Product Warranty; Product Liability (a) Except as set forth on Company Disclosure Schedule 4.23, the products produced, sold or delivered by the Company in conducting the Business have been in all material respects in conformity with all product specifications and all applicable Laws. To the Company’s Knowledge, the Company has no material Liability for damages in connection therewith or any other customer or product obligations not reserved against on the Balance Sheet.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
Product Warranty Seller provides general warranties of fitness and general warranties that the goods are free from defects, for 1 year from acceptance of the goods, except as may otherwise be set forth in the Description/Proposal, or other attached warranty.
Product Warranty and Product Liability Schedule 5.17 of the Disclosure Schedule contains a true, correct and complete copy of Company's standard warranty or warranties for sales of Products (as defined below) and, except as stated therein, there are no warranties, commitments or obligations with respect to the return, repair or replacement of Products. Schedule 5.17 of the Disclosure Schedule contains a description of all product liability claims and similar claims, actions, litigation and other proceedings relating to Products which are presently pending or which to Company's knowledge are threatened, or which have been asserted or commenced against Company within the last two (2) years, in which a party thereto either requests injunctive relief (whether temporary or permanent) or alleges damages in excess of $100,000.00 (whether or not covered by insurance). To the best of the Company's knowledge, there are no defects in design, construction or manufacture of Products which would adversely affect performance or create an unusual risk of injury to persons or property. Except as set forth on Schedule 5.17, none of the Products has been the subject of any replacement, field fix, retrofit, modification or recall campaign other than in the ordinary course of business. The Products have been designed and manufactured so as to meet and comply with all governmental standards and specifications currently in effect, and have received all governmental approvals necessary to allow their sale and use. As used herein, the term "Products" means any and all products currently or at any time previously manufactured, distributed or sold by Company, or by any predecessor of Company under any brand name or xxxx under which products are or have been manufactured over the last three (3) years, distributed or sold by Company, in or through the Business.
Defective Products None of the Group Companies has manufactured, sold or supplied products which are, or were, in any material respect, faulty or defective, or which do not comply in any material respect with any representations or warranties expressly made by such Group Company, or with all applicable regulations, standards and requirements.
API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.
Manufacture of Products All Products marketed through Grantor's Web ------------------------- Site shall be manufactured, packaged, prepared, and shipped in accordance with the specifications and requirements described on Exhibit A hereto as it may be modified from time to time. Quality control standards relating to the Product's weight, color, consistency, micro-biological content, labeling and packaging are also set forth on Exhibit A. In the event that Exhibit A is incomplete, Products shall be manufactured and shipped in accordance with industry standards.
Licensed Software Computer program(s) provided by Contractor in connection with the Deliverables, subject to Section 14 of this Contract.
Supply of Products During the term of this Agreement and any extension hereof, the Seller shall sell and supply the products as set out in Schedule 1 hereto (“Products”) to SiPM and SiPM shall buy from the Seller such Products on a non-exclusive basis. The specifications of the Products are set out in Schedule 2 hereto. SUPPLY AGREEMENT - SiPM A Supply Agreement is a document between two parties, a Supplier and a Purchaser. The Supplier can be an individual or business and is the party that " supplies," or sells, the goods to the Purchaser. The Purchaser can also be an individual or a business and is the party that purchases for its use the goods that the Supplier provides.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
