Electric Metering Devices. (a) Facility Energy shall be measured using a CAISO-approved revenue- quality Electric Metering Device at the Facility that complies with the CAISO Tariff and relevant protocols and is dedicated exclusively to the Facility. Seller shall arrange and bear all costs associated with the installation of the Electric Metering Devices needed for the registration, recording and transmission of information regarding the Energy generated at the Facility. Seller shall provide, or cause to be provided, to Buyers’ Agent a mutually agreed set of meter data, which data shall be accessible to, and usable by, Buyers. In addition to providing Buyers’ Agent with its meter data, Seller shall use commercially reasonable efforts to support any efforts by Buyers’ Agent to obtain CAISO meter data applicable to the Facility and all inspection, testing and calibration data and reports from CAISO. If the CAISO makes any adjustment to any meter data for a given time period, Seller agrees that it shall submit revised Monthly invoices, pursuant to this Article X covering the entire applicable time period in order to fully conform such adjustments to the meter data. Seller shall submit any revised invoices no later than thirty (30) days after the date on which the CAISO provides Seller with binding adjustments to the meter data. To the extent consistent with the requirements of the CAISO, all Electric Metering Devices used to provide data for the computation of payments shall be sealed and Seller or its designee shall only break the seal when such Electric Metering Devices are to be inspected and tested or adjusted in accordance with this Section 10.6. Seller or its designee shall specify the number, type, and location of such Electric Metering Devices.
Electric Metering Devices. (a) Delivered Energy shall be measured using Electric Metering Devices installed, owned and maintained by the Seller and its Affiliates. If the Electric Metering Devices are not installed at a Point of Delivery, meters or meter readings shall be adjusted to reflect losses from the Electric Metering Devices to such Point of Delivery. To the extent consistent with the requirements of the Transmission Provider, all Electric Metering Devices used to provide data for the computation of payments shall be sealed and Seller or its designee shall only break the seal when such Electric Metering Devices are to be inspected and tested or adjusted in accordance with this Section 11.6. Seller or its designee shall specify the number, type, and location of such Electric Metering Devices.
Electric Metering Devices. With respect to this Section 5.3, and notwithstanding the general applicability of the interpretive provisions of Section 1.2(B), the metering provisions of the Interconnection Agreement (including Article 7 thereof) are incorporated herein by reference and Buyers agree that Seller shall retain all of its rights thereunder without regard to any separateness of Buyers and the Interconnection Provider. Accordingly, electric metering shall be in compliance with the Interconnection Agreement. Seller will grant Buyers access to all metering data and other meter information, including testing, on same basis as available to Seller.
Electric Metering Devices. Seller will comply with the terms and conditions of the Interconnection Agreement. The following provisions on Electric Metering Devices shall apply only to the extent they do not conflict with the applicable provisions of the Interconnection Agreement or the Transmission Tariff, as applicable.
Electric Metering Devices. (A) All Electric Metering Devices used to measure Energy shall be owned, installed, and maintained in accordance with the Interconnection Agreement.
Electric Metering Devices. Electric Metering Devices shall be installed in order to separately meter Solar Energy and Natural Gas Generated Energy generated by the Facility. All Electric Metering Devices used to measure energy shall be owned, installed, and maintained in accordance with the Interconnection Agreement at no cost to Company. Meter readings will be adjusted to reflect losses from the Electric Metering Devices to the Point of Delivery in accordance with applicable manufacturers’ parameters or as otherwise agreed by the Parties. Seller shall arrange any necessary authorization to provide Company access to all Electric Metering Devices for purposes of administering this PPA and shall provide Company the opportunity to be present at any time when such Electric Metering Devices are to be inspected, tested or adjusted. Either Party may elect to install and maintain, at its own expense, backup metering devices (“Back-Up Metering”), provided, however, that the specifications, installation and testing of any such Back-Up Metering shall be consistent with the requirements for the Electric Metering Devices. Upon written request from the other Party, the installing Party shall test the Back-Up Metering. The actual cost of any such test shall be borne by the Party requesting the test, unless, upon such test, Back-Up Metering is inaccurate by more than one percent, in which case the cost of the retest shall be borne by the installing Party. If requested in writing, the installing Party shall provide copies of any inspection or testing reports to the requesting Party. If an Electric Metering Device or Back-Up Metering, fails to register, or if the measurement is inaccurate by more than one percent, an adjustment shall be made correcting all measurements as follows: If the Electric Metering Device is found to be defective or inaccurate, the Parties shall use Back-up Metering, if installed, to determine the amount of such inaccuracy, provided, however, Back-Up Metering has been tested and maintained and adjusted for losses on the same basis as the Electric Metering Device. If Back-Up Metering is not installed, or Back-Up Metering is also found to be inaccurate by more than one percent, the Parties shall use the best available information for the period of inaccuracy, adjusted for losses to the Point of Delivery, in accordance with applicable manufacturers’ parameters or as otherwise agreed by the Parties If the Parties cannot agree on the actual period during which the inaccurate measur...
Electric Metering Devices. (A) The following provisions of this Section shall govern Electric Metering Devices except to the extent the Interconnection Agreement modifies or otherwise conflicts with these provisions.
Electric Metering Devices. The following provisions on Electric Metering Devices shall apply only to the extent they do not conflict with requirements of RREC, if it is the owner or operator of the Electric Metering Devices. Seller shall make all reasonable efforts to ensure that RREC requirements are consistent herewith.
Electric Metering Devices. 4.1.1 Except as provided in Section 5.1.3, as between the Parties, Seller shall be responsible for installing and monitoring all Electric Metering Devices used to measure Energy sold by Seller to Buyer under this Agreement and to monitor and coordinate operation of each Facility. Except as provided in Section 5.2, readings of the Electric Metering Devices shall be conclusive as to the amount of Energy sold by Seller to Buyer under this Agreement. All Electric Metering Devices used to provide data for the computation of payments shall be sealed and only Seller, or Seller’s designee, shall break the seal when such Electric Metering Devices are to be inspected and tested or adjusted in accordance with this Article.
Electric Metering Devices. (a) The Delivered Energy and Facility Metered Output made available to Buyer, or Buyer’s Agent, by Seller under this Agreement shall be measured using the Electric Metering Devices installed, owned and maintained by the Seller or its designee in accordance with the Interconnection Agreement, if applicable, and Prudent Utility Practices. If Electric Metering Devices are not installed at the Point of Delivery, meters or meter readings will be adjusted to reflect losses from the Electric Metering Devices to the Point of Delivery. All Electric Metering Devices used to provide data for the computation of payments shall be sealed and the Seller or its designee shall only break the seal when such Electric Metering Devices are to be inspected and tested or adjusted in accordance with this Section 8.4. Seller or its designee shall specify the number, type, and location of such Electric Metering Devices.
