Calibration Requirements Sample Clauses

Calibration Requirements. Calibration requirements are outlined in the applicable Production QC Plan documents included in the Quality and Test Procedures. Jabil shall be responsible for development of implementation and maintenance plans to comply with all such calibration requirements.
Sample 1Sample 2Sample 3See All (5)
AutoNDA by SimpleDocs
Calibration Requirements. Shell shall ensure that the Owner will provide current calibration records and/or factory certifications, traceable to appropriate standards, for all instrumentation critical to the calculation of test results (Class 1 primary variables) in accordance with PTC 46. Calibrations may take place at the Plant Site or at an independent instrumentation laboratory. Permanent Plant thermocouples which are wired to cold junctions in the DCS cabinets will provide “type” measurements and generally will not be calibrated. Calibration laboratories will be certified, traceable to nationally respected standards, and will maintain proper quality assurance procedures. Recalibration of test instruments after the tests will not be required unless, by mutual agreement between the Shell, the Owner and Gulf Power, there is cause for concern regarding instrumentation drift during the testing program.
Sample 1
Calibration Requirements. The Seller shall maintain a system for the calibration of all measuring and test equipment used in fulfillment of the purchase order that is in accordance with ISO 9001 or similar. ADDITIONAL TERMS & CONDITIONS: DEFENSE PRIORITIES AND ALLOCATION SYSTEM (DPAS) RATING: This is a rated contract, certified for national defense. The Seller is required to follow all provisions of the Defense Priorities and Allocation System Regulations (Ref 15 CFR 700). The DPAS Rating of this order is . xxxxx://xxx.xxxx.xxx/current/title-15/subtitle-B/chapter-VII/subchapter-A/part-700 FLOW DOWNS: Seller shall comply with all flow down clauses associated with the prime contract under which this purchase is made. Prime Contract Number: .
Sample 1
Calibration Requirements. All Certificates provide traceability to NIST and meet ANS/NCSL Z540-1 requirements.
Sample 1
Calibration Requirements. The flow rate of the high volume sampler with mass flow controller was calibrated using an orifice calibrator. Initial calibration (five points) was conducted upon installation and prior to commissioning. Calibration was carried out every six months. Calibration certificate is attached in Appendix C. Calibration of the MIE by certified laboratory or manufacturer was carried out every two years and properly documented. Calibration certificate is attached in Appendix C. The samplers shall be properly maintained. Prior to dust monitoring commencing, appropriate checks shall be made to ensure that all equipment and necessary power supply are in good working condition.
Sample 1
Calibration Requirements. Where a Work Order has not been completed, detailed calibration requirements must be specified on your Purchase Order or included with your instrument. This includes the type of service required, any specific data points or function checks and compliance with any specific standards etc. The Customer is responsible for ensuring it orders the required service(s). If you do not supply us with your requirements, RadPro’s default service/procedure will be provided based on the instrument type, make or model. CONFIDENTIALITY: All service requests, orders etc. made by the Customer to RadPro are considered proprietary information for the purposes specified in the Work or Purchase Order. All information furnished by the Customer to RadPro is considered CONFIDENTIAL. REPAIRS: We will advise you if any instruments are found to be in need of repairs and seek your instructions on how you would like us to proceed. The service fees for any repairs you may wish us to make are charged in addition to the calibration fees.
Sample 1
Calibration Requirements. The process for calibrating manufacturing and inspection equipment such as CNC (Computerized Numerical Control) machines, spot welders, ovens, wave solder, verniers, torque tools hardness testers, dielectric strength, DVM's (Digital Voltmeter), ICT (In-Circuit Test), FCT (Functional Card/Component Test) and vibration test equipment, etc. shall be defined and documented by the Supplier. As part of the calibration requirements, Supplier shall maintain records of the equipment calibrated, equipment labeling, calibration processes used, and the frequency of calibration.
Sample 1
AutoNDA by SimpleDocs

Related to Calibration Requirements

  • Encryption Requirements Transfer Agent will not locally store Fund Data on any laptops or mobile devices (e.g., Blackberries, PDAs) managed by Transfer Agent.

  • Construction Requirements a) All Life and Safety and applicable Building Codes will be strictly enforced (i.e., tempered glass, fire dampers, exit signs, smoke detectors, alarms, etc.). Prior coordination with the Building Manager is required.

  • Notification Requirements 1. If the Family Leave is foreseeable, the employee must provide the agency/department with thirty (30) calendar days notice of his or her intent to take Family Leave.

  • Information Requirements (a) The Company covenants that, if at any time before the end of the Effectiveness Period the Company is not subject to the reporting requirements of the Exchange Act, it will cooperate with any Holder of Registrable Securities and take such further reasonable action as any Holder of Registrable Securities may reasonably request in writing (including, without limitation, making such reasonable representations as any such Holder may reasonably request), all to the extent required from time to time to enable such Holder to sell Registrable Securities without registration under the Securities Act within the limitation of the exemptions provided by Rule 144 and Rule 144A under the Securities Act and customarily taken in connection with sales pursuant to such exemptions. Upon the written request of any Holder of Registrable Securities, the Company shall deliver to such Holder a written statement as to whether it has complied with such filing requirements, unless such a statement has been included in the Company's most recent report filed pursuant to Section 13 or Section 15(d) of Exchange Act. Notwithstanding the foregoing, nothing in this Section 7 shall be deemed to require the Company to register any of its securities (other than the Common Stock) under any section of the Exchange Act.

  • Distribution Requirements Arts 3 A course in history, philosophy, theory, or practice of the creative and interpretive arts.

  • Notification Requirement Through and up to the conclusion of the Non-Competition Period, Executive shall give notice to the Company of each new business activity he plans to undertake, at least seven (7) days prior to beginning any such activity. Such notice shall state the name and address of the Person for whom such activity is undertaken and the nature of Executive’s business relationship(s) and position(s) with such Person.

  • Assumption Requirements Any Assumption permitted under this Agreement shall be performed in accordance with Prudent Servicing Practices. In connection with an Assumption of an assumable Mortgage Loan, the Servicer shall process such Assumption as provided for in the Mortgage Note or the Mortgage Note Assumption Rider and shall verify that:

  • Satisfaction Requirement If any agreement, certificate or other writing, or any action taken or to be taken, is by the terms of this Agreement required to be satisfactory to any Purchaser, to any holder of Notes or to the Required Holder(s), the determination of such satisfaction shall be made by such Purchaser, such holder or the Required Holder(s), as the case may be, in the sole and exclusive judgment (exercised in good faith) of the Person or Persons making such determination.

  • Repatriation Requirements The Employee agrees to promptly repatriate proceeds resulting from the sale of Shares acquired under the Program to a foreign currency account at an authorized bank in Russia if legally required at the time Shares are sold and to comply with all applicable local foreign exchange rules and regulations. Neither the Company nor any of its Subsidiaries shall be liable for any fines or penalties resulting from the Employee’s failure to comply with applicable laws.

Time is Money Join Law Insider Premium to draft better contracts faster.