Milk Temperature Sample Clauses

Milk Temperature. Milk received at the factory with a temperature higher than 5.0°C is non-conformant, an investigation by Norco Foods and Milk Supply to determine the cause of the high temperature will be conducted. An assessment as to whether the milk is within specification will be made. In extenuating circumstances, milk above 4.0°C can be collected on-farm subject to review of the situation by Norco Milk Supply.
AutoNDA by SimpleDocs
Milk Temperature. Milk cooling is a critical component in maintaining milk quality standards. To comply with food safety regulation, dairy farm licence and export market requirements, milk must be cooled to 5°C or less within 3.5 hours of the commencement of milking. Milk collection temperature To maximise transport efficiencies, milk may be collected soon after milking even though milk may not be cooled to the expected temperature. Should the supplier’s milk collection occur within 2 hours from the completion of milking, milk may be pumped into the milk tanker at temperatures above 5°C (subject to conducting sensory grading and applying the temperature assessment in Graph 1). In applying the temperature assessment in Graph 1, tanker drivers will use the milking completion time displayed in the supplier’s milk room as the basis for the calculation. Failure to clearly display accurate milking times may result in a supplier’s milk being rejected due to temperature non-conformance. For milk out of the above temperature and time specifications, in the first instance, the Supplier’s Field Services Officer will contact the supplier to ascertain the cause of the issue, which is then to be rectified and a Corrective Action Report completed. Subsequent failure to eliminate the problem, may result in the milk being paid as grade milk. Vat breakdown or power failure The supplier must contact their Field Services Officer immediately when milk cooling is interrupted for example, due to vat breakdown or power failure.

Related to Milk Temperature

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Technical Specification As enumerated in Special Conditions of Contract/Scope of Work/attached Drawing/ Details/Schedule of Rates.

  • Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.

  • Outputs 11. The objectives and outcomes of this Agreement will be achieved by:

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

  • Tolerances 1. If a non-originating material used in the production of a product does not satisfy the requirements set out in Annex 3-B, the product shall be considered as originating in a Party, provided that:

  • Signaling Parameters All SS7 signaling parameters will be provided in conjunction with traffic exchange trunk groups, where and as available. These parameters include Automatic Number Identification ("ANI"), Calling Party Number ("CPN"), Privacy Indicator, calling party category information, originating line information, charge number, etc. Also included are all parameters relating to network signaling information, such as Carrier Information Parameter ("CIP"), wherever such information is needed for call routing or billing. GTE will provide SS7 via GR-394-SS7 and/or GR-317-SS7 format(s).

  • Health plan specification The Employer will require health plans participating in the Group Insurance Program to develop and implement health promotion and health education programs for State employees and their dependents.

  • Tolerance Average net mass of cement packed in bags in a sample shall be equal to or more than 50kg. If and as desired by the Engineer-in-Charge, the number of samples to be checked for net mass of cement per bag, in a given number of bags shall be as given below: 100 to 150 bags : 20 sample 150 to 280 bags : 32 sample 281 to 500 bags : 50 sample 501 to 1200 bags : 80 sample 1201 to 3200 bags : 125 sample 3201 and above : 200 sample The bags in a sample shall be selected at random. B- Sand (Fine Aggregate)

  • Smoke Detectors At Owner's expense, smoke detectors will be installed on the Property in working condition in accordance with the law prior to the tenant's occupancy. During the occupancy, it shall be the tenant's responsibility to maintain all smoke detectors. Owner will replace smoke detector equipment as needed.

Time is Money Join Law Insider Premium to draft better contracts faster.