Agreement of Certification Criteria Sample Clauses

Agreement of Certification Criteria. The AR should review the FAA’s proposed U.S. type certification basis and notify the FAA Project Manager of the proposed method of compliance. The FAA may accept one of two compliance methods: the U.S. Type Certification Basis or the Russian Type Certification Basis plus all FAA Additional Technical Conditions (ATCs).
Sample 1
AutoNDA by SimpleDocs
Agreement of Certification Criteria. The DCA should review the FAA’s proposed U.S. type certification basis and notify the FAA Project Manager of the proposed means of compliance. If the DCA chooses to use its domestic airworthiness and environmental standards, the FAA will start the process of developing additional technical conditions such that the U.S. type certification basis can be met. The FAA will coordinate with the DCA in the development of additional technical conditions to allow the FAA to benefit from the technical expertise of the DCA and, if requested by the FAA, allows the DCA to make a proper determination of compliance.
Sample 1

Related to Agreement of Certification Criteria

  • Resume Self-Certification Form When submitting a response to an RFQ the Contractor shall submit with its response a completed and signed Resume Self-Certification Form (Contract Exhibit F) to the Customer for each proposed Staff member identified in the RFQ response.

  • Reliance on Self-Certifications and Documentary Evidence A Reporting Financial Institution may not rely on a self-certification or documentary evidence if the Reporting Financial Institution knows or has reason to know that the self- certification or documentary evidence is incorrect or unreliable.

  • Certification of Coverage Engineer shall furnish County with a certification of coverage issued by the insurer. Engineer shall not cause any insurance to be canceled nor permit any insurance to lapse. In addition to any other notification requires set forth hereunder, Engineer shall also notify County, within twenty-four (24) hours of receipt, of any notices of expiration, cancellation, non-renewal, or material change in coverage it receives from its insurer.

  • AS9100 Certification ‌ AS9100 Certification, specifies requirements for a quality management system to demonstrate the Contractor’s ability to consistently meet the customer requirements as well as statutory and regulatory requirements for the aerospace industry. An AS9100 Certification, is not mandatory; however, Contractors who desire to compete for work within the aerospace industry are encouraged to have AS9100 Certification, during the entire term of OASIS. The Contractor shall notify the OASIS CO, in writing, if there are any changes in the status of their AS9100 Certification, and provide the reasons for the change and copies of audits from an AS9100 Certification Body, as applicable. If only part of a Contractor’s organization is AS9100, certified, the Contractor shall make the distinction between which business units or sites and geographic locations have been certified.

  • Certification of Contractor The Contractor shall certify, over his own signature, that the Work provided for by the Contract Documents has been completed under the terms and conditions thereof, and that the entire balance of the contract is due and payable.

  • ISO 9001 Certification The Contractor shall maintain or exceed their ISO 9001 Certification and submit updates, if applicable

  • Instructions for Certification – First Tier Participants a. By signing and submitting this proposal, the prospective first tier participant is providing the certification set out below.

  • Instructions for Certification 1. By signing and submitting this CONTRACT, the prospective lower tier participant is providing the certification set out below.

  • COMPLIANCE AND CERTIFICATION 25.1 Each Party shall comply at its own expense with all Applicable Laws that relate to that Party’s obligations to the other Party under this Agreement. Nothing in this Agreement shall be construed as requiring or permitting either Party to contravene any mandatory requirement of Applicable Law.

  • Certification of Compliance The Owner may permit the use, prior to sampling and testing, of certain materials or assemblies when accompanied by manufacturer's certificates of compliance stating that such materials or assemblies fully comply with the requirements of the contract. The certificate shall be signed by the manufacturer. Each lot of such materials or assemblies delivered to the work must be accompanied by a certificate of compliance in which the lot is clearly identified. Materials or assemblies used on the basis of certificates of compliance may be sampled and tested at any time and if found not to be in conformity with contract requirements will be subject to rejection whether in place or not. The form and distribution of certificates of compliance shall be as approved by the Owner. When a material or assembly is specified by "brand name or equal" and the Contractor elects to furnish the specified "brand name", the Contractor shall be required to furnish the manufacturer's certificate of compliance for each lot of such material or assembly delivered to the work. Such certificate of compliance shall clearly identify each lot delivered and shall certify as to:

Time is Money Join Law Insider Premium to draft better contracts faster.