Concrete Placement Sample Clauses

Concrete Placement. 4.8.4 Structural steel prior to being enclosed or covered.
Sample 1
AutoNDA by SimpleDocs
Concrete Placement. The concrete shall not be placed until the sub-grade has been inspected for compaction and moisture. The concrete shall be compacted with an approved internal type vibrator, or by hand spudding and tamping. The surface shall be shaped by use of a steel tool to produce the sections shown on the drawings. The edges shall be rounded with edgers to form the radii as directed by the Engineer. The surfaces shall be finished with a wooden or metallic float and brushed. All concrete shall be cured in accordance with the Overland Park Municipal Code.
Sample 1
Concrete Placement. Deposit concrete only in the presence of and by methods approved by the Department. Ensure all reinforcement is free of dirt, loose rust, grease, and other deleterious substances. Accurately place all items to be encased in the concrete in the position shown on the Plans and firmly held during the placing and setting of the concrete. Vibrate concrete either internally or externally, or both, as required. The RE will approve the type, number, and method of application of vibrators. Apply internal vibrations to the concrete for time intervals of approximately ten seconds and at points not more than 18 inches apart. Do not use vibrators to move concrete horizontally in the form. Do not displace any reinforcement inserts with the vibrating. Ensure form liners, where required, do not leak at the joints and ensure seams are fused according to the manufacturer’s recommendations. No unfused seams will be permitted. The placement of seams will be subject to the approval of the RE. Place form liner seams so that the architectural finish will be unbroken and continuous. Ensure precast concrete posts and panels are free of honeycombing or voids and be true to size and dimensions within the following limits:
Sample 1
Concrete Placement. A. Pile concrete shall be placed immediately after the completion of drilling and inspection of the pile hole and the placement of reinforcing steel.
Sample 1
Concrete Placement. A. Under no circumstances shall the pile holes be left open for periods longer than 2 hours.
Sample 1
Concrete Placement. Concrete shall be deposited only by approved methods. All reinforcement shall be free of dirt, loose rust, grease, and other deleterious substances. All items to be encased in the concrete shall be accurately placed in the position shown on the Plans and firmly held during the placing and setting of the concrete. Concrete shall be vibrated internally or externally, or both, as required. Internal vibrations shall be applied to the concrete for time intervals of approximately ten seconds and at points not more than 18 inches apart. Vibrators shall not be used to move concrete horizontally in the form. The vibrating shall not displace any reinforcement inserts. Form liners, where required, shall not leak at the joints and seams must be fused according to the manufacturer’s recommendations. No unfused seams will be permitted. The placement of seams will be subject to the approval of the Engineer. Form liner seams shall be placed so that the architectural finish will be unbroken and continuous. Precast concrete units shall be free of honeycombing or voids and shall be true to size and dimensions within the following limits:
Sample 1
Concrete Placement. Deposit concrete only in the presence of and by methods approved by the Department. Ensure all reinforcement is free of dirt, loose rust, grease, and other deleterious substances. Accurately place all items to be encased in the concrete in the position shown on the Plans and firmly held during the placing and setting of the concrete.
Sample 1
AutoNDA by SimpleDocs
Concrete Placement. A. Before placing concrete, verify that installation of formwork, reinforcement, and embedded items is complete and that required inspections have been performed.
Sample 1
Concrete Placement. During the pours, the CONSULTANT shall be on site continuously, as required by code, to monitor placement. The CONSULTANT shall:
Sample 1

Related to Concrete Placement

  • Step Placement A. Employees will be compensated on a salary range consisting of seven (7) steps. The salary percentage differential for the seven (7) steps is as follows:

  • Private Placement Assuming the accuracy of the Purchasers’ representations and warranties set forth in Section 3.2, no registration under the Securities Act is required for the offer and sale of the Securities by the Company to the Purchasers as contemplated hereby. The issuance and sale of the Securities hereunder does not contravene the rules and regulations of the Trading Market.

  • Order Placement To place orders for the Trustee to create or redeem one or more Baskets, Authorized Participants must follow the procedures for creation and redemption referred to in Section 3 of this Agreement and the procedures described in Attachment A hereto (the “Procedures”), as each may be amended, modified or supplemented from time to time.

  • Initial Placement The issuance and sale by the Company of the Notes to the Initial Purchasers pursuant to the Purchase Agreement.

  • PRACTICAL PLACEMENTS 8.1 If a Skills First Student is to undertake a Practical Placement, the Training Provider must enter into a written Practical Placement agreement.

  • Salary Schedule Placement 1. Credit hours for the purpose of placement on the salary schedule shall be defined as those semester hour credits earned for graduate courses that are within the teacher’s present certification or a planned program leading to additional areas of teacher certification, guidance or administration. Upon approval of the Superintendent, any other courses, graduate or undergraduate may be certified for proper placement on the salary schedule.

  • EXCHANGE OF GLOBAL NOTES 4.1 The Agent shall determine the Exchange Date for each Temporary Global Note in accordance with its terms. Immediately after determining any Exchange Date, the Agent shall notify its determination to the Issuer, the other Paying Agents, the relevant Dealer, Euroclear and Clearstream, Luxembourg.

  • Shipping must be Freight On Board Destination to the delivery location designated on the Customer purchase order The Contractor will retain title and control of all goods until delivery is completed and the Customer has accepted the delivery. All risk of transportation and all related charges are the responsibility of the Contractor. The Customer will notify the Contractor and H-GAC promptly of any damaged goods and will assist the Contractor in arranging for inspection. The Contractor must file all claims for visible or concealed damage. Unless otherwise stated in the Agreement, deliveries must consist only of new and unused merchandise.

  • Scope and Order Placement These terms may be used by Customer either for a single Order or as a framework for multiple Orders. In addition, these terms may be used on a global basis by the parties’ “Affiliates”, meaning any entity controlled by, controlling, or under common control with a party. The parties can confirm their agreement to these terms either by signature where indicated at the end or by referencing these terms on Orders. Affiliates participate under these terms by placing orders which specify product or service delivery in the same country as the HP Affiliate accepting the Order, referencing these terms, and specifying any additional terms or amendments to reflect local law or business practices.

  • ROAD DIMENSIONS Purchaser shall perform road work in accordance with the dimensions shown on the TYPICAL SECTION SHEET and the specifications within this road plan.

Time is Money Join Law Insider Premium to draft better contracts faster.