Termination Block definition

Termination Block means the equipment at the MDF where the Local Loop or Sub Loop or Jumper Wire connects;

Examples of Termination Block in a sentence

  • The higher-level processes of generation of cipher families, encryption and hashing of data streams (or data blocks for CTR, CTR-AE or CTR-HASH modes) are described in sections 3.2 to 3.6.

  • Hence, we chose a greedy algorithm based on the192 fixed-local frame and constructed a binary symmetric adjacency matrix, using the D-score metric to evaluate193 structural similarity (Fig.

  • SingTel will only use Jumper Wires conforming to CW6000 series with a nominal gauge of 0.5mm and use the proper tools for installing Jumper Wires at the Requesting Licensee’s Termination Block.

  • The Requesting Licensee shall be responsible for the installation and connection of a Tie Termination Block to access the licensed Shared Line.

  • The Requesting Licensee shall not make physical contact with or otherwise interfere, change or damage SingTel’s Building MDF, SingTel’s Outdoor Cabinet, MDF Termination Block, Termination Pin, Jumper Wires, DP, or DP Termination Pin that is used to provide the SingTel POTS.

  • The Jumper Wires shall be installed horizontally either left or right out from its starting Termination Block and then across the jumper field and vertically up or down to the destination Termination Block.

  • SingTel shall not be responsible for any damage to the Requesting Licensee’s Terminal units, Termination Block, connectors and cables caused by fire, water leakage, deterioration, mechanical ventilation failure, or anything beyond SingTel’s control in the Outdoor Cabinet Site other than to the extent that it is the result of a grossly negligent, wilful or reckless breach of this RIO Agreement by SingTel.

  • The HIV prevalence among people aged 15-49 years in Rwanda has remained stable over the last five years at 3%.

  • The Requesting Licensee shall only install the type of Termination Block specified by SingTel from time to time for terminating Subscriber Tie Cables at the Distribution Frame Mounting.

  • The Requesting Licensee shall not make physical contact with or otherwise interfere, change or damage SingTel’s MDF Termination Block, Termination Pin, cable tray or Jumper Wires.

Related to Termination Block

  • Termination, Moving You may cancel your acceptance of the Agreement with XOOM at any time prior to midnight of the thirtieth (30th) calendar day after the date of the first bill from your utility that includes XOOM charges for gas supply service without penalty or cancellation fee by calling XOOM at 0-000-000-0000 or by sending an email to xxxxxxxxxxxx@xxxxxxxxxx.xxx. When moving to an address within your local utility’s service territory, XOOM will make every effort to transfer your service to your new service address, provided that you notify XOOM within fifteen (15) days of your move. If a transfer of service is not successful or you move to a location outside your local utility’s service territory, you may cancel this Agreement at no cost to you. Failure to notify XOOM of your move will be considered a cancellation of this Agreement in accordance with its terms.

  • Network Termination Point (NTP) means the physical point at which a subscriber is provided with access to a public communications network; in the case of networks involving switching or routing, the NTP is identified by means of a specific network address, which may be linked to a subscriber number or name;

  • Termination Period means the period of time beginning with a Change in Control and ending on the earlier to occur of:

  • Automatic Termination shall have the meaning set forth in Section 2.3.2.

  • Extended Termination Date has the meaning specified in Section 2.16(c).

  • Termination Amount has the meaning set forth in Section 7.02(a).

  • Effective Termination Date has the meaning set forth in Section 10(b) hereof.

  • Stated Termination Date means December 31, 2000.

  • Termination for Cause or "Cause" shall mean termination because of the Executive's personal dishonesty, willful misconduct, any breach of fiduciary duty involving personal profit, intentional failure to perform stated duties, conviction of a felony with respect to the Bank or the Company or any material breach of this Agreement. For purposes of this Section, no act, or the failure to act, on the Executive's part shall be "willful" unless done, or omitted to be done, in bad faith and without reasonable belief that the action or omission was in the best interest of the Company or its affiliates. Any act, or failure to act, based upon authority given pursuant to a resolution duly adopted by the Board or based upon the written advice of counsel for the Company shall be conclusively presumed to be done, or omitted to be done, by the Executive in good faith and in the best interests of the Company. Notwithstanding the foregoing, the Executive shall not be deemed to have been terminated for Cause unless and until there shall have been delivered to him a Notice of Termination which shall include a copy of a resolution duly adopted by the affirmative vote of not less than three-fourths of the members of the Board at a meeting of the Board called and held for that purpose (after reasonable notice to the Executive and an opportunity for him, together with counsel, to be heard before the Board), finding that in the good faith opinion of the Board, the Executive was guilty of conduct justifying Termination for Cause and specifying the particulars thereof in detail. The Executive shall not have the right to receive compensation or other benefits for any period after Termination for Cause.

  • Agreement Termination Date is defined in Section 7.4.

  • Termination Benefit means the benefit set forth in Article 7.

  • Termination Benefits means the benefits described in Section 4.1(b).

  • Premium Termination Date With respect to the Series A Certificates, the scheduled maturity date of the Series A Certificates, with respect to the Series B Certificates, the scheduled maturity date of the Series B Certificates and with respect to the Series C Certificates, the scheduled maturity date of the Series C Certificates.

  • Reverse Termination Fee has the meaning set forth in Section 7.02(b).

  • Termination for Just Cause means termination because of Executive’s personal dishonesty, incompetence, willful misconduct, breach of fiduciary duty involving personal profit, intentional failure to perform stated duties, willful violation of any law, rule or regulation (other than traffic violations or similar offenses) or final cease-and-desist order, or material breach of any provision of this Agreement.

  • Termination for Cause" shall mean termination of the Executive's employment because of:

  • Service Termination Date means the last Day in a month upon which Service shall terminate, as set forth in a Schedule of Service and subject to any renewal thereof.

  • Termination Base Salary means that amount equal to Executive’s annual base salary with the Company at the rate in effect immediately prior to the Change of Control or, if a greater amount, Executive’s annual base salary at the rate in effect at any time thereafter.

  • Initial Termination Date has the meaning set forth in Section 8.2(a).

  • Early Termination Amount means, in respect of any Note, its principal amount or such other amount as may be specified in, or determined in accordance with, these Conditions or the relevant Final Terms;

  • Escrow Termination Date has the meaning ascribed to such term in Section 9.12.

  • Constructive Termination means:

  • Purchase Termination Date means the date upon which the Transferor shall cease, for any reason whatsoever, to make purchases of Receivables from the Seller under the Receivables Purchase Agreement or the Receivables Purchase Agreement shall terminate for any reason whatsoever.

  • Termination Payment has the meaning set forth in Section 6.03.

  • Termination for Good Reason means a Termination of Employment by Executive for a Good Reason.

  • Lease Termination Date means the last day of the Lease Term.