Policies and Standards. The NCGRL will provide and manage library services that conform to relevant national, state and local government policies and standards, as well as those policies and standards set by the NCGRL Board. If, for any reason, this is not achievable, the NCGRL will report those areas of non-conformance to the Library Board and recommend appropriate strategies to achieve conformance. Where the non- conformance creates or may create a public or occupational health and safety risk, the NCGRL will take immediate action to eliminate the risk, including the temporary or permanent closure of library services if appropriate.
Policies and Standards. Practitioner’s failure or refusal to comply with the policies, standards, and regulations of the Employer, which includes, but is not limited to, utilization management, quality improvement, or credentialing policies, which from time to time may be established by the Employer and of which the Practitioner has received prior written notice;
Policies and Standards. The Health Care Provider will advise the Educator of all applicable health standards for persons placed with it and will make available copies of any by-laws, policies, rules, procedures and requirements applicable to the Educator, its students and instructors of the Educator relative to the placements contemplated by this Agreement.
Policies and Standards. RingCentral has established, and will maintain, documented policies or standards appropriate to govern the handling of Confidential Customer Data in compliance with the Agreement and applicable law.
Policies and Standards. DPH will establish policies and standards (respectively, "Policies and Standards") that will govern DPH's and Participant's activity on the Exchange, and these Policies and Standards will be made available. These Policies and Standards will govern DPH and Participant use of the Exchange and the use, submission, transfer, access, privacy and security of Data.
Policies and Standards. Changes to these Policies and Standards shall be classified as Corrections or Revisions. Corrections represent minor technical fixes or clarifications that do not represent a substantive change in policy, standards or procedures. Revisions represent substantive changes in policy (or new policies), standards or procedures. The last page of this document shall contain a running list showing the date that any Corrections or Revisions were made, and referring to any documentation of such changes, in order to maintain a record of such changes. That record follows this section.
Policies and Standards. 10.1 The Supplier shall comply with all the Customer policies and procedures notified by the Customer to the Supplier from time to time insofar as they are relevant to the supply of the Goods and/or Services including, without limitation:
Policies and Standards. The necessary data policies have been outlined at the former deliverables of the work package, however it is necessary to highlight that the success on the application of the Data Management plan is highly dependent on the “tempos” of data and metadata creation. In several previous EU projects, such as Eurofleets(1) and Eurofleets2, SeaDataNet 1 and 2 and ODIP 1 and 2, where data management of research vessels has been a key issue, it has been shown that data and metadata should be created as close as possible to the moment of data acquisition. This means that the main production of data and metadata products must be on board and, therefore, a great effort in the implementation of the data management plan should be focused on the ship's facilities. For Metadata is recommended the use of ISO 19115 content model as it is the common accepted metadata model to follow the European INSPIRE directives. According to Article 5(1) of Directive 2007/2/EC, Member States shall ensure that metadata are created for the spatial data sets and services corresponding to the themes listed in Annexes I, II and III, and that those metadata are kept up to date. According to Article 5(4) of Directive 2007/2/EC, Implementing Rules shall be adopted taking account of relevant, existing international standards and user requirements. In the context of metadata for spatial data and spatial data services, the standards EN ISO 19115, EN ISO 19119, and ISO 15836 (Dublin Core) have been identified as important standards. Following the SeaDataNet approach, as it is an EU reference project in marine data management, the ARICE XML Schema's should be based upon the ISO 19115 DTD. As in SeaDataNet, two main Metadata schemas should be considered. For the cruise description the Cruise Summary Report (CSR) should be considered, and for Data sets description, the Common Data Index (CDI). Both CSR and CDI are an upgrade to ISO 19139 format has been applied, especially for making these INSPIRE compliant and for making the exchange between the national providers and the central portal operators more efficient by automatic harvesting. Moreover, following the SeaDataNet approach, ARICE metadata formats should use of the SeaDataNet Common Vocabularies and the EDMO directory (European Directory of Marine Organizations) which underpins the relations and semantic coherency between the different metadata services. The SeaDataNet vocabulary services are technically managed and hosted by the British Oceanograp...
Policies and Standards. American Urological Association agrees to: 1) abide by the ACCME Standards for Commercial Support of Continuing Medical Education; 2) acknowledge educational support from the commercial company in program brochures, syllabi, or other program materials; and 3) upon request, furnish the commercial supporter a report concerning the expenditure of the funds provided. The Commercial Supporter agrees to abide by all requirements of the Accreditation Council for Continuing Medical Education (ACCME) Standards for Commercial Support of Continuing Medical Education (appended). American Urological Association Tax ID Number: 00-0000000 Contact Person: Email Address: Phone Number: Fax Number: (Company’s name) Address: Contact Person: Email Address: Phone Number: Fax number: AGREED BY AUTHORIZED REPRESENTATIVES Signature: Date: Commercial Company Representative: Signature: Date: AUA Office of Education Director, Xxxxxx Xxxx, M.A.
Policies and Standards. 2.3.3. The Contractor must comply with all relevant policies and standards. These may include but are not limited to: BS EN ISO 15011-4:2006+A1:2008 Health and safety in welding and allied processes. Laboratory method for sampling fume and gases. BS 499-1:2009 Welding terms and symbols. Glossary for welding, brazing and thermal cutting BS EN ISO 9001:2008 Quality management systems or equivalent BS ISO 8015:1985 Technical drawings. Fundamental tolerancing principle BS ISO 2692:1988 Technical drawings. Geometrical tolerancing. Maximum material principle BS 308-2:1985 Engineering drawing practice. Recommendations for dimensioning and tolerancing of size ISO/TR16570 : 2004 Geometric product specifications - linear and angular dimensioning and tolerancing, +/- limit specifications - Step dimensions, distances, angular sizes and radii
