Battery System Sample Clauses

Battery System. The newly proposed recloser shall be equipped by Interconnection Customer with integral, manufacturer-provided batteries for open and closing energy. However, the remainder of the battery support throughout the entire electrical generation and relaying systems throughout the plant shall be provided in detail, along with alarm drawings and an explanation of the various alarms and the conditions by which they alarm. Relay power and tripping power is required to be from a DC source. The AC source for battery power is typically required to be powered from a source located on the utility side of the customer high side three phase interrupting device. The design of the facility is to be such that it incorporates fail safe provisions to provide for tripping the generation from the EPS for loss or degradation of DC to protective relays, loss of protective relay power supplies, and loss or degradation of tripping power to the required interrupting devices. A review of the single line diagram does show multiple sources to the AC power panels including a backup generator. The one-line diagram does not show the source of the battery charging circuit. The one-line diagram does not show that a fail-safe design is being provided. These features shall be clearly demonstrated on the future Stage B technical submittals to be provided to the Connecting Transmission Owner. Battery system maintenance records shall be provided to the Connecting Transmission Owner for their review. Where no such recent maintenance records exists, the battery system shall be tested and certified by a qualified third party contractor. Battery chargers shall also be reviewed and confirmed for adequacy and suitability to the existing battery supply system.
Sample 1Sample 2Sample 3See All (6)
AutoNDA by SimpleDocs
Battery System. The exiting battery system is adequate to accommodate interconnection of the Small Generating Facility. However, to make space in the control enclosure for the protection modifications, the battery system shall be relocated to an outdoor battery cabinet with AC and DC panels. The new battery cabinet shall be approximately 84” x 114”.
Sample 1
Battery System. The manufacturer shall supply a minimum of six (6) heavy duty Group 31 12-volt maintenance-free batteries at a 1000 CCA rating. NO EXCEPTIONS. • Each battery shall be installed and positioned so as to allow easy replacement of any single battery. • Each battery shall be equipped with carrying handles to facilitate ease of removal and replacement. • There shall be two (2) steel frame mounted battery boxes, one (1) on the left frame rail and one (1) on the right frame rail. • Each battery box shall be secured to the frame rail with Grade 8 hardware. • Each battery box shall hold (2) batteries or more. • Preferred batteries shall have a minimum combined rating of 4,000 (4 x 1000) cold cranking amps (CCA) @ 0 degrees Fahrenheit and 820 (4 x 205) minutes of reserve capacity for extended operation. • The batteries shall have 3/8-16 threaded stud terminals to ensure tight cable connections. • The battery stud terminals shall each be treated with concentrated industrial soft-seal after cable installation to promote corrosion prevention. • The positive and negative battery stud terminals and the respective cables shall be clearly marked to ensure quick and mistake-proof identification. • Batteries shall be placed on non-corrosive rubber matting and secured with hold-down brackets to prevent movement, vibration, and road shock. The hold-down bracket J-hooks shall be cut to fit and shall have all sharp edges removed. • The batteries shall be placed in plastic trays to provide preliminary containment should there be leakage of hazardous battery fluids. • There shall be two (2) plastic trays, each containing (2) batteries. Each battery tray shall be equipped with a rubber vent hose to facilitate drainage. The rubber vent hose shall be routed to drain beneath the battery box. • The batteries shall be positioned in well-ventilated areas.
Sample 1
Battery System a. Measure and record the connection resistance of 100% of the inter cell/battery connections
Sample 1
Battery System. There will be a single starting system with an ignition switch and starter button provided and located on the cab instrument panel.
Sample 1
Battery System. The battery system must be supplied with the chassis.
Sample 1

Related to Battery System

  • Secondary Systems The Developer and Connecting Transmission Owner shall each cooperate with the other in the inspection, maintenance, and testing of control or power circuits that operate below 600 volts, AC or DC, including, but not limited to, any hardware, control or protective devices, cables, conductors, electric raceways, secondary equipment panels, transducers, batteries, chargers, and voltage and current transformers that directly affect the operation of Developer or Connecting Transmission Owner’s facilities and equipment which may reasonably be expected to impact the other Party. The Developer and Connecting Transmission Owner shall each provide advance notice to the other Party, and to NYISO, before undertaking any work on such circuits, especially on electrical circuits involving circuit breaker trip and close contacts, current transformers, or potential transformers.

  • Electrical appliance safety The Hirer shall ensure that any electrical appliances brought by them to the premises and used there shall be safe, in good working order, and used in a safe manner in accordance with the Electricity at Work Regulations 1989. Where a residual circuit breaker is provided the hirer must make use of it in the interests of public safety.

  • Irrigation Systems The Project Area either has no irrigation system or a low-volume drip irrigation system. If a watering system is used, it is a drip irrigation system equipped with a filter, pressure regulator and emitters rated at twenty (20) gallons per hour (gph) or less. The system is maintained free of leaks and malfunctions. No spray irrigation is applied to the Project Area, including spray from irrigation systems adjacent to the Project Area.

  • Drainage Systems (1) Clear culvert inlets, outlets, and sediment catching basins.

  • Infrastructure Vulnerability Scanning Supplier will scan its internal environments (e.g., servers, network devices, etc.) related to Deliverables monthly and external environments related to Deliverables weekly. Supplier will have a defined process to address any findings but will ensure that any high-risk vulnerabilities are addressed within 30 days.

  • Quality control system (i) The Contractor shall establish a quality control mechanism to ensure compliance with the provisions of this Agreement (the “Quality Assurance Plan” or “QAP”).

  • Quality Management System Supplier hereby undertakes, warrants and confirms, and will ensue same for its subcontractors, to remain certified in accordance with ISO 9001 standard or equivalent. At any time during the term of this Agreement, the Supplier shall, if so instructed by ISR, provide evidence of such certifications. In any event, Supplier must notify ISR, in writing, in the event said certification is suspended and/or canceled and/or not continued.

  • Orthotic Appliances Coverage for Orthotic Appliances is limited to custom-made leg, arm, back and neck braces, when related to a surgical procedure or when used in an attempt to avoid surgery, and is necessary to carry out normal activities of daily living excluding sports activities. Coverage includes the initial purchase, fitting or adjustment. Replacements are covered only when Medically Necessary due to a change in bodily configuration. All other Orthotic Appliances are not covered. The determination of whether a covered item will be paid under the DME, orthotics or prosthetics benefits will be based upon its classification as defined by the Centers for Medicare and Medicaid Services.

  • Fire Fighting Costs of operating and maintaining the fire-fighting equipments and personnel, if any.

  • Unbundled Sub-Loop Concentration System (USLC 2.9.1 Where facilities permit and where necessary to comply with an effective Commission order, BellSouth will provide <<customer_name>> with the ability to concentrate its sub-loops onto multiple DS1s back to the BellSouth Central Office. The DS1s will then be terminated into <<customer_name>>’s collocation space. TR-008 and TR303 interface standards are available.

Time is Money Join Law Insider Premium to draft better contracts faster.