Tread depth definition

Tread depth means the depth of the principal grooves.
Sample 1Sample 2Sample 3
Tread depth means the amount of tread design on the tire. "Tread depth" includes original, retread and recap tread design and, in respect to a special mileage commercial tire, recut, regrooved and siped tread design.[PL 1993, c. 683, Pt. A, §2 (NEW); PL 1993, c. 683, Pt. B, §5 (AFF).]
Sample 1Sample 2Sample 3
Tread depth means the horizontal distance from the front to the back of a tread, excluding nosing, if any.
Sample 1Sample 2

Examples of Tread depth in a sentence

  • The greatest riser height within any flight of stairs shall not382 exceed the smallest by more than 3/8 inch (9.5 mm).383 R311.7.5.2 Tread depth.

  • Tread depth includes both original, retread, and recapped tread design; and in respect to special mileage commercial tire design.

  • Tread depth should not be less than 4/32” on front tires and 2/32” on the rear tires.

  • Where repair of the damaged tyre is not possible - As per scale mentioned below:Unused Tread Depth*Reimbursement % of cost of new tyre(s) and/or tube(s)>=7mm*Unused Tread depth will be measured at the centre of the tread.

  • The greatest riser height within any flight of stairs shall not exceed the smallest by more than 3/8 inch (9.5 mm).R311.7.5.2 Tread depth.

  • Tread depth - record reading Tread depth shall not be less than 4/32 inch on the steering axle and 2/32 on the rear axle measured at three different major tread grooves at the lowest point but not on a wear bar.

  • Damaged to tyre(s) and/or tubes due to external impactThe company will cover reimbursement of repair and/or replacement as per the scale given below: Where repair of the damaged tyre is possibleCost of repairWhere repair of the damaged tyre is not possible Unused Tread Depth*Reimbursement % of cost of new tyre(s) and/or tube(s)>=7mm*Unused Tread depth will be measured at the centre of the tread.

  • The response of Australian judges will assure the successful implementation of the new system, and a willingness to learn from and apply overseas (particularly New Zealand and Canadian) experience will ease the transition.• Freedom of contract: The ability of borrowers and lenders to be inventive should not be constrained.

  • The region also has the most highly developed road network and traffic infrastructure on the entire continent.

  • Tread depth must be at least 2/32 inch measured in two adjacent treads.• Door handles or equivalent must be present and in working condition.• There must be no damaged or dislocated parts projecting from the vehicle that could present a safety hazard.• Horn must be in operating condition.• Muffler must effectively reduce sound of engine exhaust.


More Definitions of Tread depth

Tread depth. Tread depth" means the depth of the principal grooves.
Sample 1

Related to Tread depth

  • Demarcation Point means the point where Qwest owned or controlled facilities cease, and CLEC, End User Customer, premises owner or landlord ownership or control of facilities begin. "Designed, Verified and Assigned Date" or "DVA" means the date on which implementation groups are to report that all documents and materials have been received and are complete.

  • Generation Interconnection Feasibility Study means a study conducted by the Transmission Provider (in coordination with the affected Transmission Owner(s)) in accordance with Tariff, Part IV, section 36.2.

  • Interconnection Feasibility Study means either a Generation Interconnection Feasibility Study or Transmission Interconnection Feasibility Study.

  • Regional Transmission Expansion Plan means the plan prepared by the Office of the Interconnection pursuant to Operating Agreement, Schedule 6 for the enhancement and expansion of the Transmission System in order to meet the demands for firm transmission service in the PJM Region. Reliability Assurance Agreement or PJM Reliability Assurance Agreement:

  • Generator Forced Outage means an immediate reduction in output or capacity or removal from service, in whole or in part, of a generating unit by reason of an Emergency or threatened Emergency, unanticipated failure, or other cause beyond the control of the owner or operator of the facility, as specified in the relevant portions of the PJM Manuals. A reduction in output or removal from service of a generating unit in response to changes in market conditions shall not constitute a Generator Forced Outage.

  • Development Well means a well drilled inside the established limits of an oil or gas reservoir, or in close proximity to the edge of the reservoir, to the depth of a stratigraphic horizon known to be productive.

  • Test Well means a well constructed for the purpose of obtaining information needed to design a well prior to its construction. Test wells are cased and can be converted to observation or monitoring wells and under certain circumstances to production wells

  • DNS test Means one non-­‐recursive DNS query sent to a particular “IP address” (via UDP or TCP). If DNSSEC is offered in the queried DNS zone, for a query to be considered answered, the signatures must be positively verified against a corresponding DS record published in the parent zone or, if the parent is not signed, against a statically configured Trust Anchor. The answer to the query must contain the corresponding information from the Registry System, otherwise the query will be considered unanswered. A query with a “DNS resolution RTT” 5 times higher than the corresponding SLR, will be considered unanswered. The possible results to a DNS test are: a number in milliseconds corresponding to the “DNS resolution RTT” or, undefined/unanswered.

  • Depth , in respect of a building, means the measured distance between the front line of the building and the back line of the rear main wall which separates the main building from the open space;

  • NERC Interchange Distribution Calculator means the NERC mechanism that is in effect and being used to calculate the distribution of energy, over specific transmission interfaces, from energy transactions.

  • Interconnection Point means the point(s) of connection(s) at which the project is connected to the grid i.e. it shall be at 11 / 22 kV bus bar level of substation of MSEDCL.

  • Double check valve assembly means an assembly composed of two single, independently acting, check valves including tightly closing shutoff valves located at each end of the assembly and suitable connections for testing the water tightness of each check valve.