Inspection Component definition

Inspection Component means any final inspection, testing or supervision required pursuant to section 221ZH of the Building Xxx 0000, as part of the plumbing work performed, as defined under the Building Xxx 0000, at no additional cost to the Customer; “PPSA” means the Personal Property Securities Xxx 0000 (Cth); “Price” means the amount payable to the Contractor for the Works; “Services” means all services supplied or to be supplied by the Contractor to the Customer; The Services include the Inspection Component; “Site” means the place or places where the Goods and Services will be supplied; “Terms” means these terms and conditions; “Works” means the Goods and Services or any combination of them, supplied or to be supplied by the Contractor to the Customer or at their request, as the case may require.
Sample 1Sample 2Sample 3

Examples of Inspection Component in a sentence

  • The building thermal envelope shall be durably sealed to limit infiltration with compliance demonstrated and documented with either a visual inspection using the attached Air Barrier and Insulation Inspection Component Criteria Checklist completed by a code official or a responsible party independent from the installer of the insulation or with a blower door infiltration test.

  • The Department will use calendar years for annual use of force training.In response to commentary in the Monitor’s Third Report, the Department has developed and proposed a review team, the Quality Inspection Component (QIC), in order to reduce the amount of time it takes for an investigative report to be reviewed and approved.

  • Inspection Component Failures Chart 2 illustrates the number of crashes in which the failure of a safety component played a role in a vehicle crash.

  • Table 450.16 - Department Acceptance Inspection of HMA Lots Inspection Component 450.74 Acceptance Sampling & Testing.

  • Additionally, perfumes and other fragrance producing products may not be used within the school building.

  • Table 450.8a - Minimum QC Inspection at HMA Production Facility Inspection Component (1) The initial temperature measurements shall be taken from the first or second load.‌(2) As a minimum, the air temperature measurements and precipitation forecast shall obtained prior to starting the HMA Plant operation.

  • Table 450.14 - Department Acceptance Inspection of HMA Patching Inspection Component Items InspectedMinimum Inspection Frequency Point of Inspection Inspection Method MaterialsMixture Type + PG Binder Grade (Correct Type) Table 450.15 - Department Acceptance Inspection of Tack Coat Inspection Component Items InspectedMinimum Inspection Frequency Point of Inspection Inspection Method B.

  • Part VII.F of the Permit requires a Road and Facility Inspection Component; and Part VII.G of the Permit requires a Traction Abrasive and Deicer Application and Recovery Component of the SWMP.

  • Table 450.14 - Department Acceptance Inspection of HMA Patching Inspection Component Items InspectedMinimum Inspection Frequency Point of Inspection Inspection Method MaterialsMixture Type + PG Binder Grade (Correct Type) 2010 Quality Assurance Specifications for Hot Mix Asphalt Pavement Table 450.15 - Department Acceptance Inspection of Tack Coat Inspection Component Items InspectedMinimum Inspection Frequency Point of Inspection Inspection Method B.

  • It means the assumed average maintenance dose per day for a drug used for its main indication in adults.

Related to Inspection Component

  • Service Component means certain enabling Software, hardware peripherals and associated documentation which may be separately provided by Symantec as an incidental part of a Service.

  • Cannabis testing facility means an entity registered by

  • Inspections has the meaning set forth in Section 4.1.2.

  • Digital audio-visual work means a series of related images which, when shown in succession, imparts an impression of motion, together with accompanying sounds, if any.

  • Commissioning Tests means all of the procedures and tests which, in accordance with the Reasonable and Prudent Standard, and in compliance with industry guidelines, practices and standards, are:

  • Marijuana testing facility means an entity licensed to analyze and certify the safety and potency of marijuana.

  • Structural component means a component that supports non-variable forces or weights (dead loads) and variable forces or weights (live loads).

  • Digital audio-visual works which means a series of related images which, when shown in succession, impart an impression of motion, together with accompanying sounds, if any;

  • Initial Environmental Examination or “IEE” means the initial environmental examination for the Project, including any update thereto, prepared and submitted by the Borrower and cleared by ADB;

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Manufacturing Site means a location where a manufacturing

  • Operational Acceptance Tests means the tests specified in the Technical Requirements and Agreed Project Plan to be carried out to ascertain whether the System, or a specified Sub system, is able to attain the functional and performance requirements specified in the Technical Requirements and Agreed Project Plan, in accordance with the provisions of GCC Clause 27.2 (Operational Acceptance Test).

  • Commissioning test means tests applied to the Generating Facility, after completion of the construction of the Generating Facility, in order to verify that the Generating Facility may be released for Operation.

  • Original component manufacturer means an organization that designs and/or engineers a part and is entitled to any intellectual property rights to that part.

  • Development Site means any parcel or lot on which exists or which is intended for building development other than the following:

  • Maintenance Test means the maintenance test set out in Clause 12.1 (Maintenance Test).

  • Analytical x-ray equipment means equipment used for x-ray diffraction or fluorescence analysis.

  • Acceptance Testing mean the tests, reviews and other activities that are performed by or on behalf of Agency to determine whether the Deliverables meet the Acceptance Criteria or otherwise satisfy the Agency, as determined by the Agency in its sole discretion.

  • Acceptance Tests means those tests performed during the Performance Period which are intended to determine compliance of Equipment and Software with the specifications and all other Attachments incorporated herein by reference and to determine the reliability of the Equipment.

  • Manufacturing Facilities means facilities engaged in the mechanical or chemical transformation of materials or substances into new products and shall include:

  • Site Visit means a visit to the Site; and

  • Structural components means liners, leachate collection systems, final covers, run-on/run-off systems, and any other component used in the construction and operation of the MSWLF that is necessary for protection of human health and the environment.

  • Finished Lots means, Entitled Land (i) that has been legally subdivided for the construction of Housing Units, (ii) that has been graded substantially in accordance with all grading plans approved by the applicable agencies and contains level building pads (except for any fine or precise grading to be completed immediately prior to vertical construction), (iii) that has all water, sewer, electrical and other utility services for planned residences installed and stubbed to the lot behind the sidewalk, (iv) that has all storm drain, sewer, curb, gutter, sidewalk and pavement for public access constructed and installed, except for any final lift of the streets and lateral connections to Housing Units, (v) that has all property corners surveyed and marked and any required survey monumentation installed, and (vi) with respect to which all applicable development fees (including, without limitation, school and development impact fees) that are required to be paid prior to obtaining a building permit have been paid other than building permit and plan check fees. Except as otherwise expressly provided in this Agreement, the term “Finished Lot” shall not include any Land upon which the construction of a Housing Unit has commenced.

  • Testing means that element of inspection that determines the properties or elements, including functional operation of materials, equipment, or their components, by the application of established scientific principles and procedures.

  • The Works/Project means the works to be executed or done under this contract.

  • Phase I Environmental Site Assessment means a Phase I environmental property assessment of the Assets that satisfies the basic assessment requirements set forth under the current ASTM International Standard Practice for Environmental Site Assessments (Designation E1527-13) or any other visual site assessment or review of records, reports or documents.