GENERAL INSTALLATION REQUIREMENTS. A. All surfaces shall be adequately anchored, even, and free of any foreign material, moisture, or unevenness.
GENERAL INSTALLATION REQUIREMENTS. Where identification is to be applied to surfaces requiring painting, insulation, or other covering or finish, including valve tags in finished mechanical spaces, install identification after completion of covering and painting. Install identification prior to installation of acoustical ceilings and similar removable concealment.
GENERAL INSTALLATION REQUIREMENTS. For water and sewer crossings under railways, the highest point of carrier pipe shall be below the frost line. In regions of permafrost or where other obstacles make it impossible to place the pipe below the frost line, the applicant will propose alternate methods to protect the pipe in sub-freezing temperatures and shall obtain approval of the Engineer to use such methods. Pipelines carrying steam, water (including oilfield steam and water), sewer and other non-flammable or non-hazardous substances under railways, shall not be placed within culverts nor under railway bridges where there is likelihood of restricting the area required for the purposes for which the culverts or bridges were built, or of endangering the foundations. Any such pipelines laid longitudinally on railway rights-of-way shall be located as far as practicable from any tracks or other important structures. If located within 7.62 metres of the centre-line of any track, or where there is significant risk of damage from leakage to any bridge, building or other important structure, the carrier pipe shall be encased or of special design as approved by the Engineer. Every open drain crossing tracks in a railway yard shall be safely covered for at least 3.0m from the centre-line of track, except in times of flood when uncovered open drains may be provided as may be necessary. In this case warning signs shall be erected.
GENERAL INSTALLATION REQUIREMENTS. A. Install products as specified in individual sections, in accordance with manufacturer's instructions and recommendations to extent that those instructions and recommendations are more explicit or stringent than requirements contained in Contract Documents. Notify Architect of conflicts between Manufacturer's installation instructions and Contract Document requirements.
GENERAL INSTALLATION REQUIREMENTS. This section identifies the basic requirements for a wi-fi antenna installation on a distribution or streetlight pole. For further detail on installation requirements, see the PacifiCorp Distri- bution Construction Standards, EU—Joint Use.
GENERAL INSTALLATION REQUIREMENTS. A Install products as specified in individual sections, in accordance with manufacturer's instructions and recommendations, and so as to avoid waste due to necessity for replacement. B Make vertical elements plumb and horizontal elements level, unless otherwise indicated. C Install equipment and fittings plumb and level, neatly aligned with adjacent vertical and horizontal lines, unless otherwise indicated. D Make consistent texture on surfaces, with seamless transitions, unless otherwise indicated. E Make neat transitions between different surfaces, maintaining texture and appearance.
GENERAL INSTALLATION REQUIREMENTS. A. Cooperate with manufacturer, inspection and test agencies engaged or required to perform services in connection with installing modified bitumen roofing system.
GENERAL INSTALLATION REQUIREMENTS. A. Coordinate ordering and installation of all equipment with long lead times or having a major impact on work by other trades so as not to delay the job or impact the schedule.
GENERAL INSTALLATION REQUIREMENTS. Air Conditioning Sleeve: new sleeves shall be Type A or B by Friedrich Air Conditioning Co. The Sleeves shall be 27” wide by 16 -3/4” high. Except as otherwise indicated, comply with manufacturer’s installation instructions and recommendations, and with SMACNA “Architectural Sheet Metal Manual”. Anchor units of work securely in place by methods indicated, providing for thermal expansion of metal units; conceal fasteners where possible and set units true to line and level as indicated. Install work with laps, joints and seams that will be permanently watertight and weatherproof. Contractor shall be responsible for the protection of all surfaces below the area of demolition. Where public access may be possible the Contractor shall post warning signs and caution tape. The work will only be allowed at times that are convenient to the building staff and meet the requirements of the Alteration Agreement. Demolish interior and exterior masonry only as required for the installation of the new sleeve. New masonry shall be toothed into existing adjacent masonry and existing coursing shall be matched. If openings are to be left open overnight, the opening shall be protected and waterproofed temporarily. Remove all face and back-up masonry necessary for the installation of new sleeves and related flashing. New sleeves shall be mounted directly below the existing xxxxx. No masonry will be allowed between the bottom of the sill and the top of the sleeve. If the sleeve is to be located below a joint in the existing sill, the installation of a lintel will be required. The new lintel shall bear on the adjacent masonry a minimum of 8”. Louvers/grilles will be aluminum. Grills and the bolts and screws used in their installation shall be of noncorrosive material so as to prevent any staining of the Building by corrosion. The installation, including electrical wiring, shall be in accordance with the requirements of the Corporations Managing Agent and public agencies or authorities having or asserting jurisdiction. Units shall not project beyond the building façade and they shall be in line with other units already installed. The Shareholder must notify and insure, at least five (5) days prior to the commencement of work, all apartments in the vicinity of the premises (up, down and adjacent) in order to allow the residents to close their windows and cover their air conditioning units. The shareholder takes full responsibility for the quality (including noise transmission) and a...
GENERAL INSTALLATION REQUIREMENTS. 1. Inspect locations where components are to be installed and ensure suitability of mounting surfaces and conditions prior to installation.
