Cooling capacity definition

Cooling capacity means a measure of the ability of an air conditioner to remove heat from an enclosed space, as determined using the applicable test method in Section 1604(b) or 1604(c).
Cooling capacity means the nominal tonnage of compression equipment based on 40 degrees Fahrenheit suction temperature and 105 degrees Fahrenheit condensing temperature.
Cooling capacity means the amount of cooling, in Btu/h, provided to an indoor conditioned space, determined in Section 4.1 of appendix F.

Examples of Cooling capacity in a sentence

  • Key Assumptions: • BtuH = Cooling capacity in Btu/Hour – This value comes from ARI or AHAM rating or manufacturer data.

  • Cooling capacity will fall when the air circulation inside is hindered.• Do not place the refrigerator in places subject to direct sunlight.

  • Cooling capacity of each unit shall be able to remove all the sensible heat from the MCR.

  • This approach has radical implications for a theory of representation.

  • Cooling capacity will fall when the air circulation inside is hindered.• Do not place the Freezer in places subject to directsunlight.

  • Cooling capacity of the aftercooler must be sized for the total capacity of the compressors.

  • Cooling capacity will vary depending on fluid temperature, ambient temperature, and cooling fluid.

  • Cooling Capacity Cooling capacity will vary depending on fluid temperature, ambient temperature, and cooling fluid.

  • Cooling capacity As per manufacturer’s recommendation for severe duty cycle.

  • Any represented value of the SEER, EER, HSPF, SEER2, EER2, HSPF2 or other measure of energy efficiency of an individual model/ combination for which consumers would favor higher values must be less than or equal to the output of the AEDM but no less than the standard.(3) Cooling capacity.


More Definitions of Cooling capacity

Cooling capacity. ’ means the amount
Cooling capacity. ’ means the amount of cooling, in British thermal units per hour (Btu/h), provided to a conditioned space, measured under the specified conditions and determined in section 4.1 of this appendix.
Cooling capacity. ( 製 冷 量 ) means the amount of sensible and latent heat that an air-conditioner can remove from the enclosed space, room or zone to which free delivery of conditioned air is provided in a defined period of time;
Cooling capacity. (製冷量) means the amount of sensible and latent heat
Cooling capacity means the heat load [W] that can be eliminated from the indoor air per unit hour, when the multi air conditioner is operated for cooling.

Related to Cooling capacity

  • Maximum Capacity or ‘Pmax’ means the maximum continuous active power which a power-generating module can produce, less any demand associated solely with facilitating the operation of that power-generating module and not fed into the network as specified in the connection agreement or as agreed between the relevant system operator and the power-generating facility owner;

  • New Capacity means a new Generator, a substantial addition to the capacity of an existing Generator, or the reactivation of all or a portion of a Generator that has been out of service for five years or more that commences commercial service after the effective date of this definition. For purposes of Section 23.4.5 of this Attachment H, “Offer Floor” for a Mitigated Capacity Zone Installed Capacity Supplier that is not a Special Case Resource shall mean the lesser of (i) a numerical value equal to 75% of the Mitigation Net CONE translated into a seasonally adjusted monthly UCAP value (“Mitigation Net CONE Offer Floor”), or (ii) the numerical value that is the first year value of the Unit Net CONE determined as specified in Section 23.4.5.7, translated into a seasonally adjusted monthly UCAP value using an appropriate class outage rate, (“Unit Net CONE Offer Floor”). The Offer Floor for a Mitigated Capacity Zone Installed Capacity Supplier that is a Special Case Resource shall mean a numerical value determined as specified in Section 23.4.5.7.5. The Offer Floor for Additional CRIS MW shall mean a numerical value determined as specified in Section 23.4.5.7.6. For the purposes of Section 23.4.5 of this Attachment H, “Non-Qualifying Entry Sponsors” shall mean a Transmission Owner, Public Power Entity, or any other entity with a Transmission District in the NYCA, or an agency or instrumentality of New York State or a political subdivision thereof.

  • Idle capacity means the unused capacity of partially used facilities. It is the difference between: (a) that which a facility could achieve under 100 percent operating time on a one-shift basis less operating interruptions resulting from time lost for repairs, setups, unsatisfactory materials, and other normal delays; and (b) the extent to which the facility was actually used to meet demands during the accounting period. A multi-shift basis should be used if it can be shown that this amount of usage would normally be expected for the type of facility involved.

  • Storage Capacity means any combination of space, injectability and deliverability.

  • System Capacity means the operational capacity of the System at any applicable point in time.

  • Reserved Capacity means the maximum amount of capacity and energy that the Transmission Provider agrees to transmit for the Transmission Customer over the Transmission Provider’s Transmission System between the Point(s) of Receipt and the Point(s) of Delivery under Tariff, Part II. Reserved Capacity shall be expressed in terms of whole megawatts on a sixty (60) minute interval (commencing on the clock hour) basis.

  • Committed Capacity means that portion of the Capacity that is required to meet the Capacity Entitlements of Access Holders;

  • Nameplate capacity means the maximum electrical generating output (in MWe) that a generator can sustain over a specified period of time when not restricted by seasonal or other deratings as measured in accordance with the United States Department of Energy standards.

  • Design capacity means the volume of a containment feature at a discharging facility that accommodates all permitted flows and meets all Aquifer Protection Permit conditions, including allowances for appropriate peaking and safety factors to ensure sustained, reliable operation.

  • Bid Capacity meanss capacity offered by the bidder in his Bid under invitation.

  • Project Capacity means the AC capacity of the project at the generating terminal(s) and to be contracted with MSEDCL for supply from the Solar Power Project.

  • Ramping Capability means the sustained rate of change of generator output, in megawatts per minute.

  • Contracted Capacity means the capacity (in MW AC) contracted with MSEDCL for supply by the successful bidder at the Delivery Point from the Solar Power Project.

  • Rated Capacity means the Average Daily Flow for which the Works are approved to handle;

  • Available Capacity means the capacity from the Project, expressed in whole megawatts, that is available to generate Product. [For As-Available Product facilities only]

  • Contract Capacity has the meaning set forth in Section 3.1(f).

  • Installed Capacity or 'IC’ means the summation of the name plate capacities of all the units of the generating station or the capacity of the generating station (reckoned at the generator terminals), approved by the Commission from time to time;

  • Available Flowgate Capability or “AFC” shall mean the rating of the applicable Flowgate less the projected loading across the applicable Flowgate less TRM and CBM. The firm AFC is calculated with only the appropriate Firm Transmission Service reservations (or interchange schedules) in the model, including recognition of all roll-over Transmission Service rights. Non- firm AFC is determined with appropriate firm and non-firm reservations (or interchange schedules) modeled.