Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ASME B16.1
Referenced Standards. Policies and Specifications 5
Referenced Standards. For erosion control best management practices (BMPs), this standard reference the City of Madras Stormwater Master Plan, ODOT Hydraulics Manual, and Central Oregon Storm water Manual.
Referenced Standards. The IBC, IMC, IECC, IPC and IFGC standards shall be utilized to provide specific, or prescriptive, requirements on how to achieve the requirements established in the code. These standards may be unique to the code or may be derived from other established industry standards. Recognized standards may also be used to show compliance with the standard of duty established by the code. EXHIBIT B CODE COMPLIANCE PLAN REVIEW PROCEDURES
Referenced Standards. Materials and test procedures shall conform with the published requirements of the various societies or institutes as stated in this specification. The current edition of each standard shall be used. ASTM C33 Concrete Aggregates ASTM C39 Method of Test for Compressive Strength of Cylindrical Concrete Specimens ASTM C70 Test Method for Surface Moisture in Fine Aggregates ASTM C109 Test Method for Compressive Strength of Hydraulic Cement ASTM C114 Methods for Chemical Analysis of Hydraulic Cement ASTM C131 Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine ASTM C136 Test Method for Sieve or Screen Analysis of Fine and Coarse Aggregates ASTM C143 Method of Test for Slump of Portland Cement Concrete ASTM C150 Standard Specification of Portland Cement ASTM C172 Sampling Fresh Concrete ASTM C191 Test Method for Time of Setting of Hydraulic Cement by Vicat Needle ASTM C192 Method of Making and Curing Concrete Test Specimens in the Laboratory ASTM C204 Test Method for Fineness of Portland Cement by Air Permeability Apparatus UPRR Concrete Tie Specification Page 3/18 September 2003 ASTM C227 Potential Alkali Reactivity of Cement Aggregate Combinations (Mortar - Bar Test) ASTM C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method ASTM C260 Air Entraining Admixtures for Concrete ASTM C295 Recommended Practice for Petrographic Examination of Aggregates for Concrete ASTM C359 Test Method for Early Stiffening of Portland Cement (Mortar Method) ASTM C403 Time of Setting of Concrete Mixtures by Penetration Resistance ASTM C430 Test Method for Fineness of Hydraulic Cement by the No. 325 Sieve ASTM C457 Practice for Microscopical Determination of Air Void Content and Parameters of the Air Void System in Hardened Concrete ASTM C494 Chemical Admixtures for Concrete ASTM C586 Potential Alkali Reactivity of Carbonate Rocks for Concrete Aggregate (Rock Cylinder Method) ASTM C617 Capping Cylinder Concrete Specimens ASTM C666 Test Method for Resistance of Concrete to Rapid Freezing and Thawing ASTM C779 Test Method for Abrasion Resistance of Horizontal Concrete Surfaces ASTM C1231 Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders ASTM C5329 Recommended Practice for Inspection and Testing Agencies far Concrete, Steel and Bituminous Materials used in Construction ASTM A536 Ductile Iron Castings ASTM A 881 Steel Wire, Deformed, Stress...
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ASTM A36 Standard for Carbon Structural Steel ASTM A153 Standard for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM A193 Standard for Alloy-Steel and Stainless Steel Bolting Materials for High- Temperature Service ASTM A194 Standard for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High- Temperature Service, or Both ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A320 Standard for Alloy Steel Bolting Materials for Low Temperature Service ASTM A563 Standard for Carbon and Alloy Steel Nuts ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings ASTM B695 Standard for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain (Flat), Unhardened for General Use ASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete Elements May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 - 2 ANCHORAGE TO CONCRETE
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of a listed document, the requirements of this Section shall prevail. Reference Title ASME SEC VIII Boiler and Pressure Vessel Code, Pressure Relief Devices
Referenced Standards. The grading requirements of this section are focused on protection of water quality and drainage courses and to also protect newly formed lots and adjacent properties. In cases where additional clarification is needed for acceptable grading practices, the City and applicant will reference Part 200 and Part 300 of the latest edition of the Oregon Standard Specifications for Construction. In cases of conflict, the provisions of this section will govern. Grading plans must conform to the following design criteria unless approved otherwise by the City. To justify a variance from these requirements, the applicant will be required to furnish a geotechnical engineering or engineering geology report (or both) which states that the site has been investigated and that a less-restrictive criteria will not create an unstable condition posing a hazard to public or private property. These reports must be submitted to the City for its review and final approval.
Referenced Standards. Comply with all codes and standards (latest versions) applicable to this type of work, including:
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title Chapter 296-155 WAC, Part N Excavation, Trenching, and Shoring AWS D1.1 Structural Welding Code IBC International Building Code
