or punctuation and special characters. The “Usage Agreement” is the contract for the acquisition of the respec‐ tive usage rights to the selected Font Software, which is concluded between Fontwerk and the Licensee. The Usage Agreement can be concluded both in the way of the webshop operated by Fontwerk under xxx.xxxxxxxx.xxx and in the way of individual contract negotiations.
Sample 1Sample 2Sample 3
Type Design means a set of data and information necessary to define an aircraft, RPS, [engine]engine, or propeller type for the purpose of airworthiness determination;”; (qqq) the insertion after the definition of “unknown cargo” of the following definitions:
Sample 1Sample 2Sample 3
Type Design means the description of all characteristics of a product, including its design, manufacturing processes, limitations (e.g., approved section of the airplane flight manual), and continued airworthiness instructions, which determines its airworthiness. This includes drawings and specifications necessary to define the configuration and design features (e.g., dimensions, materials, and processes) and the data substantiating that the design meets the applicable airworthiness requirements.
Sample 1Sample 2
Type Design means the description of all characteristics of a product, including its design, manufacture, limitations, and continued airworthiness airworthiness instructions which determine its airworthiness.
Sample 1
Type Design means a set of data and information necessary to define an aircraft, engine or propeller type for the purpose of airworthiness determination;”. Amendment of regulation 1.01.2 of the Regulations
Sample 1
Type Design means the set of data and information necessary to define a product for the purpose of airworthiness determination. SUBSECTION II – DESIGN APPROVAL Subpart A TYPE CERTIFICATES‌SAR-21.100 Applicability (a) Reserved (b) This Subpart specifies the procedural and airworthiness requirements for the grant of a letter of acceptance of type certificate detailing the acceptance by the DGCA of a foreign type certificate. Note : CAAS does not grant type certificates. SAR-21.105 Acceptability of foreign type certificates The following foreign type certificates may be accepted by the DGCA for the grant of a letter of acceptance of type certificate: (a) a type certificate issued by the FAA where the United States of America is the State of Design; (aa) a type certificate issued by the EASA on behalf of a State that is a member of the European Union and a State of Design; or (b) a type certificate issued in accordance with Annex 8 to the Chicago Convention by the Competent Authority of a Contracting State or such other Competent Authority as the DGCA may determine. SAR-21.110 Application An application for a letter of acceptance of type certificate shall be made in a form and manner acceptable to the DGCA and must set out the following: (a) the applicable type certification basis including the applicable airworthiness design standards specified in SAR-21.755 that the product is designed to comply with; (b) the applicable aircraft noise, aircraft CO2 emission and engine emission standards specified in SAR-21.755 that the aircraft is designed to comply with.SAR-21.115 Grant of a letter of acceptance of type certificate When an applicant has demonstrated to the satisfaction of the DGCA that: (a) the product meets the applicable type certification basis; (b) the product meets the applicable standards relating to aircraft noise, aircraft CO2 emission and engine emission; (c) no feature or characteristic of the aircraft type makes it unsafe for the intended use; the DGCA may, subject to such conditions that the DGCA deems necessary, grant to the applicant a letter of acceptance of type certificate. SAR-21.117 Acceptability of data under a mutual recognition agreement or arrangement (a) A person may use data:-
Sample 1

Related to Type Design

  • Type designation means a combination of letters and numerals assigned by the Government to a major end item, assembly or subassembly, as appropriate, to provide a convenient means of differentiating between items having the same basic name and to indicate modifications and changes thereto.

  • Universal design means the design of products, environments, programmes and services to be usable by all people, to the greatest extent possible, without the need for adaptation or specialized design. “Universal design” shall not exclude assistive devices for particular groups of persons with disabilities where this is needed.

  • Maximum design heat input means the ability of a unit to combust a stated maximum amount of fuel per hour on a steady state basis, as determined by the physical design and physical characteristics of the unit.

  • Service Component means certain enabling Software, hardware peripherals and associated documentation which may be separately provided by Symantec as an incidental part of a Service.

  • Remedial Design or “RD” shall mean those activities to be undertaken by SDs to develop final plans and specifications for the RA as stated in the SOW.

  • Type of Work means (insert the type of work you expect to supply the Agency Worker into);

  • Manufacturing Process means any process for—

  • Registered design in this Act shall mean a design for which a design registration has been granted.

  • Program Materials means the documents and information provided by the Program Administrator specifying the qualifying EEMs, technology requirements, costs and other Program requirements, which include, without limitation, program guidelines and requirements, application forms and approval letters.

  • functionality means the ability of a tenderer to provide goods or services in accordance with specifications as set out in the tender documents.

  • Development Application means the development application identified in Item 5 of Schedule 1 and includes all plans, reports models, photomontages, material boards (as amended supplemented) submitted to the consent authority before the determination of that Development Application.

  • Supplier System means the information and communications technology system used by the Supplier in performing the Services including the Software, the Equipment and related cabling (but excluding the Customer System);

  • Platform Services means the products and services that Platform Users receive from a Stripe Connect Platform, regardless of whether fees are charged (e.g., web development, customer support or hosting services).

  • Common Channel Signaling (CCS means an out-of-band, packet-switched, signaling network used to transport supervision signals, control signals, and data messages. It is a special network, fully separate from the transmission path of the public switched network. Unless otherwise agreed by the Parties, the CCS protocol used by the Parties shall be SS7.

  • Programme of work means the Programme of work submitted by the contractor and approved by the Engineer-in-charge and includes and amendment thereto made from time to time and approved by the Engineer-in-charge;

  • Upgrade means a major version upgrade of any Platform software.

  • Interoperability means the ability of a Qwest OSS Function to process seamlessly (i.e., without any manual intervention) business transactions with CLEC's OSS application, and vice versa, by means of secure exchange of transaction data models that use data fields and usage rules that can be received and processed by the other Party to achieve the intended OSS Function and related response. (See also Electronic Bonding.)