Design and Construction In complying with the requirements of the specification both with respect to arrangement and detail, design is to conform to the best current engineering practice. Each of the several parts of the material is to be of the maker’s standard design provided that this design is in general accordance with the specification. The essence of design should be simplicity and reliability in order to give long continuous service with high economy and low maintenance cost. Particular attention should be paid to internal and external access in order to facilitate inspection, cleaning and maintenance. The design dimensions and materials of all parts are to be such that they will not suffer damage as a result of stresses under the most severe conditions. Fully detailed specifications of the several parts of the material are to be submitted describing particularly the materials to be used. The materials used in the construction of the material are to be of the highest quality and selected particularly to meet the duties required of them. Mechanisms are to be constructed to avoid sticking due to rust or corrosion. Workmanship and general finish are to be of the highest class throughout. All similar parts of the material are to be interchangeable. All equipment is to operate without undue vibration and with the least possible amount of noise and is not to cause a nuisance. All equipment is to be designed to minimize the risk of fire and any damage, which may be caused in the event of fire. The equipment is also to be designed to prevent ingress of all vermin, accidental contact with live parts and to minimize the ingress of dust and dirt. The use of materials, which may be liable to attack by termites or other insects, is to be avoided.
Coordination of Design and Construction Contract Documents 5.5.1 Review model(s), Drawings, Specifications and other Construction Documents as they are developed by A/E during the Schematic Design, Design Development, and Construction Documents design phases of the Project.
SUPERVISION AND CONSTRUCTION PROCEDURES 4.3.1 The Contractor shall supervise and direct the Work, using his / her best skill and attention. The Contractor shall be solely responsible for all construction means, methods, techniques, sequences and procedures and for coordinating all portions of the Work under the Contract. All aspects of the Project shall be subject to the inspection and approval of the State. Contractor guarantees to repair, replace, re-execute or otherwise correct any defect in workmanship, materials, or the like that fails to conform to the requirements of this Contract or that appears during the progress of the Work or within one year of final acceptance by the State.
Suspension of unsafe Construction Works (i) Upon recommendation of the Authority’s Engineer to this effect, the Authority may by notice require the Contractor to suspend forthwith the whole or any part of the Works if, in the reasonable opinion of the Authority’s Engineer, such work threatens the safety of the Users and pedestrians.
Compliance with Laws, Rules and Regulations Tenant, at its sole cost and expense, shall comply with all laws, ordinances, orders, rules and regulations of state, federal, municipal, or other agencies or bodies having jurisdiction over use, condition, and occupancy of the Leased Premises. Tenant must use and maintain the Leased Premises in a clean, careful, safe, and proper manner and in compliance with all Applicable Laws, including Applicable Laws pertaining to health, safety, disabled persons, and the environment; provided, however, that Tenant shall not be required to make any structural changes or repairs to the Leased Premises unless the need for such structural changes or repairs is caused by Tenant, its agents, employees, invitees, or others for whom Tenant is responsible pursuant to the terms and provisions of this Lease. Notwithstanding anything to the contrary contained elsewhere in this section, it is expressly agreed and understood that Tenant’s obligation to comply with all Applicable Laws does not apply to any violations of Applicable Laws that (a) were in effect and (b) were being violated or with which the Leased Premises was not in compliance immediately prior to the time Tenant accepted the Leased Premises, including without limitation any existing environmental contamination. Tenant will comply with the rules and regulations of the Leased Premises adopted by Landlord in its reasonable discretion. All such rules and regulations and changes and amendments thereto will be sent by Landlord to Tenant in writing and shall thereafter be carried out and observed by Tenant.
Compliance with Rules and Regulations PFPC undertakes to comply with all applicable requirements of the Securities Laws and any laws, rules and regulations of governmental authorities having jurisdiction with respect to the duties to be performed by PFPC hereunder. Except as specifically set forth herein, PFPC assumes no responsibility for such compliance by the Fund or any other entity.
Construction Standards The Subrecipient and Developer shall ensure that all Approved Projects comply with the following requirements:
Project Construction The Contractor agrees to provide continuous on-site supervision on each Job Order, while progress on the project is being accomplished. The Contractor’s Project Manager will ensure:
Design Criteria and Standards All PROJECTS/SERVICES shall be performed in accordance with instructions, criteria and standards set forth by the DIRECTOR.
Construction Safety Prior to contract award, the successful bidder must provide a Certificate of Recognition or Letter of Good Standing issued by an occupational health and safety organization approved by the Workers’ Compensation Board of Nova Scotia.
