Form Ties Sample Clauses

Form Ties. Embedded metal rods or sleeves used for holding forms shall remain embedded and shall terminate not less than 2½ cm from the face of the concrete. Embedded wire ties for holding forms will not be permitted in concrete walls which are to come into contact with liquids or where the concrete surfaces through which the ties would extend will be permanently exposed. Wire ties may be used for concrete walls to be plastered, stone faced or covered with earth. Wire ties shall be cut back at least 1.5 cm from the face of the concrete. The holes left in the concrete surfaces after cutting back of wire ties and removal of fasteners or holding rods or sleeves, and the insides of sleeves where sleeves are used, shall be completely filled with an approved non-shrinking mortar, and the mortar shall be finished flush with the concrete surfaces. This operation will be carefully carried out. The hole formed by the cutting process will be thoroughly cleaned and wetted before filling. Time mortar will be of damp, not wet, consistency. The patch will be properly towelled smooth to match the surrounding concrete surfaces and shall be thoroughly cured by keeping it moist continuously for at least three days. After the patch has hardened, the Engineer may require the patch and the adjacent concrete surface to be ground down smooth. Any patches that are loose or hollow on completion must be re-done. Water stop tie rods shall be used for liquid retaining structures. All costs for complying with the requirements of this Subsection shall be deemed to be included in the unit rates for formwork and shall not be paid for separately.
AutoNDA by SimpleDocs
Form Ties. Factory-fabricated, removable or snap-off metal or glass-fiber-reinforced plastic form ties designed to resist lateral pressure of fresh concrete on forms and to prevent spalling of concrete on removal.
Form Ties. Factory-fabricated, internally disconnecting ties designed to resist lateral pressure of fresh concrete on forms and to prevent spalling of concrete on removal.
Form Ties. Forms ties shall be of the removable or permanently embedded body type, and shall have sufficient strength and rigidity to support and maintain the form in proper position and alignment without the use of auxiliary spreaders. Cones, for the permanent embedded type shall be provided on the outer ends of each tie and the permanently embedded portion shall be at least 25mm back from adjacent outer concrete faces shall not be nearer the surface than the specified thickness of cover to the reinforcement. Form ties for indirect tutch with water walls, shall be provided with waterseal washers located on the permanently embedded portions of form ties, and approximately at the centre of the wall. Permanently embedded portions of form ties, which are not provided with threaded ends, shall be constructed so that the removable ends are readily broken off without damage to the concrete. The type of form ties used shall be acceptable to the Engineer. Form ties in exposed surface shall be uniformly spaced and aligned in horizontal and vertical rows.

Related to Form Ties

  • RISK DISCLOSURE STATEMENTS 37.1 Risk of Securities trading The prices of Securities fluctuate, sometimes dramatically. The price of a security may move up or down, and may become valueless. It is as likely that losses will be incurred rather than profit made as a result of buying and selling Securities.

  • Antitrust Certification Statements (Tex Government Code § 2155.005) By submission of this bid or proposal, the Bidder certifies that: I affirm under penalty of perjury of the laws of the State of Texas that: (1) I am duly authorized to execute this contract on my own behalf or on behalf of the company, corporation, firm, partnership or individual (Company) listed below; (2) In connection with this bid, neither I nor any representative of the Company has violated any provision of the Texas Free Enterprise and Antitrust Act, Tex. Bus. & Comm. Code Chapter 15; (3) In connection with this bid, neither I nor any representative of the Company has violated any federal antitrust law; (4) Neither I nor any representative of the Company has directly or indirectly communicated any of the contents of this bid to a competitor of the Company or any other company, corporation, firm, partnership or individual engaged in the same line of business as the Company.

  • Certificate of Interested Parties Form – Form 1295 As required by Section 2252.908 of the Texas Government Code. H-GAC will not enter a Contract with Contractor unless (i) the Contractor submits a disclosure of interested parties form to H-GAC at the time the Contractor submits the contract H-GAC, or

  • Form 700 Filing The California Political Reform Act and the Chula Vista Conflict of Interest Code require certain government officials and consultants performing work for government agencies to publicly disclose certain of their personal assets and income using a Statement of Economic Interests form (Form 700). In order to assure compliance with these requirements, Consultant shall comply with the disclosure requirements identified in the attached Exhibit C, incorporated into the Agreement by this reference.

  • Risk Disclosure Statement Counterparty represents and warrants that it has received, read and understands the OTC Options Risk Disclosure Statement provided by Dealer and a copy of the most recent disclosure pamphlet prepared by The Options Clearing Corporation entitled “Characteristics and Risks of Standardized Options”.

  • CERTIFICATION STATEMENT Under Section 231.006, Family Code, the vendor or applicant certifies that the individual or business entity named in this contract, bid, or application is not ineligible to receive the specified grant, loan, or payment and acknowledges that this contract may be terminated and payment may be withheld if this certification is inaccurate. The contractor understands that it is the contractor’s responsibility to verify whether a child support obligor who is more than 30 days delinquent is the sole proprietor, partner, shareholder or owner with an ownership interest of at least 25%.

  • Interest Questionnaire - Form CIQ No response Do not upload this form unless you have a reportable conflict with TIPS. There is an Attribute entitled “Conflict of Interest Questionnaire Requirement” immediately followed by an Attribute entitled “Conflict of Interest Questionnaire Requirement – Form CIQ – Continued.” Properly respond to those Attributes and only upload this form if applicable/instructed. If upload is required based on your response to those Attributes, the Conflict of Interest Questionnaire – Form CIQ must be downloaded from the “Attachments” section of the IonWave eBid System, reviewed, properly completed, and uploaded at this location. Vendor’s Warranties, Terms, and Conditions (Supplemental Vendor Information Only)

  • Disclosure Statement for Xxxx IRAs 1. Am I Eligible to Contribute to a Xxxx XXX? Anyone with compensation income whose Modified Adjusted Gross Income (AGI) does not exceed the limits described below is eligible to contribute to a Xxxx XXX. (For convenience, all future references to compensation are deemed to mean “earned income” in the case of a self- employed individual.) Employers may also contribute to Xxxx IRAs established for the benefit of their employees. You may also establish a Xxxx XXX to receive rollover contributions or transfers from another Xxxx XXX or, in some cases, from a Traditional IRA. A Qualified Rollover Contribution can be made to a Xxxx XXX and is a distribution from an IRA that meets the requirements of section 408(d)(3), a rollover from a designated Xxxx account described in section 402A, or a rollover from an eligible retirement plan as described in section 402(c)(8)(B).

  • Transfer Documents In furtherance of the contribution, assignment, transfer, conveyance and delivery of the Assets and the assumption of the Liabilities in accordance with Section 2.1(a), (i) each Party shall execute and deliver, and shall cause the applicable members of its Group to execute and deliver, to the other Party, such bills of sale, quitclaim deeds, stock powers, certificates of title, assignments of contracts and other instruments of transfer, conveyance and assignment as and to the extent necessary to evidence the transfer, conveyance and assignment of all of such Party’s and the applicable members of its Group’s right, title and interest in and to such Assets to the other Party and the applicable members of its Group in accordance with Section 2.1(a), and (ii) each Party shall execute and deliver, and shall cause the applicable members of its Group to execute and deliver, to the other Party, such assumptions of contracts and other instruments of assumption as and to the extent necessary to evidence the valid and effective assumption of the Liabilities by such Party and the applicable members of its Group in accordance with Section 2.1(a). All of the foregoing documents contemplated by this Section 2.1(b) shall be referred to collectively herein as the “Transfer Documents.”

  • Conflict of Interest Questionnaire - Form CIQ No response Do not upload this form unless you have a reportable conflict with TIPS. There is an Attribute entitled “Conflict of Interest Questionnaire Requirement” immediately followed by an Attribute entitled “Conflict of Interest Questionnaire Requirement – Form CIQ – Continued.” Properly respond to those Attributes and only upload this form if applicable/instructed. If upload is required based on your response to those Attributes, the Conflict of Interest Questionnaire – Form CIQ must be downloaded from the “Attachments” section of the IonWave eBid System, reviewed, properly completed, and uploaded at this location. Vendor’s Warranties, Terms, and Conditions (Supplemental Vendor Information Only)

Time is Money Join Law Insider Premium to draft better contracts faster.