Plans and Drawings Clause Examples

Plans and Drawings. As soon as available, plans and specifications and as-built drawings for the Facility including the civil and architectural works.

Plans and Drawings. As soon as available, plans and specifications and as-built drawings for the Facility including the civil and architectural works. (i) Quality Control Programs

Plans and Drawings. As soon as possible following the execution and delivery of this Lease, Landlord and Tenant shall complete a Space Plan for the Premises (the "Space Plan"). Following approval of the Space Plan by Landlord and Tenant, Landlord shall deliver to Tenant for Tenant's approval working drawings consisting of a floor plan, reflected ceiling plan, interior elevations, electrical plan, door schedule and finish schedule for the Premises (the "Working Drawings"), which Working Drawings shall be consistent with the Space Plan. The Working Drawings as finally approved by Tenant are referred to as the "Final Plans", and the improvements to the Premises shown in the Final Plans are sometimes referred to herein as the "Landlord's Work". Following approval of the Final Plans, Landlord shall obtain all permits and approvals and construct or modify the improvements to the Premises in accordance with the Final Plans, in a first-class workmanlike manner, and charge the Tenant Improvement Allowance for an amount equal to the costs incurred by Landlord in constructing the improvements, including, without limitation, Landlord's actual cost of the work performed and materials provided, architectural fees, engineering fees, mechanical costs, structural costs, electrical costs, construction management fees (not to exceed five percent (5%) of the total cost), permit fees, out-of-pocket expenses, and any increased costs incurred by Landlord as a result of any changes to the Final Plans requested by Tenant or any delay caused by Tenant (collectively, "Construction Costs"). Tenant shall pay or reimburse Landlord within five (5) days after Landlord's request for any Construction Costs in excess of the Tenant Improvement Allowance incurred by Landlord in constructing the improvements in accordance with the Final Plans, and Landlord shall have no obligation to proceed with construction until such excess Construction Costs are received.

Plans and Drawings. Tenant shall submit to Landlord Tenant’s proposed space plan for the Premises (the “Space Plan”). Landlord shall approve or disapprove the Space Plan within five (5) business days after delivery of the Space Plan to Landlord, which approval shall not be withheld unless a Design Problem (as defined in Section 8(a) ) exists or conditioned. If Landlord reasonably disapproves the Space Plan because of a Design Problem, Landlord shall return the Space Plan to Tenant with Landlord’s specific requested changes noted thereon. Tenant shall revise and resubmit the Space Plan to Landlord and Landlord shall approve or disapprove such revised Space Plan if a Design Problem exists within five (5) business days of receipt. After Landlord’s approval of the Space Plan, Tenant shall deliver to Landlord for Landlord’s approval working drawings consisting of a floor plan, reflected ceiling plan, interior elevations and electrical plan (the “Working Drawings”), which Working Drawings shall be consistent with the Space Plan. Landlord shall approve or disapprove the Working Drawings within five (5) business days after delivery of the Working Drawings to Landlord, which approval shall not be withheld unless a Design Problem exists or conditioned. If Landlord disapproves the Working Drawings, Landlord shall return the Working Drawings to Tenant with Landlord’s specific requested changes noted thereon. Tenant shall revise and resubmit the Working Drawings to Landlord and Landlord shall approve or disapprove such revised Working Drawings if a Design Problem exists within five (5) business days after receipt. The Working Drawings as finally approved by Landlord are referred to as the “Final Plans.” The Space Plan and Working Drawings may be submitted by Tenant in one or more stages and at one or more times, and the time periods for Landlord’s approval shall apply with respect to each such portion submitted. Tenant shall obtain all permits and approvals necessary for all of the Tenant Improvements and construct and install all Tenant Improvements within the Premises using Tenant’s Contractor in accordance with all applicable Laws and the Final Plans, in a first-class and workmanlike manner. In the event Tenant needs to make changes to the Final Plans, Tenant shall submit all Material Change Orders to Landlord for Landlord’s approval, which approval shall be given or denied (and if denied, only if a Design Problem exists and specifying the reasons for denial) within three (3) to five (...

Plans and Drawings. 25.1 In the event the bid is accepted the contractor shall have to supply 5 copies of detailed design of units and structural design calculations with drawings showing plan, cross-section, elevations, mechanical equipments clearly to the complete satisfaction of the Employer and within a reasonable time fixed by the Employer. 25.2 The Contractor shall submit the following information, in 5 copies to the Engineer-in-charge for approval within the time stipulated against each item below: (a) a general layout plan of construction plant and equipment for the execution of the work, within 30 days from the date of notice to proceed with the work; (b) drawings or plan showing the location of major plants and other facilities which he proposes to put up at the site, including any changes in the general layout, at least 14 days prior to the commencement of the respective work; and (c) any other details and drawings as required under contract at the times specified in the contract. (d) detail design of units and structural design calculations with drawings showing plan, cross section, elevation.

Plans and Drawings. Notated Drawings comprising sheets numbered to The Specification The Builder’s scope of work for the Building Work or other document describing and/or providing a breakdown of the Building Work and materials that will be required to construct the Building and listing any Building Work or materials that are the Owner’s responsibility Any Addition or Modification to the Specification SIGNED FOR & ON BEHALF OF THE BUILDER SIGNED FOR & ON BEHALF OF THE OWNER(S) Name(s) of Owner(s) THE PARTIES AGREE as follows:

Plans and Drawings. See Exhibit A-2.

Plans and Drawings i) The SELLER shall submit to the Buyer three (3) copies of each of the class approved plans and drawings for reference purpose only. ii) The SELLER undertakes to deliver to the Buyer the following drawings: SHIP STRUCTURE: General Arrangement Midship Section (Showing longitudinal and transverse material) Capacity Plan Lines Plan Longitudinal Plan Drawings of Shell Expansion Drawings of Oil tight and Watertight bulkheads Drawings of all Double Bottom Construction Drawings of Fire Division Zone Drawings of Cargo holds and Container stowage on deck Drawing of Cargo holds Ventilation Drawings of Aft end construction Drawings of Engine Room construction Drawings of Engine Thrust Seating Drawings of Fore End Construction Drawings of Xxxxx frame Drawings of Rudder, Stock and Tiller Preliminary Loading Manuals Welding Details Date: 13th November, 2013 Detailed Drawings of the Engine Room Arrangement All Shafting, Thrust, Intermediate and Tail Xxxxx Xxxx Arrangement Calculations for Shaft Vibration (torsional, Axial and lateral) Calculations for Heat Balance Piping Schemes of Ballast, Bilge, Fuel oil, Lub. Oil, Air and Sounding, Engine Room Ventilation, Compressed Air, Sanitary Water, Fire Fighting Water Main and Emergency Switchboard, Main Cable Route One Line Diagram Calculations for Electric Balance iii) The plans and drawings approved by the Class shall be final, and any alteration thereof shall be regarded as modification specified in ARTICLE V.

Plans and Drawings. All plans, drawings, specifications, technical data, designs, computer programs, reports or other information (hereinafter referred to as “data”) produced by Supplier in tangible form in the performance of the Work to be provided under the Contract, will be the property of Xxxxxx and Supplier will be provided with copies of the data for its own use as may be required in the ordinary course of its business. Should any drawing or specification prepared by Supplier be incorrect or require amendment, in addition to any other rights or remedies Xxxxxx may have under the Contract or in law or equity, Irving may require Supplier to rectify the drawing or specification, all at the expense of Supplier.