Certification Basis definition

Certification Basis means a set of the applicable airworthiness and environmental requirements established by ANAC and EASA as the basis by which the type design of a civil aeronautical product, or a change to that type design was approved or accepted. The certification basis may also include Special Conditions, Findings of Equivalent Level of Safety, and Exemptions or Deviations when determined by ANAC and EASA to apply to the type design.
Sample 1Sample 2Sample 3
Certification Basis means the applicable airworthiness and environmental standards established by a CA for the purpose of certification and by a VA for the purpose of validation. The certification basis may include additional technical conditions, special conditions, equivalent level of safety findings, and exemptions or deviations when determined to apply to the type design.
Sample 1Sample 2Sample 3
Certification Basis consists of the applicable airworthiness and environmental requirements established by a Participant as the basis by which the type design of a Civil Aeronautical Product, or a change to that type design was approved or accepted. The certification basis may also include Special Conditions, Findings of Equivalent Level of Safety, and Exemptions or Deviations when determined by a Participant to apply to the type design approval. For the CAA, the certification basis may also include Operational Suitability Data (OSD) requirements.
Sample 1

Examples of Certification Basis in a sentence

  • Certification Basis: Based on 14 CFR §§ 21.115 and 21.101, and the FAA policy for significant changes in FAA Order 8110.48, this STC is a non-significant change.

  • Phase 2 – establish and agree the Type Certification Basis (TCB).

  • Equipment The basic required equipment as prescribed in the applicable airworthiness regulations (see Certification Basis) must be installed in the aircraft for certification.

  • The basic required equipment as prescribed in the applicable airworthiness regulations (see Certification Basis) must be installed in the aircraft for certification.

  • Regulation 5810(7)Compliance with the Type Certification Basis (MRP Part 21.A.20)5810(7) The TAA shall demonstrate compliance with the TCB following the means approved in the CP.

  • Unsafe is measured with respect to the overall level of safety intended by the product VA Certification Basis.

  • Regulation 5810(4)Type Certification Basis (MRP Part 21.A.15)5810(4) The OCD or TAA shall propose the TCB consisting of applicable Airworthiness Requirements and Military Certification Review Items (MCRIs) (to include special conditions and proposed ELoS), as well as proposed ‘elect to comply’ and deviations, as applicable.

  • All installations should conform to the Type Certification Basis applicable to the Air System concerned, or by agreement with the MAA, to the requirements of alternative Certification Specifications for Airworthiness.

  • The product contains design features where experience with other products in service has shown an unsafe condition might occur in that product, even though compliance with the regulations in the VA Certification Basis can be demonstrated.

  • ANSWER: Assume that the existing lift station will need to be improved.

Related to Certification Basis

  • certification body means a body, including product or quality systems certification bodies, that may be designated by one Party in accordance with this Part to conduct certification on compliance with the other Party's standards and/or specifications to meet relevant mandatory requirements;

  • Recertification means the process by which a client’s eligibility to continue to receive child care assistance benefits are determined.

  • certification mark means a mark used in connection with the goods or services of a person other than the certifier to indicate geographic origin, material, mode of manufacture, quality, accuracy, or other characteristics of the goods or services or to indicate that the work or labor on the goods or services was performed by members of a union or other organization.

  • Initial Certification As defined in Section 2.02(a) hereof.

  • Certification Date means the later of the date on which an order granting certification or authorization of a Proceeding against one or more Non-Settling Defendants is issued by a Court and the time to appeal such certification or authorization has expired without any appeal being taken, or if an appeal is taken the date of the final disposition of such appeal.

  • Certification period means the period for which an individual is certified eligible for a program.

  • Interim Certification As defined in Section 2.02.

  • Certification Regarding Venue" Terms with TIPS Members Vendor agrees that if any "Venue" provision is included in any sales agreement/contract between Vendor and a TIPS Member, that clause must provide that the "Venue" for any litigation or alternative dispute resolution is shall be in the state and county where the TIPS Member operates unless the TIPS Member expressly agrees otherwise. Any TIPS Sale Supplemental Agreement containing a "Venue" clause that conflicts with these terms is rendered void and unenforceable. If Vendor disagrees, after this solicitation legally closes and TIPS begins evaluating Vendor's file, TIPS will provide Vendor with a draft Word Document version of the Vendor Agreement and will be instructed to include all requested negotiations as redline edits for TIPS consideration. Does Vendor agree? Yes Certification Regarding "Automatic Renewal" Terms with TIPS Members Vendor agrees that no TIPS Sale may incorporate an "Automatic Renewal" clause that exceeds month to month terms with which the TIPS Member must comply. All renewal terms incorporated into a TIPS Sale Supplemental Agreement shall only be valid and enforceable when Vendor received written confirmation of acceptance of the renewal term from the TIPS Member for the specific renewal term. The purpose of this clause is to avoid a TIPS Member inadvertently renewing a Supplemental Agreement during a period in which the governing body of the TIPS Member has not properly appropriated and budgeted the funds to satisfy the Agreement renewal. Any TIPS Sale Supplemental Agreement containing an "Automatic Renewal" clause that conflicts with these terms is rendered void and unenforceable. If Vendor disagrees, after this solicitation legally closes and TIPS begins evaluating Vendor's file, TIPS will provide Vendor with a draft Word Document version of the Vendor Agreement and will be instructed to include all requested negotiations as redline edits for TIPS consideration. Does Vendor agree? Yes Certification Regarding "Indemnity" Terms with TIPS Members Texas and other jurisdictions restrict the ability of governmental entities to indemnify others. Vendor agrees that if any "Indemnity" provision which requires the TIPS Member to indemnify Vendor is included in any sales agreement/contract between Vendor and a TIPS Member, that clause must either be stricken or qualified by including that such indemnity is only permitted, "to the extent permitted by the laws and constitution of [TIPS Member's State]" unless the TIPS Member expressly agrees otherwise. Any TIPS Sale Supplemental Agreement containing an "Indemnity" clause that conflicts with these terms is rendered void and unenforceable. If Vendor disagrees, after this solicitation legally closes and TIPS begins evaluating Vendor's file, TIPS will provide Vendor with a draft Word Document version of the Vendor Agreement and will be instructed to include all requested negotiations as redline edits for TIPS consideration. Does Vendor agree? Yes Certification Regarding "Arbitration" Terms with TIPS Members Vendor agrees that if any "Arbitration" provision is included in any TIPS Sale agreement/contract between Vendor and a TIPS Member, that clause may not require that the arbitration is mandatory or binding. Vendor agrees that if any "Arbitration" provision is included in any TIPS Sale agreement/contract between Vendor and a TIPS Member, that clause provides for only voluntary and non-binding arbitration unless the TIPS Member expressly agrees otherwise. Any TIPS Sale Supplemental Agreement containing a “Arbitration” clause that conflicts with these terms is rendered void and unenforceable. If Vendor disagrees, after this solicitation legally closes and TIPS begins evaluating Vendor's file, TIPS will provide Vendor with a draft Word Document version of the Vendor Agreement and will be instructed to include all requested negotiations as redline edits for TIPS consideration. Does Vendor agree? Yes

  • Certifications shall have the meaning set forth in Section 3.4(a).

  • Certification Requirements means those requirements specified or referenced in this Agreement that you must meet in order to use and maintain the Certification Designation and use the Logo in accordance with the terms of this Agreement.

  • practising certificate means a document issued by the Relevant Professional Body entitling you to provide legal services;