Resist coating definition

Resist coating means a coating that is applied to a plastic part before metallic plating to prevent deposits of metal on portions of the plastic part.
Sample 1Sample 2Sample 3
Resist coating means a coating that is applied to a plastic part before metallic plating to
Sample 1

Examples of Resist coating in a sentence

  • This exception applies only if substitute compliant coatings are not available.(3) The requirements of subsection (d) do not apply to the application of the following coatings to automotive-transportation and business machine parts:(i) Texture coat.(ii) Vacuum-metalizing coating.(iii) Gloss reducer.(iv) Texture topcoat.(v) Adhesion primer.(vi) Electrostatic prep coat.(vii) Resist coating.

  • While reasonable efforts have been made to ensure that the contents of this publication are factually correct, the GMRG and its advisors, NERA Economic Consulting and Johnson Winter & Slattery, do not accept responsibility for the accuracy or completeness of the contents, and shall not be liable for any loss or damage that may be occasioned directly or indirectly through the use of, or reliance on, the contents of this publication.

  • Resist coating process for blanks is excluded from the Licensed Know-how and shall not be transferred, however, basic information of the material and thickness of resist (not the coating process) will be provided by DNP upon Company’s request , provided that the Company will not disclose such basic information of the material and thickness of resist to any blanks manufacturer.

  • Resist coating step: • Cover spinning plate with blue tape to protect the back of sample and vacuum chuck.

  • SiResistSiResistResist coating Partial exposure(a) (b) SiResist Resist SiResist developpment RIE(c) (d) e SiResist removal(e) Figure 2.9: Transversal cross section showing the master stamp fab- rication in a single step with the grating and waveguide features (a) Resist coating with the optimized thickness to completely etch the trenches defining the waveguide height.

  • Resist coating by spray technology on high topography wafer structure is also investigated by Suriadi et al.

  • Resist coating, post apply bake (PAB) and exposure: photo acid generation and precise transfer of aerial image into resist, highly dependent from substrate condition, resist film thickness, resist film condition (stress), surface condition (distribution of polymer, PAG, quencher, solvent, etc.).

  • We applied the same methodology to accounts under threat, as we only wanted to look at accounts which were being threatened by competition not closure.

Related to Resist coating

  • Flat coating means a coating that is not defined under any other definition in this section and that registers gloss less than 15 on an 85-degree meter or less than 5 on a 60-degree meter.

  • Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, and stains.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Floor coating means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces which may be subject to foot traffic.

  • Pretreatment coating means a coating which contains no more than 12% solids by weight, and at least 0.5% acid by weight, is used to provide surface etching, and is applied directly to metal surfaces to provide corrosion resistance, adhesion, and ease of stripping.

  • Undercoating means any aerosol product designed to impart a protective, non-paint layer to the undercarriage, trunk interior, and/or firewall of motor vehicles to prevent the formation of rust or to deaden sound. “Undercoating” includes, but is not limited to, rubberized, mastic, or asphaltic products.

  • Roll coating means the application of a coating material to a substrate by means of hard rubber or steel rolls.

  • Flow coating means a coating labeled and formulated exclusively for use by electric power companies or their subcontractors to maintain the protective coating systems present on utility transformer units.

  • Metallic coating means a coating which contains more than five grams of metal particles per liter of coating, as applied. Metal particles are pieces of a pure elemental metal or a combination of elemental metals.

  • Nuclear coating means any protective coating used to seal porous surfaces, such as steel or concrete, that otherwise would be subject to intrusion by radioactive materials. These coatings must be resistant to long term (service life) cumulative radiation exposure (ASTM D4082-83**), relatively easy to decontaminate (ASTM D4256-83**), and resistant to various chemicals to which the coatings are likely to be exposed (ASTM 3912-80**). General protective requirements are outlined by the Department of Energy (formerly United States Atomic Energy Commission Regulatory Guide 1.54**).

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Air dried coating means a coating that is dried by the use of air or forced warm air at temperatures up to 1940F (900C).

  • Clear coating means a transparent coating designed to provide the final gloss and resistance properties of the coating system;

  • Automotive windshield washer fluid means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

  • Repair coating means a coating used to re-coat portions of a previously coated product which has sustained mechanical damage to the coating following normal coating operations.

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Oxides of nitrogen means the sum of the volume mixing ratio (ppbv) of nitrogen monoxide (nitric oxide) and nitrogen dioxide expressed in units of mass concentration of nitrogen dioxide (µg/m3);

  • Faux finishing coating means a coating labeled and formulated as a stain or a glaze to create artistic effects including, but not limited to, dirt, old age, smoke damage, and simulated marble and wood grain.

  • Dip coating means the application of a coating material to a substrate by dipping the part into a tank of the coating material.

  • Filtration means a process for removing particulate matter from water by passage through porous media.

  • Exfiltration means any unauthorized release of data from within an information system. This includes copying the data through covert network channels or the copying of data to unauthorized media.

  • Dusting aid means a product designed or labeled to assist in removing dust and other soils from floors and other surfaces without leaving a wax or silicone based coating. “Dusting Aid” does not include “Pressurized Gas Duster.”

  • Specialty coating means any coating that is manufactured and used for one (1) of the following specialized applications:

  • Low-solids coating means a coating containing 0.12 kilogram or less of solids per liter (one pound or less of solids per gallon) of coating material.

  • Nitrogen oxides means nitric oxide and nitrogen dioxide, expressed as nitrogen dioxide (NO2);

  • Infiltration means water other than wastewater that enters a sewer system (including sewer system and foundation drains) from the ground through such means as defective pipes, pipe joints, connections, or manholes. Infiltration does not include, and is distinguished from, inflow.