Flow and Tamper Devices a. Visually inspect for damage
Flow and Tamper Devices b. Test by opening the inspection test valve on the sprinkler system (Retard should be 90 seconds or less)
Flow and Tamper Devices Sample Clauses
Related to Flow and Tamper Devices
Access to Network Interface Device (NID 2.4.3.1. Due to the wide variety of NIDs utilized by BellSouth (based on subscriber size and environmental considerations), Mpower may access the on-premises wiring by any of the following means: BellSouth shall allow Mpower to connect its loops directly to BellSouth’s multi-line residential NID enclosures that have additional space and are not used by BellSouth or any other telecommunications carriers to provide service to the premise. Mpower agrees to install compatible protectors and test jacks and to maintain the protection system and equipment and to indemnify BellSouth pursuant to Section 8 of the General Terms and Conditions of this Agreement.
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
CONTRACTOR PORTABLE DEVICES Contractor shall not place Data on any portable Device unless Device is located and remains within Contractor’s CONUS Data Center. For Authorized Users subject to ITS policies, the Data, and/or the portable device containing the Data, shall be destroyed in accordance with applicable ITS destruction policies (ITS Policy S13-003 Sanitization/Secure Disposal and S14-003 Information Security Controls or successor) when the Contractor is no longer contractually required to store the Data. TRANSFERRING OF DATA General Except as required for reliability, performance, security, or availability of the services, the Contractor will not transfer Data unless directed to do so in writing by the Authorized User. All Data shall remain in CONUS. At the request of the Authorized User, the Contractor will provide the services required to transfer Data from existing Databases to physical storage devices, to facilitate movement of large volumes of Data. The Authorized User may require several Cloud providers to share or transfer Data for a period of time. This will be provided for in the Authorized User Agreement or shall be assumed to be limited to a six month duration. Transfer of Data at End of Contract and/or Authorized User Agreement Term At the end of the Contract and/or Authorized User Agreement term, Contractor may be required to facilitate transfer of Data to a new Contractor. This transfer must be carried out as specified by the Authorized User in the Authorized User Agreement. Transfer of Data; Charges Contractor cannot charge for the transfer of Data unless the charges are provided for in response to an Authorized User RFQ. Transfer of Data; Contract Breach or Termination Notwithstanding Section 3.6.3, in the case of Contract breach or termination for cause of the Contract, all expenses for the transfer of Data shall be the responsibility of the Contractor.
Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.
Labelling The distributor, on behalf of the selected vendor agrees that all supplies of articles should invariably contain the following information on its label and the carton. One information should not be overlapped by any other information needed to be furnished. The label should contain :
EODUF Packing Specifications 7.3.1 The data will be packed using ATIS EMI records. A pack will contain a minimum of one (1) message record or a maximum of ninety-nine thousand nine hundred and ninety-nine (99,999) message records plus a pack header record and a pack trailer record. One transmission can contain a maximum of ninety-nine (99) packs and a minimum of one (1) pack.
Network Interface Device (NID) 2.7.1 The NID is defined as any means of interconnection of end-user customer premises wiring to BellSouth’s distribution plant, such as a cross-connect device used for that purpose. The NID is a single-line termination device or that portion of a multiple-line termination device required to terminate a single line or circuit at the premises. The NID features two independent xxxxxxxx or divisions that separate the service provider’s network from the end user’s customer-premises wiring. Each chamber or division contains the appropriate connection points or posts to which the service provider and the end user each make their connections. The NID provides a protective ground connection and is capable of terminating cables such as twisted pair cable.
For Product Development Projects and Project Demonstrations Published documents, including date, title, and periodical name. Estimated or actual energy and cost savings, and estimated statewide energy savings once market potential has been realized. Identify all assumptions used in the estimates. Greenhouse gas and criteria emissions reductions. Other non-energy benefits such as reliability, public safety, lower operational cost, environmental improvement, indoor environmental quality, and societal benefits. Data on potential job creation, market potential, economic development, and increased state revenue as a result of the project. A discussion of project product downloads from websites, and publications in technical journals. A comparison of project expectations and performance. Discuss whether the goals and objectives of the Agreement have been met and what improvements are needed, if any.
Technical Specification As enumerated in Special Conditions of Contract/Scope of Work/attached Drawing/ Details/Schedule of Rates.
Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. Items Offered as New. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.
