Block length definition

Block length means the linear dimension of a block along one of its street frontages.
Sample 1Sample 2Sample 3
Block length means the distance between the intersection of two street ROWs, measured at the street line.
Sample 1Sample 2Sample 3
Block length means the distance between intersections of through streets, such distance being measured along the longest street bounding the block and from the right-of-way line of the two (2) intersecting streets.
Sample 1Sample 2

Examples of Block length in a sentence

  • Block length is limited to 400 feet measured from curb edge to curb edge.

  • Block length shall not be designed, unless otherwise impractical, to be more than one thousand two hundred feet (1,200’) or less than four hundred feet (400’) in length.

  • Block length is defined as the distance along a street between the centerline of two intersecting through-streets.

  • Block length is defined as the distance along a street between the centerline of two intersecting through streets.

  • Block length shall not be designed, unless otherwise impractical, to be more than 1,600 feet.

  • Block length shall be measured along the block face from intersection to intersection between the nearest two streets.

  • Block length (intersection to intersection) shall range from 300 feet - 800 feet.

  • Block length in a residential subdivision shall not exceed one thousand five hundred (1,500) feet.

  • If the Commission decides to refuse authorisation, the approval authority shall immediately give notice to the holder of the provisional type-approval referred to in paragraph 4 that the provisional approval will be revoked six months after the date of the Commission’s refusal.

  • Block length and width shall be sufficient to accommodate the size of lots required by this UDC and to provide for convenient access, circulation control and safety of street traffic.Subd.


More Definitions of Block length

Block length means the perimeter distance around a block, divided by two.
Sample 1Sample 2
Block length means the distance be- tween intersections of through streets, measured between the right-of-way lines of the intersecting streets, which distance is the longest dimension of a block.
Sample 1
Block length means the length of a block measured at the right- of-way lines and at right angles to its width. If the width and length of the block are not equal in distance, the length shall be considered to be the greater of the two.
Sample 1
Block length means the length of one side of a block (i.e. the distance between streets on opposite sides of the block).
Sample 1
Block length means the distance measured along all that part of one side of a street which is between two intersecting or intercepting streets, or between an intersecting or intercepting street and a railroad right-of-way, watercourse, body of water or unsubdivided acreage.
Sample 1

Related to Block length

  • overall length means the distance between the two vertical planes perpendicular to the median longitudinal plane of the vehicle and touching its front and rear outer edge, disregarding the projection:

  • Arm’s Length Transaction means a transaction between two related parties that is conducted as if they were unrelated, so that there is no conflict of interest.

  • Arm’s Length has the meaning ascribed to such term for the purposes of the Income Tax Act (Canada);

  • Length (L) means 96 per cent of the total length on a waterline at 85 per cent of the least moulded depth measured from the top of the keel, or the length from the foreside of the stem to the axis of the rudder stock on that waterline, if that be greater. In ships designed with a rake of keel the waterline on which this length is measured shall be parallel to the designed waterline. The length (L) shall be measured in metres.

  • Stage Length The stage length is defined as the sum of the distances for the climbout maneuver, climb, cruise, and descent.

  • Length (L) means 96 per cent of the total length on a waterline at 85 per cent of the least moulded depth measured from the top of the keel, or the length from the foreside of the stem to the axis of the rudder stock on that waterline, if that be greater. In ships designed with a rake of keel the waterline on which this length is measured shall be parallel to the designed waterline. The length (L) shall be measured in metres.

  • Permitted Affiliate Transactions means any transaction entered into between any member of the Group and the Parent or any other member of the Kronos Group either (i) in the ordinary course of trading or business and in accordance with past practice or (ii) which is necessary to accommodate legal or regulatory requirements of such member of the Group.

  • Accumulation Period Length means 12 months; provided, however, if the commencement of the Accumulation Period is delayed in accordance with Section 2.11 hereof, the Accumulation Period Length shall be determined in accordance with the definition of “Accumulation Period Length” in the Indenture Supplement.

  • Affiliate Transaction has the meaning provided in Section 4.11.

  • Affiliate Transactions has the meaning set forth in Section 4.11 (“Transactions with Affiliates”).

  • Bundled transaction means the purchase of 2 or more distinct and identifiable products, except real property and services to real property, where the products are sold for a single nonitemized price. A bundled transaction does not include the sale of any products in which the sales price varies, or is negotiable, based on the selection by the purchaser of the products included in the transaction. As used in this subdivision:

  • Arm s length transaction” means a transaction between two related parties that is conducted as if they were unrelated, so that there is no conflict of interest.

  • Replacement Transaction means, with respect to any Terminated Transaction or group of Terminated Transactions, a transaction or group of transactions that (i) would have the effect of preserving for Party B the economic equivalent of any payment or delivery (whether the underlying obligation was absolute or contingent and assuming the satisfaction of each applicable condition precedent) by the parties under Section 2(a)(i) in respect of such Terminated Transaction or group of Terminated Transactions that would, but for the occurrence of the relevant Early Termination Date, have been required after that Date, and (ii) has terms which are substantially the same as this Agreement, including, without limitation, rating triggers, Regulation AB compliance, and credit support documentation, save for the exclusion of provisions relating to Transactions that are not Terminated Transaction, as determined by Party B in its sole discretion, acting in a commercially reasonable manner.

  • Controlled Accumulation Period Length has the meaning specified in subsection 4.03(c).

  • Export Transactions Net Activity means the aggregate net total, resulting from Export Transactions, of (i) Spot Market Energy charges, (ii) Transmission Congestion Charges, and (iii) Transmission Loss Charges, calculated as set forth in Operating Agreement, Schedule 1 and the parallel provisions of Tariff, Attachment K-Appendix. Export Transactions Net Activity may be positive or negative. Extended Primary Reserve Requirement:

  • Controlled unaffiliated business means a company:

  • Arms length Transaction”, means a transaction between two related parties that is conducted as if they were unrelated, so that there is no conflict of interest.

  • Subsidiary Redesignation shall have the meaning provided in the definition of “Unrestricted Subsidiary” contained in this Section 1.01.

  • Reference Interconnection Offer or “RIO” means a document published by a service provider specifying terms and conditions on which the other service provider may seek interconnection with such service provider;

  • Restricted Payment Transaction means any Restricted Payment permitted pursuant to Section 409, any Permitted Payment, any Permitted Investment, or any transaction specifically excluded from the definition of the term “Restricted Payment” (including pursuant to the exception contained in clause (i) and the parenthetical exclusions contained in clauses (ii) and (iii) of such definition).

  • Exempt Transaction means an increase in the percentage of the outstanding shares of Common Stock or the percentage of the combined voting power of the outstanding Voting Stock of the Company beneficially owned by any Person solely as a result of a reduction in the number of shares of Common Stock then outstanding due to the repurchase of Common Stock or Voting Stock by the Company, unless and until such time as (a) such Person or any Affiliate or Associate of such Person shall purchase or otherwise become the Beneficial Owner of additional shares of Common Stock constituting 1% or more of the then outstanding shares of Common Stock or additional Voting Stock representing 1% or more of the combined voting power of the then outstanding Voting Stock, or (b) any other Person (or Persons) who is (or collectively are) the Beneficial Owner of shares of Common Stock constituting 1% or more of the then outstanding shares of Common Stock or Voting Stock representing 1% or more of the combined voting power of the then outstanding Voting Stock shall become an Affiliate or Associate of such Person.

  • Roll-Up Transaction means a transaction involving the acquisition, merger, conversion or consolidation either directly or indirectly of the Company and the issuance of securities of a Roll-Up Entity to the Shareholders. Such term does not include:

  • Co-Investment Transaction means any transaction in which one or more Regulated Funds (or its Wholly-Owned Investment Sub (defined below)) participated together with one or more Affiliated Funds and/or one or more other Regulated Funds in reliance on the Order.

  • Exempt Transactions means the transactions described in the section hereof titled “Exempt Transactions.”

  • Qualified Transaction means (a) any sale or other transfer of, or any release of Liens relating to, any Accounts or any books or records relating thereto, so long as (i) the Borrower delivers to the Agent (A) at least five Business Days prior to the proposed closing date of such transaction, a draft Borrowing Base Certificate prepared on a pro forma basis after giving effect to such transaction and (B) on the closing date of such transaction, a final Borrowing Base Certificate prepared on a pro forma basis after giving effect to such transaction and (ii) if the aggregate Credit Exposures of all Lenders exceeds the Borrowing Base in effect on the closing date of such transaction after giving effect thereto, the Borrower prepays Loans and pays cash to the Agent as required by Section 2.10(c) or (b) any other sale or other transfer of, or any other release of Liens relating to, any Accounts or any books or records relating thereto, so long as (i) the aggregate consideration received with respect to the transaction pursuant to which such Accounts are sold or otherwise transferred does not exceed $10,000,000 and (ii) the aggregate book value of Eligible Accounts sold or otherwise transferred pursuant to such transaction does not exceed $1,000,000; provided that no Accounts sold or transferred pursuant to the foregoing clause (a) or (b) shall be used in any securitization, factoring or similar financing program of the Borrower or any of its Subsidiaries.

  • person with a 0.25 per cent. interest means a person who holds, or is shown in any register or record kept by the company under the Companies Acts as having an interest in, shares in the company which comprise in total at least 0.25 per cent. in number or nominal value of the shares of the company (calculated exclusive of any shares held as treasury shares), or of any class of such shares (calculated exclusive of any shares of that class held as treasury shares), in issue at the date of service of the restriction notice;