Cloud storage DSHS Confidential Information requires protections equal to or greater than those specified elsewhere within this exhibit. Cloud storage of Data is problematic as neither DSHS nor the Contractor has control of the environment in which the Data is stored. For this reason:
TOOL STORAGE 1. A company shall provide on all construction jobs in towns and cities, and elsewhere where reasonably necessary and practicable (or if requested buy the employee), a suitable and secure waterproof lock-up solely for the purpose of storing employees’ tools, and on multi-storey and major projects the company shall provide, where possible, a suitable lock-up for employees’ tools within a reasonable distance of the work area of large groups of employees.
Storage The ordering agency is responsible for storage if the contractor delivers within the time required and the agency cannot accept delivery.
Off-Site Storage With prior approval by the Owner and in the event Contractor elects to store materials at an off-site location, abide by the following conditions, unless otherwise agreed to in writing by the Owner.
ON-SITE STORAGE With the written approval of the Authorized User, materials, equipment or supplies may be stored at the Authorized User’s site at the Contractor’s sole risk.
Data Storage Where required by applicable law, Student Data shall be stored within the United States. Upon request of the LEA, Provider will provide a list of the locations where Student Data is stored.
TRANSPORTATION, TRAVEL TIME AND ROOM AND BOARD 14.01 The Employer shall remunerate employees for travel time and mileage as follows:
Petroleum Storage Systems A. At Company’s expense, Company will at all times comply with all federal, state, and local requirements, including but not limited to, the regulations of the FDEP as stated in Chapters 62-761 and 62-762, FAC, the requirements of the Federal Oil Pollution Prevention regulation found in Title 40 of the Code of Federal Regulations Part 112 (40 CFR part 112), as well as the requirements of the Environmental Protection Commission of Hillsborough County (EPC), as may be amended or replaced, pertaining to petroleum storage tank and piping system construction, operation, inspection, and compliance monitoring programs; release detection methods and procedures; maintenance; and preventative maintenance programs. Company will be responsible for all spillage, overflow, or escape of gases, petroleum or petroleum products, and for all fines and penalties in connection therewith. All petroleum storage systems will be registered by Company, and Company will display the registration placard as required by law.
Transport 6.1.1 BellSouth shall provide nondiscriminatory access, in accordance with FCC Rules 51.311, 51.319, and Section 251(c)(3) of the Act to interoffice transmission facilities described in this Section 6 on an unbundled basis to EZ Phone for the provision of a qualifying service, as set forth herein.
Millwright Xxxxx be to assist and work under the direction and instructions I or A. He will work alone at times performing assignments in keeping with his training. During the course of his year, training must become proficient in good practices in the areas of fitting, aligning, lubricating and the operation of all shop tools and machines. In addition to the foregoing, he will be exposed to and the process of learning techniques required in trouble shooting key production machinery, pipe fitting, basic welding and machining but not be expected to display a high degree of proficiency in these areas at this point. Millwright Must be capable of performing the tasks of fittings, aligning, lubricating an able to operate all shop tools and machines. Must under direction become proficient in basic welding and pipe fitting as well as dismantling and reassembly of plant equipment. Under direction,will continueto develop skills in trouble shooting all plant equipment and improve his skills at machining part and be exposed to basic principles of hydraulics and pneumatic. He may work alone frequently, but occasionally will require direction and instructions form Millwright I or A. Millwright 11: be capable, without direction of fitting, aligning and lubrication and taking apart and reassembling plant equipment. In addition, is expected to be able to weld, operate shop tools and do pipe fitting as required. Must under direction, become proficient at effective methods of trouble shooting and repairing hydraulic, pneumatic and mechanical faults in plant machinery. I: Must be capable without direction of performing all practices under Xxxxxxxxxx Must under directionbecomeproficient at reading and understanding blueprints, all phases of installing new equipment, laying out hydraulic and mechanical drives and meet speed and power requirements correctly. Xxxxxxxxxx "A": Must he capable without direction, of performing all under Xxxxxxxxxx X, and Must take full responsibility for work done by himself or his assistant. Must he in possession of a Millwright Certificate or a Machinist Certificate or Welder Certificate. Millwrightspresently employed in this classification will not be required to have a Certificate.