Temperature and humidity definition

Temperature and humidity means temperature and humidity maintained in the following ranges:
Sample 1Sample 2Sample 3

Examples of Temperature and humidity in a sentence

  • The laboratory building shall be constructed and installed with the appropriate facilities; Temperature and humidity controls shall be available wherever necessary during testing of samples.

  • Temperature and humidity controls shall be available wherever necessary during testing of samples.

  • The pharmacy shall be properly lighted and ventilated.8.5(6) Temperature and humidity.

  • Temperature (and humidity, if necessary) in the storage shall be recorded, and the storage items shall be regularly checked, when abnormalities are detected, corrective action shall be immediately performed.

  • Summary‌The International Secretariat’s assessment is that Norway has made “inadequate progress” in meeting the initial criteria for implementing Requirement 2.5 on beneficial ownership.

  • Temperature and humidity changes will cause the rubber to expand or contract.

  • Temperature, and humidity requirements are on a 24-hour, 7 day-a-week basis regardless of the heat generated by normally operating communication equipment.

  • Temperature and humidity shall be maintained within the ranges required by the manufactures instructions.

  • Temperature and humidity profiles of broiler houses with experimental conventional and tunnel ventilation systems.

  • Temperature and humidity measurements on roadways and, in general, all kinds of properties and real estate, and public and private facilities, providing all the controls required for proper upkeep and maintenance thereof, or of the goods deposited or guarded therein.

Related to Temperature and humidity

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Pressure means the total load or force per unit area acting on a surface.

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Topsoil means a varying depth (up to 300 mm) of the soil profile irrespective of the fertility, appearance, structure, agricultural potential, fertility and composition of the soil;

  • Operating pressure means the pressure at which the parts of an irrigation system are designed by the manufacturer to operate.

  • Surface water means all water which is open to the atmosphere and subject to surface runoff.

  • Backpressure means a pressure (caused by a pump, elevated tank or piping, boiler, or other means) on the consumer's side of the service connection that is greater than the pressure provided by the public water system and which may cause backflow.

  • Calibration means the determination of (1) the response or reading of an instrument relative to a series of known radiation values over the range of the instrument, or (2) the strength of a source of radiation relative to a standard.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.

  • Surface waters means all waters of the state as defined in G.S. 143-212 except underground waters

  • Emission control system means the electronic engine management controller and any emission related component in the exhaust or evaporative system which supplies an input to or receives an output from this controller.

  • Noise means two times the root mean square of ten standard deviations, each calculated from the zero responses measured at a constant frequency which is a multiple of 1,0 Hz during a period of 30 seconds.

  • Radiation area means any area, accessible to individuals, in which radiation levels could result in an individual receiving a dose equivalent in excess of 0.05 mSv (0.005 rem) in 1 hour at 30 centimeters from the source of radiation or from any surface that the radiation penetrates.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Scattered radiation means ionizing radiation emitted by interaction of ionizing radiation with matter, the interaction being accompanied by a change in direction of the radiation. Scattered primary radiation means that scattered radiation which has been deviated in direction only by materials irradiated by the useful beam.

  • Recalibration means the adjustment of all DRG weights to reflect changes in relative resource consumption.

  • Greenhouse gases (GHGs) means the aggregate group of six greenhouse gases: carbon dioxide, nitrous oxide, methane, hydrofluorocarbons, perfluorocarbons, and sulfur hexafluoride.

  • Turbidity means the cloudy condition of water due to the presence of extremely fine particulate materials in suspension that interfere with the passage of light.