EPA protocol gas definition

EPA protocol gas means a calibration gas mixture prepared and analyzed according to section two of the "EPA Traceability Protocol for Assay and Certification of Gaseous Calibration Standards," May 2012, EPA-600/R-12/531, or such revised procedure as approved by the administrator.
Sample 1Sample 2Sample 3
EPA protocol gas means a calibration gas mixture prepared and analyzed according to section two of the "EPA Traceability Protocol for Assay and Certification of Gaseous Calibration Standards," September 1997, as amended August 25, 1999May 2012, EPA-600/R97/121R-12/531, or such revised procedure as approved by the administrator.
Sample 1Sample 2

Examples of EPA protocol gas in a sentence

  • While we agree the disturbance will be of relatively short duration, we consider the water quality and sedimentation effects will impact a large portion of the Walls Bay CMA.

  • The ratio of a unit’s annual heatinput (in million British thermal units or equivalent units of measure) to the unit’s maximum rated hourly heat input rate (in million British thermal units per hour or equivalent units of measure) times 8,760 hours.* * * * * EPA protocol gas * * * On and after January 1, 2009, vendors advertisingcertification with the EPA Traceability Protocol or distributing gases as ‘‘EPA Protocol Gas’’ must participate in the EPA Protocol Gas Verification Program.

  • Input concentrations are generated using an onsite dynamic dilution calibrator and EPA protocol gas cylinder ( 40 CFR Part 58 App A Sec 3.1.1).

  • Calibration of these instruments and audits of their performance are done using the EPA protocol gas mixtures containing a certified concentration of SO2 in nitrogen.

  • EPA protocol gas standards were used to calibrate the O2/CO2 analyzer.

  • Per EPA protocol gas specifications, the actual concentration must be within ± 2 percent of the certified tag value.

  • Calibration of the instrument and audits of their performance are done using the EPA protocol gas mixtures containing a known concentration of Nitric Oxide (NO) and Nitrogen Oxides (NOx) in nitrogen.

  • Calibration of the instrument and audits of their performance are done using an EPA protocol gas mixtures containing a known concentration of Nitric Oxide (NO) and Nitrogen Oxides (NOx) in nitrogen.

  • Set up the gas dilution system to provide calibration gases by diluting an EPA protocol gas standard for a gas of interest (SO2, CO, O2, NO, or NO2).

  • DEQ Office of Air Quality Monitoring (AQM) owns one (1) audit gas cylinder (“gas cylinder”) that contains EPA protocol gas that expired before all of the gas was used (i.e. the cylinder still contain gas).

Related to EPA protocol gas

  • ERCOT Protocols means the document adopted by ERCOT, including any attachments or exhibits referenced in that document, as amended from time to time, that contains the scheduling, operating, planning, reliability, and settlement (including customer registration) policies, rules, guidelines, procedures, standards, and criteria of ERCOT. For the purposes of determining responsibilities and rights at a given time, the ERCOT Protocols, as amended in accordance with the change procedure(s) described in the ERCOT Protocols, in effect at the time of the performance or non-performance of an action, shall govern with respect to that action.

  • Step therapy protocol means a protocol or program that establishes the specific

  • Protocol means, in respect of any category of object and associated rights to which this Convention applies, the Protocol in respect of that category of object and associated rights;

  • Interconnection Feasibility Study means either a Generation Interconnection Feasibility Study or Transmission Interconnection Feasibility Study.

  • HEPA filter means a high efficiency particulate absolute air filter capable of trapping and retaining 99.97 percent of fibers greater than 0.3 micrometers in mass median aerodynamic diameter equivalent.

  • Generation Interconnection Feasibility Study means a study conducted by the Transmission Provider (in coordination with the affected Transmission Owner(s)) in accordance with Tariff, Part IV, section 36.2.

  • cGMP means current Good Manufacturing Practices as specified in the United States Code of Federal Regulations, ICH Guideline Q7A, or equivalent laws, rules, or regulations of an applicable Regulatory Authority at the time of manufacture.

  • MSAA Indicator Technical Specifications document means, as the context requires, either or both of the document entitled “Multi-Sector Service Accountability Agreement (MSAA) 2019-20 Indicator Technical Specifications November 5, 2018 Version 1.3” and the document entitled “Multi-Sector Service Accountability Agreement (MSAA) 2019-20 Target and Corridor-Setting Guidelines” as they may be amended or replaced from time to time;

  • Backflow prevention device means a safety device used to prevent pollution or contamination of the water supply due to the reverse flow of water from the irrigation system.

  • Manufacturing Process means any process for—

  • GMP means the amount proposed by Contractor and accepted by Owner as the maximum cost to Owner for construction of the Project in accordance with this Agreement. The GMP includes Contractor’s Construction Phase Fee, the General Conditions Cost, the Cost of the Work, and Contractor’s Contingency amount.

  • Drug test means a test designed to detect the illegal use of a controlled substance.

  • Detailed manufacturing or process data means technical data that describe the steps, sequences, and conditions of manufacturing, processing or assembly used by the manufacturer to produce an item or component or to perform a process.

  • Diagnostic clinical procedures manual means a collection of written procedures that describes each method (and other instructions and precautions) by which the licensee performs diagnostic clinical procedures; where each diagnostic clinical procedure has been approved by the authorized user and includes the radiopharmaceutical, dosage, and route of administration.

  • Commercial applicator means any person, unless exempted in I(4) hereunder, whether or not the person is a private applicator with respect to some uses, who:

  • health and safety specification means a site, activity or project specific document prepared by the client pertaining to all health and safety requirements related to construction work;