Measuring device Sample Clauses

Measuring device. 4.1. The measuring device shall consist of two parts: one handle and one measuring part which is a load cell (see figure 2).
Sample 1Sample 2Sample 3See All (12)
AutoNDA by SimpleDocs
Measuring device all the measuring and calculation equipment located either at a Delivery Station or at any other point on the Network, and remote transmission equipment and calculation systems or procedures used by GRTgaz to determine the quantities of natural Gas taken off at an Entry Point or delivered at a Delivery Point, along with their characteristics and Energy Content. Month: period starting at six a.m. (06:00) (CET) on the first day of a given calendar month and ending at six
Sample 1Sample 2Sample 3See All (7)
Measuring device. The official measuring devices for this event are Hawg Trough or Ketch Board. All other brands or types of measuring devices must be approved by the tournament director. Each contestant must bring the measuring board they plan to use for the event and have it verified by the Tournament Director. Anyone found to be using a measuring device that is determined to not be legal will be disqualified from this event. Here is a link to buy a Ketch Karbonate 26” measuring device… it is considered the best!: xxxxx://xxx.xxxxxx.xxx/Ketch-Karbonate-Fish-Measuring- Board/dp/B0B2XBHW9X?th=1&psc=1 Photo Criteria: • Anglers must be prepared to manually upload pictures with cables, cords, software, required to download photos via a USB port to the official judge’s computer @ iAngler. • Each fish photo must include all of the following criteria to avoid penalties or disqualification: • The entire Bass, from the tip of the lip to the end of the tail, on an approved measuring device, while in a tournament legal vessel. • Lying with the tip of the lip against the post end of the measuring device. • The mouth of the Bass can be OPEN. Lower jaw of fish must be touching the bump on the board. • The tail of the Bass must be lying flat on the board, and will be measured to the longest point. • Bass must be facing to the left, tail to the right, belly toward the angler. • Measuring device markings must be clearly visible. Including the actual numbers. • Assigned unique identifier must be visible. • One overhead photo shot frame (not shot at an angle). • Fish must be clear of any holding devices. • Lip, eye, and tail cannot be obstructed in the photo, even by your hand or identifier. Xxxx begins just behind the top and bottom fin of a fish, the ends of these fins must be visible. • Hand or fingers must not be under the xxxx plate, touching gills. • Original/Raw Photo only - Screenshots, Crops, Duplicates and edited photos will be disqualified. Example of correct fish orientation below- Permitted Fishing Methods: Participants should make every effort to release their fish alive after catching and photographing. Participants may not fish more than one rod at a time, and a cast must be fully retrieved before the angler may pick up another rod. All fish must be caught via a fishing rod, line and hook using live, dead bait, or an artificial lure on the day of the tournament during tournament hours. All fish must be caught via kayak. Xxxx/shore fishing is allowed provided the kayak was the...
Sample 1
Measuring device. Quantity no.: 1 Make/Type : Totco Deviation range degree: 0 - 8 / 0-12
Sample 1
Measuring device. All Ketch Product measuring boards & Hog Troughs are the official, mandatory, measuring devices for the
Sample 1
Measuring device. (i) All Ketch Products measuring boards are the official mandatory measuring devices for the Bassmaster Kayak Series events and its subsidiaries.
Sample 1
Measuring device. The agree that a carbon monoxide made available when requested by Committee in a plant. EMERGENCY EVACUATION: evacuated.
Sample 1
AutoNDA by SimpleDocs
Measuring device. Quantity: no. N/A Make/type: Deviation range: degree
Sample 1
Measuring device. A. Acceptable measuring boards include Fishing Online measuring board, NE Bassin measuring board and the Ketch Co Measuring Board, and/or other similar plastic and aluminum measuring boards. No rulers, onboard molded rulers, tape measures, etc.
Sample 1

Related to Measuring device

  • Measurement Should the State terminate this contract as herein provided, no fees other than fees due and payable at the time of termination shall thereafter be paid to the Engineer. In determining the value of the work performed by the Engineer prior to termination, the State shall be the sole judge. Compensation for work at termination will be based on a percentage of the work completed at that time. Should the State terminate this contract under paragraph (4) or (5) above, the Engineer shall not incur costs during the thirty-day notice period in excess of the amount incurred during the preceding thirty days.

  • Cost of Metering The Issuer shall not be obligated to pay any costs associated with the routine metering duties set forth in this Section 2, including the costs of installing, replacing and maintaining meters, nor shall the Issuer be entitled to any credit against the Servicing Fee for any cost savings realized by the Servicer as a result of new metering and/or billing technologies.

  • Measurement and Monitoring Tools Contractor shall implement measurement and monitoring tools and procedures reasonably designed to measure its performance of the Services and assess such performance against any applicable service levels. Contractor shall provide LAUSD with a monthly report of service level performance under any applicable Work Order. Upon LAUSD’s request, Contractor shall provide LAUSD with access to the measurement and monitoring tools described herein, and to any information that they generate.

  • Monitoring System In each case in which the Custodian has exercised delegated authority to place Assets with a Foreign Custodian, the Custodian shall establish a system, to re-assess or re-evaluate selected Foreign Custodians, at least annually in accordance with Rule 17f-5(c)(3).

  • Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

Time is Money Join Law Insider Premium to draft better contracts faster.