Schematic Drawings Clause Examples

Schematic Drawings. Electrical or electronic schematic drawings in accordance with ASME Y14.15- 2017 shall be prepared for each unit, module and assembly. Schematics shall show electrical connections to each part and assembly, without regard to their physical location.

Schematic Drawings. These documents shall be schematic drawings responding to the educational specifications and program requirements illustrating the general scope, scale, and relationship of project components. In addition to SREF requirements and information required by the Owner’s document submittal checklist for phase I, the documents shall include the following: .1 A site plan showing acreage, points of the compass, scale, contours and general topographical conditions, flood plain elevation and velocity zone, over-all dimensions, adjacent highways, roads, off-site improvements, emergency access, fire hydrants, power transmission lines, ownership and use of adjacent land, walks and paths, vehicle and bike parking areas, accessibility for the disabled, service areas, play areas, athletic fields, bus loop(s), parent drop off, existing buildings and use, location of proposed building(s) and future additions, portable classrooms and other relocatable or temporary structures, community use buildings, phased construction, preliminary soil borings. A statement shall be included on the site plan identifying the FEMA flood plain and velocity zone in which the project is located. The statement shall be signed and dated by the Project Consultant.

Schematic Drawings. Subdivider shall require its consultant to prepare schematic drawings for Project for City approval.

Schematic Drawings. If the Schematic Drawings depicting the layout of the Premises and the location of the Lessee Improvements therein (the "Schematic Drawings") have already been prepared and approved by Lessor and Lessee prior to the full execution of this Lease (which includes this Agreement), then same shall be attached hereto as Exhibit C-3") and made a part hereof. If the Schematic Drawings are not attached as Exhibit "C-3" hereto at the time this Lease is fully executed, then the following procedure shall be used to prepare and approve of the Schematic Drawings. No later than three business (3) days following the full execution of this Lease, Lessee shall meet with the Architect and Continental Development Corporation and determine such information as is necessary or appropriate for the Architect to prepare the Schematic Drawings and other information necessary for each party to insure satisfactory compliance with all aspects of this Agreement. Such information shall include, but not be limited to, building standard unit costs, basic core and shell systems performance criteria and above standard components. This information is to be provided within eight (8) business days of the date of execution. Such Schematic Drawings, upon completion thereof (which in no event shall be more than thirteen (13) business days after the execution of this Lease), shall be submitted to Lessor and Lessee for approval. Within five (5) days after Lessee's receipt of such Schematic Drawings, Lessee shall notify Lessor and Architect of the changes, if any, which Lessee desires to make to such Schematic Drawings, which notice shall be in writing and shall identify with specificity the changes which Lessee desires to make and shall attach a copy of the Schematic Drawings initialed by Lessee and showing the desired changes (the "Lessee's Schematic Notice"). Within five (5) business days following Lessor's receipt of the Schematic Drawings and Lessee's Schematic Notice, Lessor shall either approve or disapprove thereof. If Lessor disapproves, Lessor shall specify in writing the changes which Lessor requires and the Schematic Drawings shall be revised by the Architect to reflect those changes described in Lessee's Schematic Notice which are not disapproved by Lessor and such other items needed to satisfy EXHIBIT "C"

Schematic Drawings. The Redeveloper has prepared Schematic Drawings showing the preliminary size, shape, and location of the Redeveloper Public Improvements. Such Schematic Drawings will serve as the basis for development of final plans and specifications for the Redeveloper Public Improvements to be constructed by the Redeveloper.

Schematic Drawings. Landlord shall cause the Architect, in line with time periods provided for on the Schedule to deliver to Tenant schematic drawings for the Tenant Improvements that are a logical extension of the Space Plans and the TI Specifications (the “Schematic Drawings”). Not more than 5 days thereafter, Tenant shall deliver to Landlord and the Architect the written objections, questions or comments of Tenant with regard to the applicable Schematic Drawings; provided, however, that Tenant may not disapprove any matter that is consistent with the applicable Space Plans without submitting a Change Request. Landlord shall cause the applicable Schematic Drawings to be revised to address such written comments and shall resubmit said drawings to Tenant for approval within 5 days thereafter. Such process shall continue until Landlord and Tenant have approved the applicable Schematic Drawings. The failure (other than as a result of Landlord’s failure to (i) deliver the Schematic Drawings within the time period provided above or (ii) timely respond to Tenant) to complete the Schematic Drawings for the Tenant Improvements in compliance with the Schedule shall constitute a Tenant Delay. Any disputes regarding the applicable Schematic Drawings shall be resolved in accordance with Section 2(f) hereof. Provided that the design reflected in the Schematic Drawings is consistent with the applicable Space Plans, Tenant shall approve such Schematic Drawings submitted by Architect, unless Tenant submits a Change Request.

Schematic Drawings. On or before the date set forth in Schedule B, Tenant and METa Architecture shall prepare and deliver to Landlord for Landlord's approval of the proposed schematic drawings, which shall be a formalization of the Space Program and the Final Space Plan, including outlined specifications. Landlord shall notify Tenant of its approval or disapproval (with reasons for such disapproval specified) of the proposed schematic drawings within five (5) business days after receipt thereof. Landlord shall work diligently with Tenant to prepare a price check of estimated costs for the Tenant Improvements contemplated by such proposed schematic drawings with the expectation that the same will be completed within the week of such approval. Any failure by Landlord to notify Tenant of its approval or disapproval within such five (5) business day period shall be deemed to be Landlord's approval thereof. If Landlord disapproves the proposed schematic drawings, this process shall be repeated until Landlord's approval is obtained; provided, however, that Tenant shall only make such changes to the proposed schematic drawings which address the reasons Landlord specified for its disapproval of the proposed schematic drawings. The approved schematic drawings are hereinafter referred to as the "Final Schematic Drawings."

Schematic Drawings. The preliminary size, shape and location of the Private Improvements are schematically outlined on Exhibit “D” (“Private Improvement Schematic Drawings”). The Private Improvement Schematic Drawings also include a delineation of construction materials to be used for the exterior walls of the Private Improvements. The Private Improvement Schematic Drawings have been approved by the City and will serve as the basis for development of final plans and specifications for the Private Improvements to be constructed by the Redeveloper. Prior to being approved by the City, the Private Improvement Schematic Drawings were presented to the City’s Urban Design Committee for its review and recommendation as to approval.

Schematic Drawings. The Schematic Drawings shall include: 1.3.3.1. Site plan at appropriate scale showing relationships of buildings with their respective uses designating open spaces, terraces, landscaped areas, walkways, loading areas, streets, water elements, and adjacent uses. Adjacent existing and proposed street, structures, parks, and mid- block breaks should also be shown. Scale: minimum 1/16” = l’. Site Plans for the Neighborhood Towers shall show the relationship of the Neighborhood Tower to the Neighborhood Park. 1.3.3.2. A description of any stormwater treatment measures proposed for the parcel, including the location and size of facilities. 1.3.3.3. Site sections showing height relationships of those areas noted above. Scale: minimum 1/16” = l’. 1.3.3.4. Building plans (typical floor plans, ground plane plans, roof plans), elevations and sections sufficient to describe the development proposal, the general architectural character, and materials proposed at appropriate scale to fully explain the concept. Scale: minimum 1/8” = 1’. 1.3.3.5. Isometric or axonometric drawings to illustrate overall project and the building dimensions, bulk, setbacks, stepbacks, and streetwall. If the building is on YBI, drawings must demonstrate that the building conforms to the height limits set forth in the Public Trust Exchange Agreement. 1.3.3.6. Detailed study materials as needed to examine critical urban design elements including building modulation and surface treatment, window systems, setback areas, building entries, parking and loading entries, retail storefronts, and rooftop elements. 1.3.3.7. Conceptual design of mid-block breaks if applicable, including landscaping plans, travel way dimensions, sections, planting materials, furnishing, lighting and paving materials selection. Additional materials to illustrate unique building design elements or demonstrate conformance with design guidelines.