Common use of Approval Clause in Contracts

Approval. 5.1. Type approval shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type approval shall only be granted if: (a) The if the vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 04 corresponding to the 00 04 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;5 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type The procedures of Annex 3 shall be followed. 4.2. If the IWVTA type submitted for approval pursuant to this Regulation meets the relevant provisions of this Regulation, approval of that type shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. belowtaking into account paragraph 12.2. 5.24.3. An A type approval number shall be assigned to each IWVTA type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeapproved in accordance with Annex 8. 5.34.4. Notice of approval or of extension or of extension, refusal or withdrawal of approval or of production definitively discontinued of a vehicle an IWVTA type pursuant to this Regulation shall be communicated by means of a secure internet database in accordance with Schedule 5 of the 1958 Agreement to the Contracting Parties applying this Regulation, using the communication form conforming to the model in Annex 12. 4.5. A type approval marking shall be affixed, as means to identify the IWVTA type, conspicuously and in a readily accessible place specified in the information document in Annex 5, to every vehicle conforming to an IWVTA type, approved under this Regulation. Such a type approval marking shall be in accordance with Annex 2. 4.6. The approval xxxx prescribed in paragraph 4.5. above may not be replaced by a Unique Identifier (UI) as referred to in Schedule 5 of the 1958 Agreement. 4.7. For vehicle systems as defined in paragraph 2.11. above the approvals of which are referenced in an IWVTA, no type approval markings need to be affixed. Approval markings for components as defined in paragraph 2.10. above need to be affixed as prescribed by the UN Regulations listed in Annex 4. 4.8. The type approval marking shall be clearly legible and be indelible. 4.9. If a vehicle data plate is fitted by the manufacturer, the type approval marking shall be placed close to or on it. 4.10. For U-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section I. For L-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section II. 4.11. All variants and versions within one IWVTA type shall be approved within one IWVTA. 4.12. Approvals for all IWVTA types within one IWVTA class shall be handled by the same approval authority. 4.13. A new IWVTA class is generated upon the granting of the first approval for an IWVTA type contained in this IWVTA class. Subsequent approvals for other 2 Until the date specified by WP.29 after the secure internet database in accordance with Schedule 5 of the 1958 Agreement (Revision 3) is operational and includes this functionality, notice of approval or of extension, refusal or withdrawal of approval of an IWVTA type pursuant to this Regulation shall be communicated as required by Article 5.2 of Revision 3 of the 1958 Agreement, as paper copies or in electronic format, to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 of this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297) mm or folded to that format and on an appropriate scale. IWVTA types may refer to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on existing IWVTA class provided the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed conditions in paragraph 5.4.11.1. of Annex 7 are met. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type The procedures of Annex 3 shall be followed. 4.2. If the IWVTA type submitted for approval pursuant to this Regulation meets the relevant provisions of this Regulation, approval of that type shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. belowtaking into account paragraph 12.2. 5.24.3. An A type approval number shall be assigned to each IWVTA type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeapproved in accordance with Annex 8. 5.34.4. Notice of approval or of extension or of extension, refusal or withdrawal of approval or of production definitively discontinued of a vehicle an IWVTA type pursuant to this Regulation shall be communicated by means of a secure internet database in accordance with Schedule 5 of the 1958 Agreement to the Contracting Parties to the Agreement applying this Regulation, by means of a using the communication form conforming to the model in Annex 1 to this Regulation12. 5.44.5. There A type approval marking shall be affixed, as means to identify the IWVTA type, conspicuously and in a readily accessible place specified on in the approval forminformation document in Annex 5, to every vehicle conforming to a vehicle type an IWVTA type, approved under this Regulation an international Regulation. Such a type approval mark consisting of:marking shall be in accordance with Annex 2. 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.24.6. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle xxxx prescribed in paragraph 5.4.14.5. above may not be replaced by a Unique Identifier (UI) as referred to in Schedule 5 of the 1958 Agreement. 5.54.7. If the For vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed systems as defined in paragraph 5.4.12.11. above the approvals of which are referenced in an IWVTA, no type approval markings need not to be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed affixed. Approval markings for components as defined in paragraph 5.4.12.10. above need to be affixed as prescribed by the UN Regulations listed in Annex 4. 5.64.8. The type approval mark marking shall be clearly legible and be indelible. 5.74.9. The If a vehicle data plate is fitted by the manufacturer, the type approval mark marking shall be placed close to or on it. 4.10. For U-IWVTA the vehicle data plate affixed approval marking shall be in accordance with the template of Annex 2, Section I. For L-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section II. 4.11. All variants and versions within one IWVTA type shall be approved within one IWVTA. 4.12. Approvals for all IWVTA types within one IWVTA class shall be handled by the manufacturersame approval authority. 5.84.13. Annex 2 A new IWVTA class is generated upon the granting of the first approval for an IWVTA type contained in this IWVTA class. Subsequent approvals for other IWVTA types may refer to this Regulation gives examples existing IWVTA class provided the conditions in paragraph 1.1. of arrangements of the approval markAnnex 7 are met.

Approval. 5.1. Type approval shall only be granted if: (a) The if the vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or of withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm) and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 3, consisting ofof either: 5.4.14.4.1. A circle surrounding the letter "E" followed by the by: (a) The distinguishing number of the country which has granted approval;approval;2 and 5.4.2. (b) The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1this paragraph; or 4.4.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.64.5. The approval mark shall be clearly legible and be indelible. 5.74.6. The approval mark authority shall be placed close to or verify the existence of satisfactory arrangements for ensuring effective checks on the vehicle data plate affixed by the manufacturerconformity of production before type-approval is granted. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 2 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the power of the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of the engine type or family shall be granted. 5.24.2. An approval number shall be assigned to each engine type or family approved. Its first two digits (at present 00 corresponding to 02 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeengine type or family. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval of an engine type or of production definitively discontinued of a vehicle type an engine family pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place as specified on the approval form, to every vehicle engine conforming to a vehicle an engine type or an engine family approved under this Regulation an international approval mark a statutory marking consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. Where the statutory marking of the engine is not visible without removing parts, the vehicle manufacturer shall affix to the category T vehicle or the non-road mobile machinery, in a visible manner, a duplicate of the marking provided by the manufacturer. 5.54.5. If the vehicle engine conforms to a vehicle an approved type approved, or family under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark statutory marking shall be placed close to or on the vehicle data plate affixed by the manufacturermanufacturer to the approved type. 5.84.7. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.8. Every engine conforming to an engine type or an engine family approved under this Regulation must bear, in addition to the approval mark.xxxx: (a) The trademark or trade name of the manufacturer of the engine and the address at which it can be contacted; (b) The manufacturer's engine type or engine family designation in case the engine type belongs to a family; (c) The unique engine identification number;

Approval. 5.1. Type approval shall only be granted if: (a) The if the vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark xxxx shall be clearly legible and be indelible. 5.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval markxxxx.

Approval. 5.1. Type If the component samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 66.1. and 7to 6.11. belowof this Regulation, approval of the type of component shall be granted. 5.2. An approval number shall be assigned to each type of component or multifunctional component approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number alphanumeric code to another vehicle typetype of component. 5.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle CNG component type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2B to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 4.2. above, to every vehicle all components conforming to a vehicle type approved under this Regulation Regulation, in addition to the mark prescribed in paragraphs 4.1. and 4.3., an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval 2/. 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.15. 4.1. This approval number consists of the component type-approval number which appears on the certificate completed for this type (see paragraph 5.2. and Annex 2B) preceded by two figures indicating the sequence of the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.85.6. Annex 2 2A to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7Paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 1 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval 1 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.3. numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets all the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 Regulation as amended by the 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle markings prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of for all the Regulations regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 to 9 below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments, its original version) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible.. 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev. 6 - https://unece.org/transpxxx/xxxxxxxxx/xxxxxxxxx/vehicle-regulations- wp29/resolutions 5.70.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type If the retrofit system sample submitted for approval shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. belowparagraph 6 of this Regulation, the type approval of the retrofit system shall be granted. 5.2. An approval number shall be assigned to each type of the retrofit system approved. Its first two digits (at present 00 corresponding according to the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same type approval number to another vehicle typetype of retrofit system. 5.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle type retrofit system type/part pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 annexes 1A and 1B to this Regulation. 5.4. There An international approval xxxx shall be affixed, conspicuously affixed in the plate as indicated in annexes 2A and in a readily accessible place specified on the approval form2B, to every vehicle all retrofit systems, conforming to a vehicle type approved under this Regulation an international Regulation, in addition to the xxxx prescribed in this paragraph 4.1. This approval mark consisting xxxx shall consist of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;the approval 3/. 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed defined in paragraph 5.4.15.4. 1. The approval number consists of the retrofit system type approval number, which appears in the communication form for this type (see paragraph 5.2. and annexes 1A and 1B) preceded by two figures indicating the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark xxxx shall be clearly legible readable and be indelible. 5.75.6. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 Annexes 2A and 2B to this Regulation gives give examples of arrangements the arrangement of the aforesaid plate with approval markxxxx.

Approval. 5.14.1. Type Granting of type approval. 4.1.1. Approval of a type of compressed hydrogen storage system. If the hydrogen storage system submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. Part I below, approval of that type of hydrogen storage system shall be granted. 5.24.1.2. Approval of a type of specific component for the compressed hydrogen storage system. If the specific component submitted for approval pursuant to this Regulation meets the requirements of Part II below, approval of that type of specific component shall be granted. 4.1.3. Approval of a vehicle type. If the vehicle submitted for approval pursuant to this Regulation meets the requirements of Part III below, approval of that vehicle type shall be granted. 4.2. An approval number shall be assigned to each type approved. Its : its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its initial form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle or component type. 5.34.3. Notice of approval or of extension or of extension, refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 1, Part 2 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle vehicle, hydrogen storage system or specific component conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the models described in Annex 2, consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need needs not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.6.1. The In the case of a vehicle, the approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.84.6.2. Annex 2 to this Regulation gives examples In the case of arrangements of a hydrogen storage system, the approval markmark shall be placed on the container. 4.6.3. In the case of a specific component, the approval mark shall be placed on the specific component.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue approved in accordance with Schedule 4 of the approval. The same Contracting Party shall not assign the same number to another vehicle typeAgreement (E/ECE/TRANS/505/Rev.3). 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to by the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. Notice of approval or of extension or of refusal of approval of a vehicle type pursuant to this Regulation shall be communicated by the Parties to the Agreement applying this Regulation by means of a form conforming to the model in Annex 1 to this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297 mm) or folded to that format and on an appropriate scale. 4.5. There shall be affixedaffixed to every vehicle conforming to a vehicle type approved under this Regulation, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.5.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.5.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.5.1. above. 5.54.6. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5.1. above need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5.1. above. 5.64.7. The approval mark shall be clearly legible and shall be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of the arrangements of the approval markmarks. 4.9. Annex 2 to this Regulation gives examples of approval marks.

Approval. 5.14.1. Type The procedures of Annex 3 shall be followed. 4.2. If the IWVTA type submitted for approval pursuant to this Regulation meets the relevant provisions of this Regulation, approval of that type shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. belowtaking into account paragraph 12.2. 5.24.3. An A type approval number shall be assigned to each IWVTA type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeapproved in accordance with Annex 8. 5.34.4. Notice of approval or of extension or of extension, refusal or withdrawal of approval or of production definitively discontinued of a vehicle an IWVTA type pursuant to this Regulation shall be communicated by means of a secure internet database in accordance with Schedule 5 of the 1958 Agreement to the Contracting Parties applying this Regulation, using the communication form conforming to the model in Annex 12. 4.5. A type approval marking shall be affixed, as means to identify the IWVTA type, conspicuously and in a readily accessible place specified in the information document in Annex 5, to every vehicle conforming to an IWVTA type, approved under this Regulation. Such a type approval marking shall be in accordance with Annex 2. 4.6. The approval mark prescribed in paragraph 4.5. above may not be replaced by a Unique Identifier (UI) as referred to in Schedule 5 of the 1958 Agreement. 4.7. For vehicle systems as defined in paragraph 2.11. above the approvals of which are referenced in an IWVTA, no type approval markings need to be affixed. Approval markings for components as defined in paragraph 2.10. above need to be affixed as prescribed by the UN Regulations listed in Annex 4. 4.8. The type approval marking shall be clearly legible and be indelible. 4.9. If a vehicle data plate is fitted by the manufacturer, the type approval marking shall be placed close to or on it. 4.10. For U-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section I. For L-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section II. 4.11. All variants and versions within one IWVTA type shall be approved within one IWVTA. 4.12. Approvals for all IWVTA types within one IWVTA class shall be handled by the same approval authority. 4.13. A new IWVTA class is generated upon the granting of the first approval for an IWVTA type contained in this IWVTA class. Subsequent approvals for other 2 Until the date specified by WP.29 after the secure internet database in accordance with Schedule 5 of the 1958 Agreement (Revision 3) is operational and includes this functionality, notice of approval or of extension, refusal or withdrawal of approval of an IWVTA type pursuant to this Regulation shall be communicated as required by Article 5.2 of Revision 3 of the 1958 Agreement, as paper copies or in electronic format, to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 of this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297) mm or folded to that format and on an appropriate scale. IWVTA types may refer to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on existing IWVTA class provided the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed conditions in paragraph 5.4.11.1. of Annex 7 are met. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that vehicle type shall be granted. 5.24.1.1. The Technical Service appointed in accordance with paragraph 12. below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue approved in accordance with Schedule 4 of the approval. The same Contracting Party shall not assign the same number to another vehicle typeAgreement (E/ECE/TRANS/505/Rev.3). 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to by the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;1 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of the arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its current form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of field of vision, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2 to this Regulation, consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval4; 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that vehicle type shall be granted. 5.24.1.1. The Technical Service appointed in accordance with paragraph 12. below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same approval number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to by the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297 mm) or folded to that format and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. The conformity of the requirements in paragraph 5. shall be verified with the test procedure as defined in paragraph 6., however its operation shall not be limited to these specific test conditions. 4.3. An approval number shall be assigned to each vehicle type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxfor this Regulation in its initial form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the this Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of MOIS, or to another vehicle type. 5.34.4. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx conforming to the model described in Annex 2, consisting ofof either: 5.4.14.5.1. A circle surrounding the letter "E" followed by by: (a) the distinguishing number of the country which has granted approval;approval;2 and 5.4.2. The (b) the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1this paragraph; or 4.5.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 5.54.6. If the vehicle conforms to a vehicle type approved, approved under one or more other UN Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5. above need not be repeated; in . In such a case case, the regulation UN Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5. above. 5.64.7. The approval mark xxxx shall be clearly legible and be indelible. 5.74.8. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets all the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxregulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle markings prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of for all the Regulations regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The pursuant to this Regulation meets the relevant requirements of this Regulation, approval of that vehicle type meets the requirements of paragraphs 6. and 7. belowshall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 08, corresponding to the 00 08 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype as defined in paragraph 2.2. above. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this the Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.4.3. The letter "e", to the right of the number of this Regulation in the case of type approval according to the dynamic test of Annex 7. 4.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed Annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation and approval additional numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 2 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14. 4.1. 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6, Annex 3 - above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type 23.1 If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 24 below, approval of that vehicle type shall be granted. 5.2. 23.2 An approval number shall be assigned to each vehicle type approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xx20 April 1986) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle type. 5.3. 23.3 Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 annex 2 to this Regulation. 5.4. 23.4 There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. 23.4.1 A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;, l/ 5.4.2. 23.4.2 The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. 23.4.3 The following additional symbols a rectangle surrounding a figure expressing in m -1 the corrected absorption coefficient obtained, at the time of approval, during the test under free acceleration, and determined at the time of approval by the procedure described in annex 5, paragraph 3.2, to this Regulation. 23.5 If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. 23.4.1 need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the l/ See footnote on page 4. UN ECE Regulation 24/03 15 Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.123.4.1. 5.6. 23.6 The approval mark and the additional symbol shall be clearly legible and be indelible. 5.7. 23.7 The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. 23.8 Annex 2 3 to this Regulation gives examples of the arrangements of the approval markmark and of the additional symbol.

Approval. 5.17.1. Type If the CNG component samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 68.1. and 7to 8.11. belowof this Regulation, approval of the type of component shall be granted. If the LNG components samples submitted for approval meet the requirements of paragraphs 8.12. to 8.21. of this Regulation, approval of the type of component shall be granted. 5.27.2. An approval number shall be assigned to each type of component or multifunctional component approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number alphanumeric code to another vehicle typetype of component. 5.37.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle CNG or LNG component type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2B to this Regulation. 5.47.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 6.2. above, to every vehicle all components conforming to a vehicle type approved under this Regulation Regulation, in addition to the xxxx prescribed in paragraphs 6.1. and 6.3. (CNG) and 6.4. (LNG), an international approval mark xxxx consisting of: 5.4.17.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval.11 5.4.27.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.17.4.1. above. This approval number consists of the component type approval number which appears on the certificate completed for this type (see paragraph 7.2. above and Annex 2B) preceded by two figures indicating the sequence of the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.67.5. The approval mark xxxx shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.87.6. Annex 2 2A to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe Regulation in respect of all the devices specified in the list, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 04, corresponding to the 00 04 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same this number to another vehicle typetype or to the same vehicle type submitted with equipment not specified in the list referred to in paragraph 3.2.2. above, subject to the provisions of paragraph 7. of this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type type/part pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval5; 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not to be repeated; , in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of approval marks. 5 The distinguish numbers of the approval markContracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document TRANS/WP.29/78/Rev.2/Amend.1.

Approval. 5.113.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 14. below, approval for this vehicle type shall be granted. 5.213.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxUN Regulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the UN Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same this number to another vehicle type. 5.313.3. Notice of Communication on approval or of extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 1B to this the UN Regulation. 5.413.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to On every vehicle conforming which conforms to a vehicle type approved under this Regulation there shall be affixed conspicuously, in an easily accessible place indicated on the approval form, an international approval mark consisting ofcomprising: 5.4.113.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval6; 5.4.213.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number placed to the right of the circle prescribed in paragraph 5.4.113.4.1. 5.513.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.113.4.2. need not be repeated; in such a case the regulation UN Regulation and approval numbers and the additional symbols of all the UN Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.113.4. 5.613.6. The approval mark shall must be clearly legible and be indelible. 5.713.7. The approval mark shall be placed close to or on near the plate bearing the characteristics of the vehicle data plate and may also be affixed by the manufacturerto this plate. 5.813.8. Annex 2 2, Section II, to this Regulation gives examples an example of arrangements the arrangement of the approval mark. 13.9. The Type Approval Authority shall verify the existence of satisfactory arrangements for ensuring effective control of the conformity of production before type approval is granted.

Approval. 5.14.1. Type If the power of the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of the engine type or family shall be granted. 5.24.2. An approval number shall be assigned to each engine type or family approved. Its first two digits (at present 00 corresponding to 02 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeengine type or family. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval of an engine type or of production definitively discontinued of a vehicle type an engine family pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place as specified on the approval form, to every vehicle engine conforming to a vehicle an engine type or an engine family approved under this Regulation an international approval mark a statutory marking consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. Where the statutory marking of the engine is not visible without removing parts, the vehicle manufacturer shall affix to the category T vehicle or the non-road mobile machinery, in a visible manner, a duplicate of the marking provided by the manufacturer. 5.54.5. If the vehicle engine conforms to a vehicle an approved type approved, or family under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark statutory marking shall be placed close to or on the vehicle data plate affixed by the manufacturermanufacturer to the approved type. 5.84.7. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.8. Every engine conforming to an engine type or an engine family approved under this Regulation must bear, in addition to the approval mark.: (a) The trademark or trade name of the manufacturer of the engine and the address at which it can be contacted; (b) The manufacturer's engine type or engine family designation in case the engine type belongs to a family; (c) The unique engine identification number;

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 5. and 6. and 7. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its , its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype with regard to Brake Assist System. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and of a summary of the information contained in the documents referred to in paragraphs 3.2.1. to 3.2.4. above, the drawings supplied by the applicant for approval being in a format not exceeding A4 (210 x 297 mm), or folded to that format, and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval,3 and of 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above, need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: pursuant to this Regulation meets the relevant requirements (a) The seats fitted with head restraints or capable of being fitted with head restraints), approval of the vehicle type meets the requirements of paragraphs 6. and 7. belowshall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 10, corresponding to the 00 10 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number either to the same vehicle type equipped with other types of seats or head restraints or with seats anchored differently on the vehicle (this applies both to seats with and to those without head restraints) or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.4.3. However, if the vehicle is equipped with one or more seats fitted or capable of being fitted with head restraints, approved as meeting the requirements under paragraphs 5.2. and 5.3. below, the number of this Regulation shall be followed by the letters "RA". The form conforming to the model in Annex 1 to this Regulation shall indicate which seat(s) of the vehicle is (are) fitted or capable of being fitted with head restraints. The marking shall also indicate that any remaining seats in the vehicle, not fitted or capable of being fitted with head restraints, are approved and meet the requirements of paragraph 5.2. below of this Regulation. 4.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Examples of arrangements of approval marks are given in Annex 2 to this Regulation gives examples of arrangements Regulation. 2 The distinguishing numbers of the approval mark.Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6, Annex 3 - https://unece.xxx/xxxxxxxxx/xxxxxxxxx/transport/vehicle-regulations-wp29/resolutions

Approval. 5.1. Type The approval of a headlamp cleaner shall extend only be granted if:to the operating principle employed for the cleaning of either the types or the shapes and functions of headlamps indicated in the application for approval; (a) The 5.2. If the type of headlamp cleaner or vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. 6 and 7. 7 below, approval of that type of headlamp cleaner or vehicle shall be granted. 5.25.3. An approval number shall be assigned to each type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xx9 February 1988) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another type of vehicle typeor headlamp cleaner. 5.35.4. Notice of approval or approval, of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex annex 1 to this RegulationRegulation and of drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297 mm), or folded to that format, and on an appropriate scale. Notice of approval, of extension or of refusal of approval of a type of headlamp cleaner shall be communicated to the Parties to the Agreement which apply this Regulation by means of a form conforming to the model in annex 2 to this Regulation and of drawings supplied by the applicant for approval, in a format not exceeding A4/(210 x 297 mm), or folded to that format, and on an appropriate scale. 5.45.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or headlamp cleaner conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.15.5.1. A circle surrounding the letter "“E" ” followed by the distinguishing number of the country which has granted approval;granting approval;3 5.4.25.5.2. The For a vehicle type, the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.15.5.1.; 5.5.3. For a vehicle type, the following additional symbol: a rectangle surrounding a figure expressing the capacity class of the fluid container; the class can be either 50 or 25 as stipulated in paragraph 6.5.2.1.; 5.5.4. For a type of headlamp cleaner, an approval number. 5.55.6. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. 5.5.1., need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.15.5.1. 5.65.7. The approval mark shall be clearly legible and be indelible. 5.75.8. The For a vehicle type, the approval mark shall be placed either near the headlamps or close to or on the vehicle data plate affixed by the manufacturermanufacturer showing the characteristics of the vehicle. 5.85.9. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 3 1 for Germany, 2 for France, 3 for Italy, 4 for the approval markNetherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Serbia, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 14 for Switzerland, 15 (vacant), 16 for Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Ireland, 25 for Croatia, 26 for Slovenia, 27 for Slovakia, 28 for Belarus, 29 for Estonia, 30 (vacant), 31 for Bosnia and Herzegovina, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Union (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine, 47 for South Africa, 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant), 56 for Montenegro, 57 (vacant) and 58 for Tunisia. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 5. and 6. and 7. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its , the first two digits (at present 00 corresponding to of which shall be the 00 series highest number of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to incorporated in the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 annex 2 to this RegulationRegulation and of drawings and diagrams supplied by the applicant for approval, in a format not exceeding A 4 (210 x 297 mm) or folded to that format and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A a circle surrounding the letter "“E" ” followed by the distinguishing number of the country which has granted approval;; 1/ 5.4.24.4.2. The the number of this Regulation, followed by the letter "“R"”, a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle vertical data plate affixed by the manufacturer. 5.84.8. Annex 2 3 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.117.1. Type If the vehicle submitted for approval shall only be granted if: pursuant to this Regulation is equipped with all the necessary specific components for the use of compressed natural gas (aCNG) The vehicle type and/or liquefied natural gas (LNG) in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 18. below, approval of that vehicle type shall be granted. 5.217.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.317.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a CNG and/or LNG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.417.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 17.2. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.117.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 12 12 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.3, Annex 3 - xxx.xxxxx.xxx/xxxxx/xxxx/xx00/xx00xxx/xx00xxx/xx00xxxxxxxxxxx.xxxx. 5.4.217.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.117.4.1. above. 5.517.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which that has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.117.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.117.4.1. above. 5.617.6. The approval mark xxxx shall be clearly legible and be indelible. 5.717.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.817.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.1. Type If the NORESS or component thereof submitted for approval shall only be granted if: (a) The vehicle type under this UN Regulation meets the requirements of paragraphs paragraph 6. and 7. below, approval for that type shall be granted. 5.2. An approval number shall be assigned to each NORESS type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxto the UN Regulation) shall indicate the series of amendments incorporating the most recent major technical amendments made to the UN Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of NORESS or component designed for, the same type(s) of vehicle. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to NORESS or component thereof under this UN Regulation shall be communicated to the Parties to the Agreement applying which apply this UN Regulation, by means of a form conforming to the model in Annex 1 to this UN Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, affixed to every vehicle NORESS and component thereof conforming to a vehicle type approved under this UN Regulation an international approval mark consisting of: 5.4.1. (a) A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;4 5.4.2. (b) The number of this UN Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1(a) above; (c) The approval number shall be indicated in the approval form, together with the method used for the approval tests. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly easily legible when the NORESS is fitted to the vehicle, and shall be indelible. 5.75.6. The A component may be marked with more than one approval mark shall number if it has been approved as a part of more than one NORESS; in this case the circle need not to be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8repeated. Annex 2 to this UN Regulation gives examples of arrangements an example of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 below, approval of that vehicle type shall be granted. 5.24.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.3. An approval number shall be assigned to each vehicle type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same approval number to another vehicle type. 5.34.4. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 of this Regulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297) mm or folded to this Regulationthat format and on an appropriate scale. 5.44.5. There shall be affixedaffixed to every vehicle conforming to a vehicle type approved under this Regulation, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.5.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 4 5.4.24.5.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.5.1. 5.54.6. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been 4 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev. 3, Annex 3 - xxx.xxxxx.xxx/xxxxx/xxxx/xx00/xx00xxx/xx00xxx/xx00xxxxxxxxxxx.xxxx granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5.1. 5.64.7. The approval mark xxxx shall be clearly legible and shall be indelible. 5.74.8. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.9. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.1. Type If the component samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 66.1. and 7to 6.11. belowof this Regulation, approval of the type of component shall be granted. 5.2. An approval number shall be assigned to each type of component or multifunctional component approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number alphanumeric code to another vehicle typetype of component. 5.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle CNG component type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2B to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 4.2. above, to every vehicle all components conforming to a vehicle type approved under this Regulation Regulation, in addition to the xxxx prescribed in paragraphs 4.1. and 4.3., an international approval mark xxxx consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval 2/. 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.15. 4.1. This approval number consists of the component type-approval number which appears on the certificate completed for this type (see paragraph 5.2. and Annex 2B) preceded by two figures indicating the sequence of the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark xxxx shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.85.6. Annex 2 2A to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 2 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type approval shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval1; 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark xxxx shall be clearly legible and be indelible. 5.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval markxxxx.

Approval. 5.14.1. Type When the maximum speed of a vehicle submitted for approval shall only be granted if: (a) The vehicle type meets under this Regulation has been measured in accordance with the requirements of paragraphs 6. paragraphs/5 and 7. 6 below, this vehicle type shall be approved. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 2/ 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, this Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14. 4.1. need not be repeated; in such a this case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and shall be indelible. 5.74.7. The approval mark xxxx shall be placed on or close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 5. and 6. and 7. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its , its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx11) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of braking system, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this RegulationRegulation and of a summary of the information contained in the documents referred to in paragraphs 3.2.1. to 3.2.4. above, the drawings supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to that format, and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval,3 and 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. However, if a vehicle of categories M2 or M3 has been approved pursuant to the provisions of Annex 4, paragraph 1.8. to this Regulation, the number of the Regulation shall be followed by the letter M. 4.6. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.7. The approval mark shall be clearly legible and be indelible. 5.74.8. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.84.9. Annex 2 3 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 to 9 below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments, its original version) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type approval Each sample submitted in conformity with paragraphs 3.2.4. and 3.2.5. above shall only be granted if: (a) The vehicle type meets meet the requirements of specifications set forth in paragraphs 6. and to 7. belowof this Regulation in every respect before approval can be granted. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the this Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of Enhanced Child Restraint System covered by this Regulation. A type of Enhanced Child Restraint System approved according to this Regulation shall not bear another approval xxxx according to UN Regulation No. 44 (Child Restraint Systems). 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type an Enhanced Child Restraint System pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. If part of the Enhanced Child Restraint System could be used as an infant carrier module and installed as defined in Annex 22, approvals according to this Regulation can only be granted if the infant carrier module complies with the requirements of this annex. 5.4. There In addition to the marks prescribed in paragraph 4. above, the following particulars shall be affixed, conspicuously and affixed in a readily accessible place specified on the approval form, suitable space to every vehicle Enhanced Child Restraint System conforming to a vehicle type approved under this Regulation an Regulation: 5.4.1. An international approval mark xxxx consisting of: 5.4.15.4.1.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval;1 5.4.1.2. An approval number, the words "UN Regulation No." followed by the number of this Regulation, a slash and the series of amendment ("UN Regulation No. 129/00"); 5.4.2. The number following additional symbols: 5.4.2.1. The words "i-Size universal ISOFIX", or "specific vehicle ISOFIX" depending on the category of Enhanced Child Restraint System; 5.4.2.2. The size range for which the Enhanced Child Restraint System has been designed. In case the ECRS is equipped with a module, the size range is not on the approval xxxx but on the module xxxx. ECRS which can be converted into another configuration for taller children shall accommodate an uninterrupted range of child statures. 5.4.2.3. The symbol "S" in the case of a "Special Needs Restraint". 5.4.3. An international module xxxx as defined in Annex 2 to this Regulation, Regulation consisting of: 5.4.3.1. The words "R129" followed by the letter "R", a dash and the same approval number to as the right part of the circle prescribed in paragraph 5.4.1.ECRS which includes the ISOFIX connectors; 5.4.3.2. The words Module “name of the Module", depending on the name of the module of Enhanced Child Restraint System; 5.4.3.3. The size range including maximum weight for which the Module of the Enhanced Child Restraint System has been designed; 5.5. If the vehicle conforms Annex 2 to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right gives an example of the symbol prescribed in paragraph 5.4.1arrangement of the approval xxxx. 5.6. The approval mark particulars referred to in paragraph 5.4. above shall be clearly legible and be indelible, and may be affixed either by means of a label or by direct marking. The label or marking shall be resistant to wear. 5.7. The labels referred to in paragraph 5.6. above may be issued either by the Type Approval Authority which has granted the approval mark shall be placed close or, subject to or on the vehicle data plate affixed that Type Approval Authority's authorization, by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements 1 The distinguishing numbers of the approval mark.Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev. 6, Annex 3 – xxx.xxxxx.xxx/xxxxx/xxxx/xx00/xx00xxx/xx00xxx/xx00xxxxxxxxxxx.xxxx

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or of withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm) and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 3, consisting ofof either: 5.4.14.4.1. A circle surrounding the letter "E" followed by the by: (a) The distinguishing number of the country which has granted approval;approval;2 and 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document 5.4.2. (b) The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1this paragraph; or 4.4.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.64.5. The approval mark shall be clearly legible and be indelible. 5.74.6. The approval mark authority shall be placed close to or verify the existence of satisfactory arrangements for ensuring effective checks on the vehicle data plate affixed by the manufacturerconformity of production before type- approval is granted. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or of withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm) and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 3, consisting ofof either: 5.4.14.4.1. A circle surrounding the letter "E" followed by the by: (a) The distinguishing number of the country which has granted approval;approval;2 and 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6 - https://unece.org/transpxxx/xxxxxxxxx/xxxxxxxxx/vehicle-regulations-wp29/resolutions 5.4.2. The (b) Xxx number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1this paragraph; or 4.4.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.64.5. The approval mark shall be clearly legible and be indelible. 5.74.6. The approval mark authority shall be placed close to or verify the existence of satisfactory arrangements for ensuring effective checks on the vehicle data plate affixed by the manufacturerconformity of production before type- approval is granted. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7Paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 1 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe Regulation in respect of all the devices specified in the list, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 Regulation in its 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype or to the same vehicle type submitted with equipment not specified in the list referred to in paragraph 3.2.2. above, subject to the provisions of paragraph 7. of this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, Regulation followed by the letter "R", a dash dash, and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements the arrangement of the approval markmarks.

Approval. 5.16.1. Type approval shall only be granted if: (a) The vehicle type meets the requirements of Each sample submitted in conformity with paragraphs 64.2.2. and 4.2.3. above shall meet the specifications set forth in paragraph 7. belowof this Regulation in every respect before approval can be granted. 5.26.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approvalamendments. The same Contracting Party shall not assign the same number to another vehicle typetype of Child Restraint System covered by this Regulation. A type of Child Restraint System approved according to this Regulation shall not bear another approval mark according to any other Regulation regarding CRS. 5.36.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type Child Restraint Systems pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.46.4. There In addition to the marks prescribed in paragraph 5. above, the following particulars shall be affixed, conspicuously and affixed in a readily accessible place specified on the approval form, suitable space to every vehicle Child Restraint System conforming to a vehicle type approved under this Regulation an Regulation: 6.4.1. An international approval mark consisting of: 5.4.16.4.1.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;1 1 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.7, Annex 3 - xxxxx://xxxxx.xxx/transport/standards/transport/vehicle- regulations-wp29/resolutions 5.4.26.4.1.2. The An approval number, the words "Regulation No." followed by the number of this Regulation, followed by the letter "R", a dash slash and the approval number to series of amendment ("Regulation No. XXX/XX"); 6.4.2. The following additional symbols: 6.4.2.1. The size range for which the right Child Restraint System has been designed; 6.4.2.2. The symbol "S" in the case of the circle prescribed in paragraph 5.4.1a "Special Needs Restraint". 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.86.5. Annex 2 to this Regulation gives examples an example of arrangements the arrangement of the approval mark. 6.6. The particulars referred to in paragraph 6.4. above shall be clearly legible and be indelible and may be affixed either by means of a label or by direct marking. The label or marking shall be resistant to wear. 6.7. The labels referred to in paragraph 6.4. above may be issued either by the Type Approval Authority which has granted the approval or, subject to that Type Approval Authority's authorization, by the manufacturer.

Approval. 5.117.1. Type If the vehicle submitted for approval shall only be granted if: pursuant to this Regulation is equipped with all the necessary specific components for the use of compressed natural gas (aCNG) The vehicle type and/or liquefied natural gas (LNG) in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 18. below, approval of that vehicle type shall be granted. 5.217.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.317.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a CNG and/or LNG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.417.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 17.2. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.117.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 0 5.4.217.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.117.4.1. above. 5.517.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which that has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.117.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.117.4.1. above. 5.617.6. The approval mark xxxx shall be clearly legible and be indelible. 5.717.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.817.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets all the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 Regulation as amended by the 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of vehicle. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle markings prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of for all the Regulations regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 02 corresponding to the 00 02 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 1, Part 2 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need needs not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that vehicle type shall be granted. 5.24.1.1. The Technical Service appointed in accordance with paragraph 12. below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same approval number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to by the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 x 297 mm) or folded to that format and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.1. Type approval Each sample submitted in conformity with paragraphs 3.2.4. and 3.2.5. above shall only be granted if: (a) The vehicle type meets meet the requirements of specifications set forth in paragraphs 6. and to 7. belowof this Regulation in every respect before approval can be granted. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the this Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of Enhanced Child Restraint System covered by this Regulation. A type of Enhanced Child Restraint System approved according to this Regulation shall not bear another approval xxxx according to UN Regulation No. 44 (Child Restraint Systems). 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type an Enhanced Child Restraint System pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. If part of the Enhanced Child Restraint System could be used as an infant carrier module and installed as defined in Annex 22, approvals according to this Regulation can only be granted if the infant carrier module complies with the requirements of this annex. 5.4. There In addition to the marks prescribed in paragraph 4. above, the following particulars shall be affixed, conspicuously and affixed in a readily accessible place specified on the approval form, suitable space to every vehicle Enhanced Child Restraint System conforming to a vehicle type approved under this Regulation an Regulation: 5.4.1. An international approval mark xxxx consisting of: 5.4.15.4.1.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval;0 5.4.1.2. An approval number, the words "UN Regulation No." followed by the number of this Regulation, a slash and the series of amendment ("UN Regulation No. 129/00"); 5.4.2. The number following additional symbols: 5.4.2.1. The words "i-Size universal ISOFIX", or "i-Size booster seat", or "specific vehicle ISOFIX" or "specific vehicle booster seat" or "Universal Belted", or "Specific vehicle Belted", depending on the category of Enhanced Child Restraint System; 5.4.2.2. The size range for which the Enhanced Child Restraint System has been designed; 5.4.2.3. In case the ECRS is equipped with a module, the size range is not on the approval xxxx but on the module xxxx. 5.4.2.4. The symbol "S" in the case of a "Special Needs Restraint". 5.4.3. An international module xxxx as defined in Annex 2 to this Regulation, Regulation consisting of: 5.4.3.1. The words "R129" followed by the letter "R", a dash and the same approval number to as the right part of the circle Enhanced Child Restraint System which includes the ISOFIX attachments or main load bearing contact points; 5.4.3.2. The words Module "name of the Module", depending on the name of the module of Enhanced Child Restraint System; 5.4.3.3. The size range including maximum weight for which the Module of the Enhanced Child Restraint System has been designed; 5.5. The approval xxxx prescribed in paragraph 5.4.1. 5.55.4. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need above may not be repeated; replaced by an Unique Identifier (UI) as referred to in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right Schedule 5 of the symbol prescribed in paragraph 5.4.11958 Agreement. 5.6. Annex 2 to this Regulation gives an example of the arrangement of the approval xxxx. 5.7. The approval mark particulars referred to in paragraph 5.4. above shall be clearly legible and be indelible, and may be affixed either by means of a label or by direct marking. The label or marking shall be resistant to wear. 5.75.8. The labels referred to in paragraph 5.6. above may be issued either by the Type Approval Authority which has granted the approval mark shall be placed close or, subject to or on the vehicle data plate affixed that Type Approval Authority's authorization, by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.116.1. Type If the samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 6paragraph 17. of this Regulation, approval of the pertinent type of AECD shall be granted. If the application for an AECD approval according to this Part of the Regulation makes reference to AECC approval(s) obtained in accordance with Part Ia, the manufacturer shall provide a documentation package which gives access to the basic design of the AECD and 7the means by which it is intended to be linked (e.g. identification number) to AECC of Part Ia. The manufacturer shall provide a documentation package which gives access to the basic design of the AECD and the means by which it is intended to be linked (e.g. identification number) to a subsequent installation of AECD approved according to Part II. belowIf the AECD application makes reference to AECC approval(s) obtained in accordance with Part Ia, the competent authority shall verify which requirements and which AECC components have already been covered by the AECC approval(s) and avoid any duplication of the related verifications. 5.216.2. An approval number shall be assigned to each type approved. Its The first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx00) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of AECD. 5.316.3. Notice of approval or of extension refusal, or of refusal extension or withdrawal of approval approval, or of production definitively discontinued of a vehicle type of AECD pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 15.2. above, to every vehicle AECD conforming to a vehicle type approved under this Regulation Regulation, in addition to the mark prescribed in paragraph 15.1., an international approval mark conforming to the model given in Annex 2, consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.616.5. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1The manufacturer shall provide a documentation package which gives access to the basic design of the AECC and the means by which it is intended to be linked (e.g. identification number) to other subsequent AECD approval(s) of Part Ib. 6.1. Type If the samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 6. and paragraph 7. belowof this Regulation, approval of the pertinent type of AECC shall be granted. Since some of the requirements of paragraph 7. are optional, the competent authority shall indicate in the communication document of Annex 1 which verifications are made for the AECC. 5.26.2. An approval number shall be assigned to each type approved. Its The first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx00) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of AECC. 5.36.3. Notice of approval or of extension refusal, or of refusal extension or withdrawal of approval approval, or of production definitively discontinued of a vehicle type of AECC pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.46.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 5.2. above, to every vehicle AECC conforming to a vehicle type approved under this Regulation Regulation, in addition to the mark prescribed in paragraph 5.1., an international approval mark conforming to the model given in Annex 1, consisting of: 5.4.16.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.26.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.16.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.66.5. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.116.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation is provided with all the necessary specific components for the use of compressed natural gases in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 17. below, approval of that vehicle type shall be granted. 5.216.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.316.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a CNG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 16.2. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval2; 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4.1. above. 5.516.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.116.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.116.4.1. above. 5.616.6. The approval mark xxxx shall be clearly legible and be indelible. 5.716.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.816.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs paragraph 5. below, approval of that vehicle type shall be granted. 4.2. The conformity of the requirements in paragraph 5. below shall be verified with the test procedure as defined in paragraph 6. and 7. below, however its operation shall not be limited to these test conditions. 5.24.3. An approval number shall be assigned to each vehicle type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxfor this Regulation in its initial form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the this Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of BSIS, or to another vehicle type. 5.34.4. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting ofof either: 5.4.14.5.1. A circle surrounding the letter "E" followed by by: (a) the distinguishing number of the country which has granted approval;approval;2 and 5.4.2. The (b) the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1.this paragraph; or 5.54.5.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6 - xxx.xxxxx.xxx/xxxxx/xxxx/xx00/xx00xxx/xx00xxx/xx00xxxxxxxxxxx.xxxx 4.6. If the vehicle conforms to a vehicle type approved, approved under one or more other UN Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5. above need not be repeated; in . In such a case case, the regulation UN Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5. above. 5.64.7. The approval mark shall be clearly legible and be indelible. 5.74.8. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.116.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation is provided with all the necessary specific components for the use of compressed natural gases in its propulsion system and meets the requirements of paragraphs 6. and 7. paragraph 17 below, approval of that vehicle type shall be granted. 5.216.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.316.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a CNG and or LNG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 16.2. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 2/; 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4. 5.516.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.116.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.116.4.1. 5.616.6. The approval mark shall be clearly legible and be indelible. 5.716.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.816.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark. Estonia, 30 (vacant), 31 for Bosnia and Herzegovina, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine, 47 for South Africa, 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant), 56 for Montenegro, 57 (vacant) and 58 for Tunisia. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement.

Approval. 5.1. Type approval shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. below. 5.24.1. An approval number shall be assigned to each approved type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue in accordance with Schedule 4 of the approval. The same Contracting Party shall not assign the same number to another vehicle typeAgreement (E/ECE/TRANS/505/Rev.3). 5.34.2. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1, Part 1 or 2 as appropriate to this Regulation. 5.44.3. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or REESS conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.3.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval3. 5.4.24.3.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.3.1. 5.54.3.3. In the case of an approval of a REESS the "R" shall be followed by the symbol "ES". 4.4. If the vehicle or REESS conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.3.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.3.1. 5.64.5. The approval mark shall be clearly legible and shall be indelible. 5.74.5.1. The In the case of a vehicle, the approval mark shall be placed on or close to or on the vehicle data plate affixed by the manufacturer. 5.84.5.2. In the case of a REESS, the approval mark shall be affixed on the major element of the REESS by the manufacturer. 4.6. Annex 2 to this Regulation gives examples of the arrangements of the approval mark.

Approval. 5.17.1. Type If the CNG component samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 68.1. and 7to 8.11. belowof this Regulation, approval of the type of component shall be granted. If the LNG components samples submitted for approval meet the requirements of paragraphs 8.12. to 8.22. of this Regulation, approval of the type of component shall be granted. 5.27.2. An approval number shall be assigned to each type of component or multifunctional component approved. Its first two digits (at present 00 02 corresponding to the 00 02 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number alphanumeric code to another vehicle typetype of component. 5.37.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle CNG or LNG component type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2B to this Regulation. 5.47.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 6.2. above, to every vehicle all components conforming to a vehicle type approved under this Regulation Regulation, in addition to the mark prescribed in paragraphs 6.1. and 6.3. (CNG) and 6.4. (LNG), an international approval mark consisting of: 5.4.17.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval.0 5.4.27.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.17.4.1. above. This approval number consists of the component type approval number which appears on the certificate completed for this type (see paragraph 7.2. above and Annex 2B) preceded by two figures indicating the sequence of the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.67.5. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.87.6. Annex 2 2A to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark.

Approval. 5.14.1. Type If the replacement catalytic converter submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 below, approval of that type of replacement catalytic converter shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at 00 for the Regulation in its present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxform) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of replacement catalytic converter. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type of replacement catalytic converter pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle the replacement catalytic converter conforming to a vehicle type of replacement catalytic converter approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 2/; 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to in the right vicinity of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle replacement catalytic converter conforms to a vehicle catalytic converter type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be indelible and clearly legible and be indeliblewhen the replacement catalytic converter is mounted under the vehicle. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.7. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.1. Type 14.1 If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation, meets the requirements of paragraphs 6. and 7. paragraph 15 below, approval for the vehicle type shall be granted. 5.2. 14.2 An approval number shall be assigned to each vehicle type approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xx20 April 1986) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle type. 5.3. 14.3 Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation Regulation, shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 annex 2 to this Regulation.. UN ECE Regulation 24/03 10 5.4. 14.4 There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. 14.4.1 A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;, 1/ 5.4.2. 14.4.2 The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.114.4.11 14.4.3 The following additional symbol a rectangle surrounding a figure expressing in m-l the absorption coefficient determined during the test under free acceleration, in annex 5 of this Regulation. 5.5. 14.5 If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. 14.4.1 need not be repeated; repeatedly in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.114.4.1. 5.6. 14.6 The approval mark and the additional symbol shall be clearly legible and be indelible. 5.7. 14.7 The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. 14.8 Annex 2 3 to this Regulation gives examples of the arrangements of the approval markmark and of the additional symbol.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The pursuant to this Regulation meets all relevant requirements given in this Regulation, approval of that vehicle type meets with regard to the requirements steering equipment shall be granted. 4.1.1. The Type Approval Authority shall verify the existence of paragraphs 6. and satisfactory arrangements for ensuring effective control of the conformity of production as given in paragraph 7. belowof this Regulation, before type approval is granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx03) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same this number to another vehicle typetype or to the same vehicle type submitted with different steering equipment from that described in the documents required by paragraph 3. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and shall be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of approval marks. 3 The distinguishing numbers of the approval mark.Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.6, Annex 3 - https://unece.xxx/xxxxxxxxx/xxxxxxxxx/transport/vehicle- regulations-wp29/resolutions

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The pursuant to this Regulation meets the relevant requirements of this Regulation, approval of that vehicle type meets the requirements of paragraphs 6. and 7. belowshall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 08, corresponding to the 00 08 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype as defined in paragraph 2.2. above. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this the Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.4.3. The letter "e", to the right of the number of this Regulation in the case of type approval according to the dynamic test of Annex 7. 4.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed Annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation and approval additional numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markxxxx.

Approval. 5.1The application for the installation of an AECD according to Part II of this Regulation shall make reference to AECD approval(s) obtained in accordance with Part Ib, the manufacturer shall provide a documentation package which gives access to the basic configuration of the AECD installation and the means by which it is intended to be linked (e.g. identification number) to the AECD of Part Ib. 25.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 26. below, approval of that vehicle type shall be granted. Before granting approval for a vehicle type with regard to the installation of an AECD approved to Part Ib of this Regulation, the competent authority shall ensure that the verifications not being part of the Part Ib approval are included in the Part II approval. If in this case, the power supply other than back-up power supply is the only power supply and if it is not covered in Part Ia according to paragraph 7.7. or in Part Ib according to paragraph 17.7.2., this shall be tested according to Annex 9 for this part. 5.225.2. An approval number shall be assigned to each type approved. Its The first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx00) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetype of vehicle. 5.325.3. Notice of approval or of extension refusal, or of refusal extension or withdrawal of approval approval, or of production definitively discontinued of a type of vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 3 to this Regulation. 5.425.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark conforming to the model given in Annex 3, consisting of: 5.4.125.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.225.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.125.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.625.5. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the type submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe relevant parts of this Regulation, approval of that type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 02 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1, Part 1 or 2 as appropriate to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or REESS or separate technical unit conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval3. 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.4.1. 5.54.4.3. In the case of an approval of a REESS or a separate technical unit of the REESS the "R" shall be followed by the symbol "ES". 4.5. If the vehicle or REESS conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1.4.4.1. 3 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.2/Amend.3 5.64.6. The approval mark xxxx shall be clearly legible and shall be indelible. 5.74.6.1. The In the case of a vehicle, the approval mark xxxx shall be placed on or close to or on the vehicle data plate affixed by the manufacturer. 5.84.6.2. In the case of a REESS or separate technical unit approved as a REESS, the approval xxxx shall be affixed on the major element of the REESS by the manufacturer. 4.7. Annex 2 to this Regulation gives examples of the arrangements of the approval markxxxx.

Approval. 5.1. Type If the equipment samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 66.1. and 7to 6.13. belowof this Regulation, approval of the type of equipment shall be granted. 5.2. An approval number shall be assigned to each type of equipment approved. Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number this alphanumeric code to another vehicle typetype of equipment. 5.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a vehicle type an LPG equipment type/part pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2B to this Regulation. If it concerns a container, Annex 2B - Appendix shall be added. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval formspace referred to in paragraph 4.2. above, to every vehicle all equipment conforming to a vehicle type approved under this Regulation Regulation, in addition to the mark prescribed in paragraphs 4.1. and 4.3. above, an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval1. 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. above. This approval number consists of the component type approval number which appears on the certificate completed for this type (see paragraph 5.2. above and Annex 2B) preceded by two figures indicating the sequence of the latest series of amendments to this Regulation. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.85.6. Annex 2 2A to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark. 5.7. In case of a Class 0 component also the working pressure shall be marked in the vicinity of the approval markmark mentioned in paragraph 5.4. above.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: pursuant to this Regulation meets the relevant requirements (a) The seats fitted with head restraints or capable of being fitted with head restraints), approval of the vehicle type meets the requirements of paragraphs 6. and 7. belowshall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 07, corresponding to the 00 07 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number either to the same vehicle type equipped with other types of seats or head restraints or with seats anchored differently on the vehicle (this applies both to seats with and to those without head restraints) or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 3/ 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.4.3. However, if the vehicle is equipped with one or more seats fitted or capable of being fitted with head restraints, approved as meeting the requirements under paragraphs 5.1. and 5.2. below, the number of this Regulation shall be followed by the letters "RA". The form conforming to the model in annex 1 to this Regulation shall indicate which seat(s) of the vehicle is (are) fitted or capable of being fitted with head restraints. The marking shall also indicate that any remaining seats in the vehicle, not fitted or capable of being fitted with head restraints, are approved and meet the requirements of paragraph 5.1. below of this Regulation. 4.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 10 for Yugoslavia, 11 for the United Kingdom, 12 for Xxxxxxx, 00 for Luxembourg, 14 for Xxxxxxxxxxx, 00 (xxxxxx), 16 for Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Xxxxxxx, 00 for Xxxxxxx, 00 for Slovenia, 27 for Xxxxxxxx, 00 for Belarus, 29 for Xxxxxxx, 00 (xxxxxx), 00 xxx Xxxxxx xxx Xxxxxxxxxxx, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine, 47 for South Africa and 48 for New Zealand. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex Examples of arrangements of approval marks are given in annex 2 to this Regulation gives examples of arrangements of the approval markRegulation.

Approval. 5.1. Type approval shall only be granted if: (a) The vehicle If the two samples of a parking lamp type meets submitted in accordance with paragraph 3.2.3. above meet the requirements of paragraphs 6. and 7. belowthis Regulation, approval shall be granted. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of parking lamp. 5.3. Where approval is requested for a type of lighting and light-signalling device comprising a parking lamp and other lamps a single approval xxxx xxx be issued provided that the lamp in question complies with the requirements of this Regulation and that each of the other lamps forming part of the lighting and light- signalling device for which approval is requested, comply with the specific Regulation applying to them. 5.4. Notice of approval or of refusal or extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.45.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle Every parking lamp conforming to a vehicle type approved under this Regulation shall bear in the spaces referred to in paragraph 4.2. above, in addition to the marking prescribed in paragraph 4.1. an international approval mark xxxx consisting of: 5.4.15.5.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 2/ 5.4.25.5.2. The number of this Regulation, Regulation followed by the letter "R", a dash and the approval number to number; 5.5.3. When a lamp emits a light of amber colour towards the right front and rear, the lamp must be marked with an arrow indicating its orientation, the arrow showing the front of the circle prescribed in vehicle; 5.5.4. Where a single approval number is issued, as under paragraph 5.4.15.3. 5.5. If the vehicle conforms to , for a vehicle type approvedof lighting and light-signalling device comprising a parking lamp, under one or more and other Regulations annexed to the Agreementlamps, in the country which has granted a single approval under this Regulationxxxx xxx be affixed, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and consisting of the additional symbols of all prescribed by the various Regulations under which approval has been granted granted. 5.5.5. On devices with reduced light distribution in the country which has granted approval under conformity to paragraph 2.3. in Annex 4 to this Regulation shall be placed in a vertical columns to the right of the symbol prescribed in paragraph 5.4.1arrow starting from a horizontal segment and directed downwards. 5.6. The approval mark marking according to paragraphs 4.1.1. and 5.5. shall be clearly legible and be indelibleindelible even when the parking lamps are fitted on the vehicles. 2/ 1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Serbia, 11 for the United Kingdom, 12 for Xxxxxxx, 00 for Luxembourg, 14 for Xxxxxxxxxxx, 00 (xxxxxx), 16 for Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Xxxxxxx, 00 for Xxxxxxx, 00 for Slovenia, 27 for Xxxxxxxx, 00 for Belarus, 29 for Xxxxxxx, 00 (xxxxxx), 00 xxx Xxxxxx xxx Xxxxxxxxxxx, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Xxxxxxx, 00 for South Africa, 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant), 56 for Montenegro, 57 (vacant) and 58 for Tunisia. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary- General of the United Nations to the Contracting Parties to the Agreement. 5.7. The approval mark marking shall be clearly legible and indelible. It may be placed close to on an inner or outer part (transparent or not) of the device which cannot be separated from the transparent part of the device emitting the light. In any case the marking shall be visible when the device is fitted on the vehicle data plate affixed by or when a movable part such as the manufacturerhood or boot lid or a door is opened. 5.8. Annex 2 to this Regulation gives examples an example of arrangements an arrangement of the approval markxxxx.

Approval. 5.116.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation is provided with all the necessary specific equipment for the use of liquefied petroleum gases in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 17. below, approval of that vehicle type shall be granted. 5.216.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.316.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a an LPG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 16.3. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval.2 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4.1. above. 5.516.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.116.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.116.4.1. above. 5.616.6. The approval mark shall be clearly legible and be indelible. 5.716.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.816.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark.

Approval. 5.14.1. Type The procedures of Annex 3 shall be followed. 4.2. If the IWVTA type submitted for approval pursuant to this Regulation meets the relevant provisions of this Regulation, approval of that type shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. belowtaking into account paragraph 12.2. 5.24.3. An A type approval number shall be assigned to each IWVTA type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeapproved in accordance with Annex 8. 5.34.4. Notice of approval or of extension or of extension, refusal or withdrawal of approval or of production definitively discontinued of a vehicle an IWVTA type pursuant to this Regulation shall be communicated by means of a secure internet database in accordance with Schedule 5 of the 1958 Agreement to the Contracting Parties to the Agreement applying this Regulation, by means of a using the communication form conforming to the model in Annex 1 to this Regulation12. 5.44.5. There A type approval marking shall be affixed, as means to identify the IWVTA type, conspicuously and in a readily accessible place specified on in the approval forminformation document in Annex 5, to every vehicle conforming to a vehicle type an IWVTA type, approved under this Regulation an international Regulation. Such a type approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval; 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed marking shall be in paragraph 5.4.1accordance with Annex 2. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.64.6. The approval mark prescribed in paragraph 4.5. above may not be replaced by a Unique Identifier (UI) as referred to in Schedule 5 of the 1958 Agreement. 4.7. For vehicle systems as defined in paragraph 2.11. above the approvals of which are referenced in an IWVTA, no type approval markings need to be affixed. Approval markings for components as defined in paragraph 2.10. above need to be affixed as prescribed by the UN Regulations listed in Annex 4. 4.8. The type approval marking shall be clearly legible and be indelible. 5.74.9. The If a vehicle data plate is fitted by the manufacturer, the type approval mark marking shall be placed close to or on it. 4.10. For U-IWVTA the vehicle data plate affixed approval marking shall be in accordance with the template of Annex 2, Section I. For L-IWVTA the approval marking shall be in accordance with the template of Annex 2, Section II. 4.11. All variants and versions within one IWVTA type shall be approved within one IWVTA. 4.12. Approvals for all IWVTA types within one IWVTA class shall be handled by the manufacturersame approval authority. 5.84.13. Annex 2 A new IWVTA class is generated upon the granting of the first approval for an IWVTA type contained in this IWVTA class. Subsequent approvals for other IWVTA types may refer to this Regulation gives examples existing IWVTA class provided the conditions in paragraph 1.1. of arrangements of the approval markAnnex 7 are met.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that vehicle type shall be granted. 5.24.1.1. The Technical Service appointed in accordance with paragraph 12. below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same approval number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to by the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this RegulationRegulation and photographs and/or diagrams and drawings supplied by the applicant for approval, in a format not exceeding A4 (210 X 297 mm) or folded to that format and on an appropriate scale. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 2/; 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements approval marks. Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Xxxxxxx, 00 for Xxxxxxx, 00 for Slovenia, 27 for Xxxxxxxx, 00 for Belarus, 29 for Xxxxxxx, 00 (xxxxxx), 00 xxx Xxxxxx xxx Xxxxxxxxxxx, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Xxxxxxx, 00 for South Africa, 48 for New Zealand, 49 for Cyprus, 50 for Malta, 51 for the Republic of Korea, 52 for Malaysia, 53 for Thailand, 54 and 55 (vacant) and 56 for Montenegro. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the approval markUnited Nations to the Contracting Parties to the Agreement.

Approval. 5.116.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation is provided with all the necessary specific equipment for the use of liquefied petroleum gases in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 17. below, approval of that vehicle type shall be granted. 5.216.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.316.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a an LPG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 16.3. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval4. 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4. 5.516.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.116.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.116.4.1. 5.616.6. The approval mark shall be clearly legible and be indelible. 5.716.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.816.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval mark.

Approval. 5.14.1. Type If the power of the drive train submitted for approval shall only be granted if: (a) The vehicle type meets pursuant to this Regulation has been measured according to the requirements specifications of paragraphs 6. and 7paragraph 5. below, approval of the drive train type shall be granted. 5.24.2. An approval number shall be assigned to each drive train type approved. Its first two digits [(at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xx) Regulation in its original form)] shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle drive train type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle drive train type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 3a to this Regulation. 5.44.4. Notice of approval or of extension or of refusal of approval of vehicle type with regard to the drive train type pursuant to this Regulation shall be communicated to the Contracting Parties to the 1958 Agreement applying this Regulation by means of a form conforming to the model in Annex 3b to this Regulation. 4.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle drive train conforming to a vehicle drive train type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.5.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval2; 5.4.24.5.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.5.1. 5.54.5.3. Alternatively, instead of affixing these approval marks and symbols to the drive train, the manufacturer may decide that each drive train type approved under this Regulation shall be accompanied by a document giving this information so that the approval marks and symbol can be attached to the vehicle. 4.6. If the vehicle drive train conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5.1. above need not be repeated; in such a case case, the regulation Regulation and approval 2 The distinguishing numbers and of the additional symbols Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.2/Amend.3 - xxx.xxxxx.xxx/xxxxx/xxxx/xx00/xx00xxx/xx00xxx/xx00xxxxxxxxxxx.xxxx numbers of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5.1. 5.64.7. The approval mark xxxx shall be clearly legible and be indelible. 5.74.8. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed drive train identification figures provided by the manufacturer. 5.84.9. Annex 2 4 to this Regulation gives examples of the arrangements of the approval markxxxx.

Approval. 5.1. Type If the NORESS or component thereof submitted for approval shall only be granted if: (a) The vehicle type under this Regulation meets the requirements of paragraphs paragraph 6. and 7. below, approval for that type shall be granted. 5.2. An approval number shall be assigned to each NORESS type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxto the UN Regulation) shall indicate the series of amendments incorporating the most recent major technical amendments made to the UN Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of NORESS or component designed for, the same type(s) of vehicle. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to NORESS or component thereof under this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, affixed to every vehicle NORESS and component thereof conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. (a) A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;4 5.4.2. (b) The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1(a) above; (c) The approval number shall be indicated in the approval form, together with the method used for the approval tests. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly easily legible when the NORESS is fitted to the vehicle, and shall be indelible. 5.75.6. The A component may be marked with more than one approval mark shall number if it has been approved as a part of more than one NORESS; in this case the circle need not to be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8repeated. Annex 2 to this Regulation gives examples of arrangements an example of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe Regulation in respect of all the lights specified in the list, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approvalRegulation. The same Contracting Party shall may not assign the same number to another vehicle typetype or to the same vehicle type submitted with equipment not specified in the list referred to in paragraph 3.2.2. above subject to paragraph 7. of this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" ", followed by the distinguishing number of the country which has granted approval;approval2. 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.7. The approval xxxx shall be clearly legible and be indelible. 4.8. Annex 2 to this Regulation gives examples an example of the arrangements of the approval markmarks.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of that vehicle type shall be granted. 5.24.2. The conformity of the requirements in paragraph 5. shall be verified with the test procedure as defined in paragraph 6., however its operation shall not be limited to these specific test conditions. 4.3. An approval number shall be assigned to each vehicle type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxfor this Regulation in its initial form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the this Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of MOIS, or to another vehicle type. 5.34.4. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 and photographs and/or plans supplied by the applicant being in a format not exceeding A4 (210 x 297 mm), or folded to this Regulationthat format, and on an appropriate scale. 5.44.5. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model described in Annex 2, consisting ofof either: 5.4.14.5.1. A circle surrounding the letter "E" followed by by: (a) the distinguishing number of the country which has granted approval;approval;2 and 5.4.2. The (b) the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1this paragraph; or 4.5.2. An oval surrounding the letters "UI" followed by the Unique Identifier. 5.54.6. If the vehicle conforms to a vehicle type approved, approved under one or more other UN Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.5. above need not be repeated; in . In such a case case, the regulation UN Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.5. above. 5.64.7. The approval mark shall be clearly legible and be indelible. 5.74.8. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the power of the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7paragraph 5. below, approval of the engine type or family shall be granted. 5.24.2. An approval number shall be assigned to each engine type or family approved. Its first two digits (at present 00 corresponding to 02 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeengine type or family. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval of an engine type or of production definitively discontinued of a vehicle type an engine family pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place as specified on the approval form, to every vehicle engine conforming to a vehicle an engine type or an engine family approved under this Regulation an international approval mark a statutory marking consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. Where the statutory marking of the engine is not visible without removing parts, the vehicle manufacturer shall affix to the category T vehicle or the non- road mobile machinery, in a visible manner, a duplicate of the marking provided by the manufacturer. 5.54.5. If the vehicle engine conforms to a vehicle an approved type approved, or family under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark statutory marking shall be placed close to or on the vehicle data plate affixed by the manufacturermanufacturer to the approved type. 5.84.7. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.8. Every engine conforming to an engine type or an engine family approved under this Regulation must bear, in addition to the approval mark.xxxx: (a) The trademark or trade name of the manufacturer of the engine and the address at which it can be contacted;

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 12 September 20xx1995) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 2/ 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1.; and 4.4.3. an additional symbol consisting of the letter A or B indicating the Class in which the vehicle has been approved. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that vehicle type shall be granted. 5.24.1.1. The Technical Service appointed in accordance with paragraph 11. below shall check whether the required conditions have been satisfied. 4.1.2. In case of doubt, account shall be taken, when verifying the conformity of the vehicle to the requirements of this Regulation, of any data or test results provided by the manufacturer which can be taken into consideration in validating the approval test carried out by the Technical Service. 4.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue approved in accordance with Schedule 4 of the approval. The same Contracting Party shall not assign the same number to another vehicle typeAgreement (E/ECE/TRANS/505/Rev.3). 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark conforming to the model given in Annex 2 consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval2; 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other UN Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation and approval additional numbers and the additional symbols of all the UN Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the type submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe relevant parts of this Regulation, approval of that type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1, Part 1 or 2 as appropriate to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or REESS or separate technical unit conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval.3 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.4.1. 5.54.4.3. In the case of an approval of a REESS or a separate technical unit of the REESS the "R" shall be followed by the symbol "ES". 4.5. If the vehicle or REESS conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark xxxx shall be clearly legible and shall be indelible. 5.74.6.1. The In the case of a vehicle, the approval mark xxxx shall be placed on or close to or on the vehicle data plate affixed by the manufacturer. 5.84.6.2. In the case of a REESS or separate technical unit approved as a REESS, the approval xxxx shall be affixed on the major element of the REESS by the manufacturer. 4.7. Annex 2 to this Regulation gives examples of the arrangements of the approval markxxxx.

Approval. 5.1. Type If the RESS or component thereof submitted for approval shall only be granted if: (a) The vehicle type under this Regulation meets the requirements of paragraphs paragraph 6. and 7. below, approval for that type shall be granted. 5.2. An approval number shall be assigned to each RESS type approved. Its first two digits (at present 00 01 corresponding to the 00 01 series of amendments which entered into force on 01 September 20xxto the Regulation) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype of RESS or component designed for, the same type(s) of motor cycle. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to RESS or component thereof under this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, affixed to every vehicle RESS and component thereof conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.1. (a) A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 3; 5.4.2. (b) The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1(a) above; (c) The approval number shall be indicated in the approval form, together with the method used for the approval tests. 5.5. If The approval xxxx shall be easily legible when the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed RESS is fitted to the Agreementvehicle, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1indelible. 5.6. The A component may be marked with more than one approval mark shall number if it has been approved as a part of more than one RESS; in this case the circle need not to be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8repeated. Annex 2 to this Regulation gives examples of arrangements an example of the approval markxxxx.

Approval. 5.14.1. Type approval shall only be granted if: (a) The vehicle If the two samples of a type meets of cornering lamp meet the requirements of paragraphs 6. and 7. belowthis Regulation, approval shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3type of cornering lamp covered by this Regulation. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type of cornering lamp pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.3. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle Every cornering lamp conforming to a vehicle type approved under this Regulation an shall bear in the space referred to in paragraph 3.3. above, in addition the mark and the particulars prescribed above in paragraphs 3.1., 3.2. and 3.3. or 3.4. respectively: 4.3.1. An international approval mark consisting of: 5.4.14.3.1.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalthe approval;2 and 4.3.1.2. An approval number; 5.4.24.3.2. An additional symbol consisting of the letter "K" as shown in Annex 2 to this Regulation. 4.3.3. The first two digits (at present 01)3 of the approval number which indicate the most recent series of amendments to this Regulation may be placed in the vicinity of the additional letter "K". 4.4. When two or more lamps are part of the same assembly of grouped, combined or reciprocally incorporated lamps, approval is granted only if each of these lamps satisfies the requirements of this Regulation or of another Regulation. Lamps not satisfying any one of those Regulations shall not be part of such an assembly of grouped, combined or reciprocally incorporated lamps. 4.4.1. Where grouped, combined or reciprocally incorporated lamps comply with the requirements of several Regulations, a single international approval mark may be xxxxxxx, consisting of a circle surrounding the letter "E" followed by the letter "R", a dash and the approval distinguishing number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted the approval, an approval under this Regulationnumber and, if necessary, the required arrow. This approval mark 2 The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3)(ECE/TRANS/WP.29/78/Rev.6) 3 The 02 series of amendments does not require changes in the approval number (TRANS/WP.29/815, para. 82). may be placed anywhere on the grouped, combined or reciprocally incorporated lamps provided that; 4.4.1.1. It is visible after their installation; 4.4.1.2. No part of the grouped, combined or reciprocally incorporated lamps that transmits light can be removed without at the same time removing the approval mark. 4.4.2. The identification symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations for each lamp appropriate to each Regulation under which approval has been granted in granted, together with the country which has granted approval under this corresponding series of amendments incorporating the most recent major technical amendments to the Regulation at the time of issue of the approval, shall be placed marked: 4.4.2.1. Either on the appropriate light-emitting surface; 4.4.2.2. Or in vertical columns to the right a group, in such a way that each lamp of the symbol prescribed grouped, combined or reciprocally incorporated lamps may be clearly identified (see three possible examples in paragraph 5.4.1Annex 2). 5.64.4.3. The size of the components of a single approval mark shall not be less than the minimum size required for the smallest of the individual marks by a Regulation under which approval has been granted. 4.4.4. An approval number shall be assigned to each type approved. The same Contracting Party may not assign the same number to another type of grouped, combined or reciprocally incorporated lamps covered by this Regulation. 4.5. The mark and symbol referred to in paragraphs 4.3.1. and 4.3.2. shall be indelible and shall be clearly legible even when the cornering lamp is mounted on the vehicle. 4.6. Annex 2 gives examples of approval marks for a single lamp (Figure 1) and for grouped, combined or reciprocally incorporated lamps (Figure 2) with all the additional symbols referred to above, in which the letter "K" indicates a cornering lamp. 4.7. The approval mark marking shall be clearly legible and indelible. It may be indelible. 5.7placed on an inner or outer part (transparent or not) of the device which cannot be separated from the transparent part of the device emitting the light. The approval mark In any case the marking shall be placed close to or visible when the device is fitted on the vehicle data plate affixed by or when a movable part such as the manufacturerhood or boot lid or a door is opened. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval pursuant to this Regulation meets the requirements of paragraphs 6. and 7Paragraph 5. below, approval of that vehicle shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its ; its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to the same vehicle type equipped with another type of AEBS, or to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, Regulation by means of a form conforming to the model in Annex 1 and documentation supplied by the applicant being in a format not exceeding A4 (210 × 297mm), or folded to this Regulationthat format, and on an appropriate scale or electronic format. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark xxxx conforming to the model described in Annex 2, consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;; 1 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations Regulations, annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1Paragraph 4.4.1. above. 5.64.6. The approval mark xxxx shall be clearly legible and be indelible. 5.74.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.1. Type approval shall only be granted if: (a) The vehicle type meets the requirements of paragraphs 6. and 7. below. 5.24.1. An approval number shall be assigned to each approved type approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue in accordance with Schedule 4 of the approval. The same Contracting Party shall not assign the same number to another vehicle typeAgreement (E/ECE/TRANS/505/Rev.3). 5.34.2. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1, Part 1 or 2 as appropriate to this Regulation. 5.44.3. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or REESS conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.3.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval‡. 5.4.24.3.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.3.1. 5.54.3.3. In the case of an approval of a REESS the "R" shall be followed by the symbol "ES". 4.4. If the vehicle or REESS conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.3.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.3.1. 5.64.5. The approval mark shall be clearly legible and shall be indelible. 5.74.5.1. The In the case of a vehicle, the approval mark shall be placed on or close to or on the vehicle data plate affixed by the manufacturer. 5.84.5.2. In the case of a REESS, the approval mark shall be affixed on the major element of the REESS by the manufacturer. 4.6. Annex 2 to this Regulation gives examples of the arrangements of the approval mark.

Approval. 5.1. Type 5.1 If the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation, meets the requirements of paragraphs 6. and 7. paragraph 6 below, approval of the engine type shall be granted. 5.2. 5.2 An approval number shall be assigned to each engine type approved. Its approved .Its first two digits (at present 00 03 corresponding to the 00 03 series of amendments which entered into force on 01 September 20xx20 April 1986) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle engine type. 5.3. 5.3 Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle an engine type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 annex 2 to this Regulation.. UN ECE Regulation 24/03 3 5.4. 5.4 There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle engine conforming to a vehicle an engine type approved under this Regulation an international approval mark consisting of: 5.4.1. 5.4.1 A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 1/ 5.4.2. 5.4.2 The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1, 5.4.3 The following additional symbol, a rectangle surrounding a figure expressing in m-1 the absorption coefficient obtained, at the time of approval, during the tests under free acceleration and determined by the procedure described in annex 5 of this Regulation. 5.55.4.4 Alternatively instead of affixing these approval marks and symbols to the engine the manufacturer may decide that each engine type approved under this Regulation shall be accompanied by a document giving this information so that the approval marks and symbol can be attached to the vehicle in accordance with paragraph 14.4 of this Regulation. 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 10 for Yugoslavia, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 14 for Switzerland, 15 (vacant), 16 for Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Ireland, 25 for Croatia, 26 for Slovenia, 27 for Slovakia, 28 for Belarus, 29 for Estonia, 30 (vacant), 31 for Bosnia and Herzegovina, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35-36 (vacant), 37 for Turkey, 38-39 (vacant), 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine and 47 for South Africa. Subsequent numbers shall be assigned to other countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement. UN ECE Regulation 24/03 4 5.5 If the vehicle engine conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. 5.4.1 need not be repeated; : in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. 5.6 The approval mark shall be clearly legible and be indelible. 5.7. 5.7 The approval mark shall be placed close to or on the vehicle data plate affixed engine identification figures provided by the manufacturer. 5.8. 5.8 Annex 2 3 to this Regulation gives examples of the arrangements of the approval markxxxx.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 5, 6. , and 7. 7 below, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 02, corresponding to the 00 02 series of amendments which entered into force on 01 3 September 20xx1997) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 3/; 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 3 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type If the type submitted for approval shall only be granted if: (a) The vehicle type to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 00, corresponding to the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments amendment made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another type of vehicle typeor component as defined in this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or component conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval,3 and 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle a type conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of all the Regulations Regulation under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The In the case of a vehicle, the approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. In the case of a component approved separately as an immobilizer, the approval mark shall be affixed by the manufacturer to the major element(s) of the device. In the case of a component approved as an immobilizer under this regulation and an alarm system under UN Regulation No. 162 or UN Regulation No. 116, Supplement 7 to the original version, or UN Regulation No. 97 Supplement 8 to the 01 series of amendments both approval marks shall be affixed by the manufacturer to the major element(s) of the device. 4.9. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.10. As an alternative to the approval markmark described in paragraph 4.4. above, a certificate of conformity shall be issued for every immobilizer offered for sale. Where an immobilizer manufacturer supplies an unmarked immobilizer approved to this Regulation to a vehicle manufacturer, for fitment by that manufacturer as original equipment for a vehicle model or range of vehicle models, the immobilizer manufacturer shall supply a number of copies of the certificate of conformity to the vehicle manufacturer, sufficient for that manufacturer to obtain the vehicle approval of this Regulation. If the immobilizer is made up of separate components, its main component(s) shall bear a reference mark and the certificate of conformity shall provide a list of such reference marks. A model of the certificate of conformity is given in Annex4 to this Regulation. 4.11. When an immobilizer, approved to this Regulation or UN Regulation No. 116, Supplement 7 to the original version, or UN Regulation No. 97, Supplement 8 to the 01 series of amendments as a separate technical unit, is installed in a vehicle submitted for approval to this Regulation, tests required to be passed by an immobilizer in order to obtain approval to this Regulation shall not be repeated.

Approval. 5.14.1. Type If the tractor type submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. paragraph 5 below, approval of that tractor type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typetractor type as defined in paragraph/2.3. above. 5.34.3. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively definitely discontinued of a vehicle tractor type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex annex 1 to this Regulation. 5.44.4. There To every tractor conforming to a type approved pursuant to this Regulation there shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;; 1/ 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.1paragraph/0.0.0. 5.54.5. If the vehicle tractor conforms to a vehicle tractor type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle tractor data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.14.1. Type If the type submitted for approval shall only be granted if: (a) The vehicle type to this Regulation meets the requirements of paragraphs 6. and 7. belowthis Regulation, approval of that type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 00, corresponding to the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments amendment made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another type of vehicle typeor component as defined in this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties to the Agreement applying this Regulation, Regulation by means of a form conforming to the model in Annex 1 2 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle or component conforming to a vehicle type approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval,2 and 5.4.24.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number number, to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.5. If the vehicle a type conforms to a vehicle type approved, under one or more other UN Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of all the Regulations Regulation under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The In the case of a vehicle, the approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 3 to this Regulation gives examples of arrangements of the approval markmarks.

Approval. 5.1. Type Approval for a type of glazing If the samples submitted for approval shall only be granted if: (a) The vehicle type meets meet the requirements of paragraphs 6. and 7to 8. belowof this Regulation, approval of the pertinent type of safety glazing material shall be granted. 5.2. An approval number shall be assigned to each type as defined in annexes 5, 7, 11, 12, 14, 15 and 16 or, in the case of windscreens, to each group approved. Its first two digits (at present 00 corresponding to for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype or group of safety glazing material. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or refusal of production definitively discontinued approval of a vehicle type of safety glazing material pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex annex 1 - and its appendices - to this Regulation. 5.3.1. In the case of windscreens, the notice of approval shall be accompanied by a document listing every windscreen model in the approved group, together with the characteristics of the group pursuant to annex 1, appendix 8. 5.4. There shall be affixed, affixed conspicuously and in a readily accessible place specified on the approval form, to every vehicle piece of glazing and double-glazed unit conforming to a vehicle type approved under this Regulation Regulation, in addition to the marking prescribed in paragraph 4.1., an international approval mark consisting xxxx. Any specific approval xxxx assigned to each pane forming a double-glazed unit may also be affixed. This approval xxxx shall consist of: 5.4.1. A a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approvalapproval 1/; 5.4.2. The the number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If The following additional symbols shall be affixed near the vehicle conforms above approval xxxx: 5.5.1. in the case of a windscreen : I for toughened glass (I/P if faced) 2/ II for ordinary laminated glass (II/P if faced) 2/ III for treated laminated glass (III/P if faced) 2/ IV for glass-plastics glazing. 5.5.2. V in the case of safety glazing having a regular light transmittance less than 70 per cent. 5.5.3. VI in the case of double-glazed unit 5.5.4. VII in the case of uniformly-toughened glass panes which can be used as windscreens for slow-moving vehicles which, by construction, cannot exceed 40 km/h. Norway, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 22 for the Russian Federation, 23 for Greece, 24 for Xxxxxxx, 00 for Xxxxxxx, 00 for Slovenia, 27 for Xxxxxxxx, 00 for Belarus, 29 for Xxxxxxx, 00 (xxxxxx), 00 xxx Xxxxxx xxx Xxxxxxxxxxx, 32 for Latvia, 33 (vacant), 34 for Bulgaria, 35 (vacant), 36 for Lithuania, 37 for Turkey, 38 (vacant), 39 for Azerbaijan, 40 for The former Yugoslav Republic of Macedonia, 41 (vacant), 42 for the European Community (Approvals are granted by its Member States using their respective ECE symbol), 43 for Japan, 44 (vacant), 45 for Australia, 46 for Ukraine, 47 for South Africa and 48 for New Zealand. Subsequent numbers shall be assigned to a vehicle type approvedother countries in the chronological order in which they ratify or accede to the Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, under one or more other Regulations annexed Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions, and the numbers thus assigned shall be communicated by the Secretary-General of the United Nations to the Contracting Parties to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed . 2/ As defined in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.12.3. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.116.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation is provided with all the necessary specific equipment for the use of liquefied petroleum gases in its propulsion system and meets the requirements of paragraphs 6. and 7paragraph 17. below, approval of that vehicle type shall be granted. 5.216.2. An approval number shall be assigned to each type of vehicle approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.316.3. Notice of approval or of extension refusal or of refusal or withdrawal extension of approval or of production definitively discontinued of a an LPG vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 2D to this Regulation. 5.416.4. There shall be affixed, conspicuously and in a readily accessible place space specified on the approval formform referred to in paragraph 16.3. above, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.116.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval 3/. 5.4.216.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.116.4. 5.516.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.116.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.116.4.1. 5.616.6. The approval mark xxxx shall be clearly legible and be indelible. 5.716.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturerplate. 5.816.8. Annex 2 2C to this Regulation gives examples of arrangements the arrangement of the aforesaid approval markxxxx.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. paragraph 5 below and 7. belowAnnexes 3, 4, 5 and 7 to this Regulation, approval of this vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.34.3. Notice of approval or of extension refusal or of refusal extension or withdrawal of approval or of production definitively definitely discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter Letter "E" followed by the distinguishing number of the country which has granted approval;approval1. 5.4.24.4.2. The number of this Regulation, followed by the letter Letter "R", a dash and the approval number to the right of the circle prescribed described in paragraph 5.4.14.4.1. 5.54.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, Agreement in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. need not be repeated; in such a this case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. 5.64.6. The approval mark shall be clearly legible and shall be indelible. 5.74.7. The approval mark shall be placed on or close to or on the vehicle data plate affixed by the manufacturerManufacturer. 5.84.8. Annex 2 to this Regulation gives examples of the arrangements of the approval mark.

Approval. 5.14.1. Type If the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to paragraph 3.1. of this Regulation meets the requirements of paragraphs 6. and 7paragraph 5.2. below, approval of that type of engine or family of engines shall be granted. 5.24.2. An approval number shall be assigned to each type or family approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeengine type or family. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval of an engine type or of production definitively discontinued of a vehicle type family pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 2, as applicable, to this Regulation. Values measured during the type test shall also be shown. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle engine conforming to a vehicle an engine type or family approved under this Regulation Regulation, an international approval mark xxxx consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.4.3. An additional symbol consisting of two letters, the first of which shall be a letter from D to R indicating the emission level (paragraph 5.2.1. below) according to which the engine or the engine family has been approved, the second of which shall be either the letter A if the engine family is certified for variable speed operation or the letter B if the engine family is certified for constant speed operation. 4.5. If the vehicle engine conforms to a vehicle an approved type approved, or family under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.2. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturermanufacturer to the approved type. 5.84.7. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.8. The engine approved as a technical unit shall bear, in addition to the approval markxxxx: 4.8.1. The trademark or trade name of the manufacturer of the engine; 4.8.2. The manufacturer's engine code; 4.9. These marks shall be clearly legible and indelible.

Approval. 5.14.1. Type If the engine submitted for approval shall only be granted if: (a) The vehicle type pursuant to paragraph 3.1. of this Regulation meets the requirements of paragraphs 6. and 7paragraph 5.2. below, approval of that type of engine or family of engines shall be granted. 5.24.2. An approval number shall be assigned to each type or family approved. Its first two digits (at present 00 corresponding to the 00 series of amendments which entered into force on 01 September 20xx) shall indicate the series of amendments (at present 01) incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle typeengine type or family. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval of an engine type or of production definitively discontinued of a vehicle type family pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 2, as applicable, to this Regulation. Values measured during the type test shall also be shown. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle engine conforming to a vehicle an engine type or family approved under this Regulation Regulation, an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval2;‌ 5.4.24.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. 5.54.4.3. An additional symbol consisting of a letter from D to R indicating the emission level (paragraph 5.2.1.) according to which the engine or the engine family has been approved. 4.5. If the vehicle engine conforms to a vehicle an approved type approved, or family under one or more other Regulations annexed Annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case case, the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.2. 5.6. The approval mark shall be clearly legible and be indelible. 5.74.6. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturermanufacturer to the approved type. 5.84.7. Annex 2 3 to this Regulation gives examples of arrangements of approval marks. 4.8. The engine approved as a technical unit shall bear, in addition to the approval mark: 4.8.1. The trademark or trade name of the manufacturer of the engine; 4.8.2. The manufacturer's engine code; 4.9. These marks shall be clearly legible and indelible.

Approval. 5.1. Type approval shall only be granted if: (a) The if the vehicle type meets the requirements of paragraphs 6. and 7. below. 5.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 04 corresponding to the 00 04 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign the same number to another vehicle type. 5.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;3 5.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.1. 5.5. If the vehicle conforms to a vehicle type approved, approved under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.1. need not be repeated; in such a case the regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.1. 5.6. The approval mark shall be clearly legible and be indelible. 5.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.8. Annex 2 to this Regulation gives examples of arrangements of the approval mark.

Approval. 5.14.1. Type If the vehicle submitted for approval shall only be granted if: (a) The vehicle type pursuant to this Regulation meets the requirements of paragraphs 6. and 7. belowthe Regulation in respect of all the devices specified in the list, approval of that vehicle type shall be granted. 5.24.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 01 for the 00 Regulation in its 01 series of amendments which entered into force on 01 September 20xxamendments) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle typetype or to the same vehicle type submitted with equipment not specified in the list referred to in paragraph 3.2.2. above, subject to the provisions of paragraph 7. of this Regulation. 5.34.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the Agreement applying which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. 5.44.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of: 5.4.14.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;approval;2 5.4.24.4.2. The number of this Regulation, Regulation followed by the letter "R", a dash dash, and the approval number to the right of the circle prescribed in paragraph 5.4.14.4.1. above. 5.54.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.14.4.1. above need not be repeated; in such a case the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.14.4.1. above. 5.64.6. The approval mark shall be clearly legible and be indelible. 5.74.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.84.8. Annex 2 to this Regulation gives examples of arrangements the arrangement of the approval markmarks.

Approval. 5.115.1. Type approval shall only be granted if: (a) The If the vehicle type submitted for approval in accordance with paragraph 14 above meets the requirements of paragraphs 6. and 7. belowparagraph 16 of this Regulation, approval shall be granted. 5.215.2. An approval number shall be assigned to each type approved. Its first two digits (at present 00 corresponding to 00, for the 00 series of amendments which entered into force on 01 September 20xxRegulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall may not assign the same number to another vehicle type. 5.315.3. Notice of approval or of extension or of refusal or withdrawal of approval or of production definitively discontinued of a vehicle type pursuant to this Regulation shall be communicated to the Parties to the 1958 Agreement applying this Regulation, by means of a form conforming to the model in Annex 1 annex 2 to this Regulation. 5.415.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark xxxx consisting of: 5.4.115.4.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted approval;, */ 5.4.215.4.2. The number of this Regulation, followed by the letter "R", a dash and the approval number to the right of the circle prescribed in paragraph 5.4.115.4.1. 5.515.5. If the vehicle conforms to a vehicle type approved, under one or more other Regulations annexed to the Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 5.4.115.4.1. need not be repeated; in such a case case, the regulation Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 5.4.115.4.1. 5.615.6. The approval mark xxxx shall be clearly legible and be indelible. 5.715.7. The approval mark xxxx shall be placed close to or on the vehicle data plate affixed by the manufacturer. 5.815.8. Annex 2 4 to this Regulation gives examples of arrangements of the approval markxxxx.