Felling and Bucking Sample Clauses

Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Sample 1Sample 2Sample 3See All (162)
AutoNDA by SimpleDocs
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A.2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in
Sample 1Sample 2Sample 3See All (30)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Contractor may buck out cull material when necessary to produce pieces meeting Utilization Stand- ards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchanta- bility factor, whichever is stated in A2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges.‌‌
Sample 1Sample 2Sample 3See All (22)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in AT2. Con- tractor may buck out cull material when necessary to pro- duce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net Measure in percentage of gross Measure, or based on the merchantability factor, whichever is stated in AT2. If necessary to assess extent of defect, Contractor shall make sample saw cuts or wedges. BT6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting.
Sample 1Sample 2Sample 3See All (10)
Felling and Bucking. Felling shall be done to minimize breakage of Included Timber and damage to residual timber. Felling shall be done by saws or shears. Trees may not be left hanging on other trees. All hung trees or spring poles must be fell or released, dropped or pulled down to the ground the day they occur. Xxxxx Heights: Stumps shall not exceed, on the side adjacent to highest ground, the maximum height of 12 inches, unless agreed otherwise in writing by Seller or their Representative. Limbing: When necessary to minimize damage to residual stand during skidding, exposed limbs shall be cut from products prior to skidding. Such limbs may be left uncut which cannot be cut with reasonable safety. Utilization: Minimum piece for the sale is 8 feet 6inches in length and have a 9 inch small end of log and have 50% sound wood. Purchaser must insure and make every effort to meet the utilization standard. Skidding: In so far as ground conditions permit products shall not be skidded against unmarked trees or groups of pole trees or groups of reproduction, and skidders or tractors shall be equipped with winch to facilitate cableing and skidding. Landings and Skid Trails: Location of all landings, skid roads, skid trails shall be agreed upon prior to construction or use in writing. Landings and major skid trails will be flagged in prior to construction and use.
Sample 1

Related to Felling and Bucking

  • Marketing and Outreach CONTRACTOR shall identify culturally and linguistically appropriate measures for reaching older adults in need of transportation and determine procedures for implementation of outreach, which may include, but is not limited to, brochures, flyers, and public presentations. In order to ensure effective collaboration and coordination of services, a CONTRACTOR shall be required to submit drafts of all printed materials related to outreach and marketing of OoA Senior Non-Emergency Medical Transportation Fixed-Price Per Mile Program services to OoA for approval before publication and dissemination.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction.

  • Training and Promotion a. The contractor will assist in locating, qualifying, and increasing the skills of minorities and women who are applicants for employment or current employees. Such efforts should be aimed at developing full journey level status employees in the type of trade or job classification involved.

  • Training and Professional Development C. Maintain written program procedures covering these six (6) core activities. All procedures shall be consistent with the requirements of this Contract.

  • Training and Development 14.1 The parties are committed to, and acknowledge the mutual benefit to the employer and employee of planned human resource development and the provision and participation in relevant development opportunities (including accredited training).

  • METERING AND BILLING Metering requirements and billing procedures shall be set forth in the AEC rate schedule(s) applicable to the electric service account assigned to the location where the Generating Facility is connected.

  • Marketing and Promotion The School will be responsible for marketing and promoting the Sports Facilities in accordance with the agreed aims and targets. A marketing strategy will be prepared and implemented and reviewed on an annual basis.

Time is Money Join Law Insider Premium to draft better contracts faster.