Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.
CURRENT INVENTORY OF QUALIFIED PROPERTY In addition to the requirements of Section 10.2 of this Agreement, if there is a material change in the Qualified Property described in EXHIBIT 4, then within 60 days from the date commercial operation begins, the Applicant shall provide to the District, the Comptroller, the Appraisal District or the State Auditor’s Office a specific and detailed description of the tangible personal property, buildings, and/or permanent, nonremovable building components (including any affixed to or incorporated into real property) on the Land to which the value limitation applies including maps or surveys of sufficient detail and description to locate all such described property on the Land.
Supported Initial and Renewal Registration Periods a. Initial registrations of Registered Names (where available according to functional specifications and other requirements) may be made in the registry for terms of up to ten years.
Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.
Additional Products Upon satisfying the minimum order requirements above, Enrolled Affiliate may order Additional Products.
Existing Products 1. Hardware - Title and ownership of Existing Hardware Product shall pass to Authorized User upon Acceptance.
Inventories The Operator shall maintain detailed records of Controllable Material.
Inventory To the extent Inventory held for sale or lease has been produced by any Borrower, it has been and will be produced by such Borrower in accordance with the Federal Fair Labor Standards Act of 1938, as amended, and all rules, regulations and orders thereunder.
Payment for Forest Products Delivered Purchaser agrees to pay the State for delivered forest products at the following rate: $0.00/MBF $250.00/MBF for incorrect species delivery* $20/mbf for Utility logs (Adjusted Gross). Purchaser agrees to increase the above delivered payment rate as approved by the State in the event the location of delivery is changed per the G-026.2 clause. Purchaser will not be billed for any delivered logs that are scaled as containing metal. *When two or more log sorts from this project are delivered to the same destination, the species contained in them are not eligible for the species price reduction. P-036.2 Missorts and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet the sorting specifications in G-022.2 are considered mis-sorts. Purchaser receiving mis-sort Forest Products is required to pay the State at the bid price under this contract. However, when mis-sorted Forest Products amount to more than 5% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-sort threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-sort payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-sort price reduction are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-sorted will be calculated as follows: Payment Reduction = (B x M) x R Where: B = Bid rate from P-028.2 clause M = Mis-sorted volume exceeding threshold excluding utility R = Reduction factor* 0.2 for diameter mis-sort 0.3 for high quality mis-sort *Logs eligible for payment reduction based on multiple reduction factors will be calculated at the higher payment reduction factor. Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-sort payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-sorts shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code P-037.2 Mismanufacture and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet preferred log length specifications or multiples or combinations of preferred lengths and Forest Products delivered not meeting manufacturing standards as described in clause G-024.2 are considered mis- manufactured. Purchaser receiving mis-manufactured Forest Products is required to pay the State at the bid price under this contract. However, when mis-manufactured Forest Products amount to more than 8% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-manufacture threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-manufacture payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-manufacture price reductions are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-manufactured will be calculated as follows: Payment Reduction = (B x M) x (0.2) Where: B = Bid rate from P-028.2 clause M = Mis-manufactured volume exceeding threshold excluding utility Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-manufacture payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-manufacture shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Scaling Lost Products The volume of lost products shall be determined by the best methods currently available, using data from the records for the period in which the loss occurred or the most applicable period if loss should occur substantially after cutting. In the absence of specific information indicating size or species of lost products, species distribution and volume for entire truckloads shall be assumed to be the same as the average volume Scaled per truck during the report period, and for individual products it shall be assumed that the volume and species were the average volume of the highest priced species Scaled during the report period. B6.851 Scaling Lost Sample Loads. If Scal- ing is being done by sampling loads of logs, Purchaser shall present such sample loads for Scaling by Forest Service. If loads of logs selected to be sample Scaled are placed in the decks before they are Scaled, they will be considered as lost sample loads. It will be difficult, if not impossible, to determine the volume and species con- tained in such loads for payment purposes. Therefore, lost sample loads will be deemed to have a Scale volume and species composition equal to that of the highest value load Scaled during the sampling period, as estab- lished by Forest Service. If no sample loads were Scaled during the period, the Scale data for the high valued load will be taken from the most current preceding sampling period with Scale. Sample loads lost as a result of Forest Service actions shall be treated as non-Scaled loads.
