API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.
Manufacturing Technology Transfer With respect to each Technology Transfer Product, upon AbbVie’s written request after the Inclusion Date for the Included Target to which such Technology Transfer Product is Directed, Morphic shall effect a full transfer to AbbVie or its designee (which designee may be an Affiliate or a Third Party manufacturer) of all Morphic Know-How and Joint Know-How relating to the then-current process for the Manufacture of such Technology Transfer Product (the “Manufacturing Process”) and to implement the Manufacturing Process at facilities designated by AbbVie (such transfer and implementation, as more fully described in this Section 5.3, the “Manufacturing Technology Transfer”). To assist with the Manufacturing Technology Transfer, Morphic will make its personnel reasonably available to AbbVie during normal business hours for up to [***] FTE hours with respect to each Included Target (in each case, free of charge to AbbVie) to transfer and implement the Manufacturing Process under this Section 5.3. Thereafter, if requested by AbbVie, Morphic shall continue to perform such obligations; provided, that AbbVie will reimburse Morphic for its full-time equivalent (FTE) costs (for clarity, in excess of [***] FTE hours) and any reasonable and verifiable out-of-pocket costs incurred in providing such assistance. CERTAIN CONFIDENTIAL INFORMATION CONTAINED IN THIS DOCUMENT, MARKED BY [***], HAS BEEN OMITTED BECAUSE IT IS NOT MATERIAL AND WOULD LIKELY CAUSE COMPETITIVE HARM TO THE COMPANY IF PUBLICLY DISCLOSED.
Manufacture of Product Prior to commercialization of the Product, the Parties may, if appropriate for both parties, negotiate in good faith a manufacturing and supply agreement to provide for Licensor to fulfill the manufacturing requirements of Licensee for Product for sale in the European market. The cost of such manufacturing shall not be greater than * percent (*%) of the cost of any competitor cGMP contract manufacturing facility that proposes to manufacturer the Product for Licensee. * Confidential information has been omitted and filed confidentially with the Securities and Exchange Commission.
Royalty Stacking If COMPANY or an AFFILIATE or SUBLICENSEE is legally required to pay royalties to one or more third parties, in order to obtain a license or similar right necessary to practice the PATENT RIGHTS, and COMPANY, AFFILIATE or SUBLICENSEE actually pays said third party royalties, COMPANY may offset a total of **** of such third-party payments against any royalty payments that are due to THE PARTIES in the same REPORTING PERIOD; provided, however, that in no event shall the royalty payments under this section, when aggregated with any other offsets and credits allowed under the AGREEMENT, be reduced below **** of the running royalty for such a LICENSED PRODUCT, DISCOVERY PRODUCT and/or THERAPEUTIC PRODUCT in any REPORTING PERIOD; provided, further, that COMPANY also make best efforts to require such third parties to offset its royalties as a result of royalties payable to THE PARTIES for the Patent RIGHTS by at least the same amount as THE PARTIES has offset its royalties under this Section. For purposes of clarity, third parties may include THE PARTIES.
New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.
Licensed Product “Licensed Product” shall mean any article, composition, apparatus, substance, chemical material, method, process or service whose manufacture, use, or sale is covered or claimed by a Valid Claim within the Patent Rights. For clarity, a “Licensed Product” shall not include other product or material that (a) is used in combination with Licensed Product, and (b) does not constitute an article, composition, apparatus, substance, chemical material, method, process or service whose manufacture, use, or sale is covered or claimed by a Valid Claim within the Patent Rights.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
Manufacture of Products All Products marketed through Grantor's Web ------------------------- Site shall be manufactured, packaged, prepared, and shipped in accordance with the specifications and requirements described on Exhibit A hereto as it may be modified from time to time. Quality control standards relating to the Product's weight, color, consistency, micro-biological content, labeling and packaging are also set forth on Exhibit A. In the event that Exhibit A is incomplete, Products shall be manufactured and shipped in accordance with industry standards.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
Licensed Products Lessee will obtain no title to Licensed Products which will at all times remain the property of the owner of the Licensed Products. A license from the owner may be required and it is Lessee's responsibility to obtain any required license before the use of the Licensed Products. Lessee agrees to treat the Licensed Products as confidential information of the owner, to observe all copyright restrictions, and not to reproduce or sell the Licensed Products.
