Limited Power Output Warranty. The output power of the Limited Warranty which is based on the labeled power from BYD shall be in accordance with the followings: For Standard Polycrystalline Module Products: Within a period of one (1) year from the Warranty Start Date, the average output of the modules will be at least 97.5% of the rated power output specified in the original product label. During the next twenty-four (24) years, the average output of the modules will degrade no more than 0.73% per year of the rated power output specified in the original product label. Therefore, at the end of the warranty period, the guaranteed module power output will be at least 80% of the rated power output specified in the original product label. For Standard Monocrystalline Module Products: Within a period of one (1) year from the Warranty Start Date, the average output of the modules will be at least 97% of the rated power output specified in the original product label. During the next twenty-four (24) years, the average output of the modules will degrade no more than 0.7% per year of the rated power output specified in the original product label. Therefore, at the end of the warranty period, the guaranteed module power output will be at least 80.2% of the rated power output specified in the original product label. For Standard Double Glass Polycrystalline Module Products: Within a period of one (1) year from the Warranty Start Date, the average output of the modules will be at least 97.5% of the rated power output specified in the original product label. During the next twenty-Nine (29) years, the average output of the modules will degrade no more than 0.5% per year of the rated power output specified in the original product label. Therefore, at the end of the warranty period, the guaranteed module power output will be at least 83% of the rated power output specified in the original product label. For Standard Double Glass Monocrystalline Module Products: Within a period of one (1) year from the Warranty Start Date, the average output of the modules will be at least 97% of the rated power output specified in the original product label. During the next twenty-Nine (29) years, the average output of the modules will degrade no more than 0.5% per year of the rated power output specified in the original product label. Therefore, at the end of the warranty period, the guaranteed module power output will be at least 82.5% of the rated power output specified in the original product label.
Limited Power Output Warranty. The output power of the Limited Warranty which is based on the report of output power of flash test (Photovoltaic Simulator Test) from BYD shall be in accordance with the followings: （1） Within a period of one (1) year from the Warranty Start Date, the average output of the modules will be at least 97.5% of the rated power output specified in the original product label.
Limited Power Output Warranty. 30 years Subject to the conditions and exclusions contained below, Silfab Solar warranties that within the first year from the Warranty Start Date, every Product will have a power output that is: (a) in the case of mono- crystalline modules, 97.1% of the nameplate maximum power output specified for the Product (“Pmax”); and
Limited Power Output Warranty. PANASONIC warrants the power output will be no less than 97% of the designated Maximum Power (Pmax) stated in the product data sheet for the first year from date of purchase of the Product by the Customer and the power output degradation will be no more than 0.26% per year for the following 24 years, so that, at the end of 25th year, the power output will be at least 90.76% of Pmax. The power output values under this Limited Power Output Warranty shall be those measured under PANASONIC’S Standard Test Conditions (STC) as follows: (a) Irradiance 1000 W/m2, (b) Cell Temperature of 25ºC, and (c) Air Mass of 1.5g. Upon receipt of a Power Output warranty claim, PANASONIC or its designated representative shall conduct measurements under STC to determine the actual power output of the Product. PANASONIC’s measurement shall be the sole determination for purposes of warranty settlement. If PANASONIC measures power output levels under the warranted output levels set out above, taking into account a ±3% measurement tolerance range, and such power loss is the result of a product defect, as determined by PANASONIC in its sole and absolute discretion, PANASONIC will supplement the power output deficiency using one of the following Limited Warranty Remedies as set forth under Section 4 below.
Limited Power Output Warranty. Panasonic USA warrants the power output will be no less than 98% of the designated Maximum Power (Pmax) stated in the Product data sheet for the first year from date of purchase of the Product by the Owner and the power output degradation will be no more than 0.25% per year for the following 24 years, so that, at the end of the 25th year, the power output will be at least 92% of Pmax. The power output values under this Limited Power Output Warranty shall be those measured under Panasonic USA’s Standard Test Conditions (STC) as follows: (a) Irradiance 1000 W/m2, (b) Cell Temperature of 25ºC, and (c) air mass AM1.5g. Upon receipt of a in-warranty Limited Power Output Warranty claim, Panasonic USA or its designated representative may conduct additional measurements, including measurements under STC, to determine the actual power output of the Product. Should Panasonic USA decide to conduct such additional measurements, the results of Panasonic USA’s measurement shall be the sole determination for purposes of warranty settlement. If Panasonic USA’s measurements confirm the claim that power output levels of the Product are below the warranted output levels set out above, taking into account a ±3% measurement tolerance range, and such power loss is the result of a Product manufacturing defect, as determined by Panasonic USA in its sole and absolute discretion, Panasonic USA will provide one of the Limited Warranty Remedies as set forth under Section 4 below at no additional cost to Owner.
Limited Power Output Warranty. In addition, for the Products listed under Sec.1 a),b) Xxxxx Solar warrants that for a period of twenty- five years commencing on the Warranty Start Date; and for the Products listed under Sec. 1 c), d) and the front side (without J-Box) of Products listed under Sec.1 e), f) Xxxxx Solar warrants that for a period of thirty years commencing on the Warranty Start Date, the loss of power output relating to the initial guaranteed power which is defined as Peak Power Xxxxx Pmax(Wp) plus Peak Power Xxxxx Pmax(Wp) multiplied by the lower limit of the Power Output Tolerance Pmax(%)–as specified in the relevant Product Data Sheet and measured at Standard Test Conditions (STC: irradiation 1000w/m²,temperature 25°,AM 1.5) for the Product(s) shall not exceed and measurement shall either be carried out by Xxxxx Solar or by a third-party testing institute recognized by Xxxxx Solar and the customer. (Remark: According to STC, Measurement system uncertainty should be included in all actual power output measurements.)
Limited Power Output Warranty. Boviet guarantees that, for a period of thirty (30) years, the Mono bifacial double-glass PV modules series will maintain the performance as below:
Limited Power Output Warranty. Period Remarks Example At the Time of Purchase The Maximum Power (Pmax) stated in “Specification of Photovoltaic Module” 200 Xxxxx 0-10 years 90% of the Minimum Power (Pmin) 162 Xxxxx 10-20 years 80% of the Minimum Power (Pmin) 144 Xxxxx Note: Maximum Power (Pmax) and Minimum Power (Pmin) are measured under Standard Test Conditions (STC) 1000W/m2, Cell Temperature 25ºC, Air Mass 1.5. Note: Minimum Power (Pmin) = 90% of Maximum Power at the time of purchase.
Limited Power Output Warranty. SANYO warrants the power output degradation will not fall under 80% of the designated Minimum Power (Pmin) output shown below in Table 1 from date of Product purchase by the Customer. Upon receipt of a Power Output warranty claim, SANYO or its designated representative shall conduct measurements to determine the actual power output of the Product. SANYO’s measurement shall be the sole determination for purposes of warranty settlement. If SANYO measures power loss under the warranted level and such power loss is the result of a product defect, as determined by SANYO in its sole and absolute discretion, SANYO will supplement the power output deficiency using one of the following Limited Warranty Remedies. Table 1. Limited Power Output Warranty Period Remarks Example At the Time of Purchase 100% of the Maximum Power (Pmax) stated in Product Data Sheets 240.0 Xxxxx Within 10 Years from Purchase Date 90% of the Minimum Power (Pmin) 205.2 Xxxxx Within 20 Years from Purchase Date 80% of the Minimum Power (Pmin) 182.4 Xxxxx Notes: Maximum Power (Pmax) and Minimum Power (Pmin) are measured under Standard Test Conditions of; Irradiance 1000 W/m2, Cell Temperature 25ºC, and Air Mass 1.5g. The Minimum Power (Pmin) = 95% of Maximum Power (Pmax).
Limited Power Output Warranty. Pixon warrants that the loss of power output for the product shall not exceed the initial guaranteed power which is defined as Peak Power Xxxxx Pmax(Wp) plus Peak Power Xxxxx Pmax(Wp) multiplied by the lower limit of the Power Output Tolerance Pmax(%) – as specified in the relevant Product Degradation Sheet (in section 4) and measured at Standard Test Conditions (STC) and measurement shall either be carried out by Pixon or by a third-party testing institute recognized by Pixon and the Buyer: (According to STC, measurement system uncertainty should be included in all actual power output measurements.) As above, Limited Product Warranty & Limited Power Output Warranty shall be jointly referred to as “Warranties” Power Definitions:
