Common use of Wrenches Clause in Contracts

Wrenches. 050" - 3/8" Fractional • 2mm - 7mm Metric Blade Type • Stubby • Pocket Screwdriver • 1/4" x 6" • 1/4" x 9" • 3/8" x 9" • 3/8" x 16" • Offset ▇▇▇▇▇▇▇▇ • #2 Stubby • #1 Tip • #2 Tip • #3 Tip • Offset T-8, T-10, T-20, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇ • Slip Joint 6" • Slip Joint 6" • Needle Nose 6" • Diagonal Cutter 7" • Channel Locks 12" (water pump) • Duck ▇▇▇▇ Pliers 7 3/4" (ex. snap-on # 61ACP) • Vise Grip Pliers 10" (10WR) • Internal Retaining Ring Pliers • External Retaining Ring Pliers • Snap Ring Pliers (ex. Snap-On SRP2 style) • ▇▇▇▇ ▇▇" ▇▇▇▇ ▇▇▇▇▇▇▇ • Round 8" - 10" • Three Cornered • 16oz Ball Peen • 160z Soft Faced Dead Blow • Hand Drilling 3 to 4 lb. • Center Punch • Pin Punch - 1/8", 3/16", 1/4", 5/16" • Taper ▇▇▇▇▇ ▇/▇", ▇/▇", ▇/▇" • ▇▇▇▇▇ ▇▇▇▇▇ - ▇/▇" • Cape Chisel - 5/16" • Cold Chisel - 3/8" - 3/4" • Rolling Head 16" • Straight 16" • Brake Spring Pliers • Spring Hold Down Tool • Digital Multi meter • 12 volt test light or LED circuit Tester • Remote Starter Switch • Insulation piercing test probes (ex EZ Hooks) • Wire ▇▇▇▇▇▇▇▇/▇▇▇▇▇▇ ▇▇▇▇▇▇ ▇" (▇▇ ▇▇▇▇-▇▇ ▇▇▇▇▇▇) • Pocket Flash Light • Pocket Knife • "O" Ring Pick Set • A/C, fuel line disconnect set • Inspection Mirror • Spark Plug Feeler Gauge (gap tool) • Feeler Gauge (Blade type) • Flexible Pick Up Tool (magnetic and claw type) • Tape Measure 12" • Hack Saw • Tubing Cutter • Gasket/Carbon Scraper (putty knife) • Air Blow Gun (Meeting OSHA requirements) • Roll Away with Key Lock • In addition to the above list, it is recommended that the employee retain the following tools. The company agrees to assist in the purchase of these tools. • 3/8" Drive Air Ratchet

Wrenches. 050" - 3/8" Fractional • 2mm - 7mm Metric Blade Type • Stubby • Pocket Screwdriver • 1/4" x 6" • 1/4" x 9" • 3/8" x 9" • 3/8" x 16" • Offset ▇▇▇▇▇▇▇▇ • #2 Stubby • #1 Tip • #2 Tip • #3 Tip • Offset T-8, T-10, T-20, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇, ▇-▇▇ • Slip Joint 6" • Slip Joint 6" • Needle Nose 6" • Diagonal Cutter 7" • Channel Locks 12" (water pump) • Duck ▇▇▇▇ Pliers 7 3/4" (ex. snap-on # 61ACP) • Vise Grip Pliers 10" (10WR) Snap/Retaining Ring Pliers • Internal Retaining Ring Pliers • External Retaining Ring Pliers • Snap Ring Pliers (ex. Snap-On SRP2 style) • ▇▇▇▇ ▇▇" ▇▇▇▇ ▇▇▇▇▇▇▇ • Round 8" - 10" • Three Cornered • 16oz Ball Peen • 160z Soft Faced Dead Blow • Hand Drilling 3 to 4 lb. • Center Punch • Pin Punch - 1/8", 3/16", 1/4", 5/16" • Taper ▇▇▇▇▇ ▇/▇", ▇/▇", ▇/▇" • ▇▇▇▇▇ ▇▇▇▇▇ - ▇/▇" • Cape Chisel - 5/16" • Cold Chisel - 3/8" - 3/4" • Rolling Head 16" • Straight 16" • Brake Spring Pliers • Spring Hold Down Tool • Digital Multi meter • 12 volt test light or LED circuit Tester • Remote Starter Switch • Insulation piercing test probes (ex EZ Hooks) • Wire ▇▇▇▇▇▇▇▇/▇▇▇▇▇▇ ▇▇▇▇▇▇ ▇" (▇▇ ▇▇▇▇-▇▇ ▇▇▇▇▇▇) • Pocket Flash Light • Pocket Knife • "O" Ring Pick Set • A/C, fuel line disconnect set • Inspection Mirror • Spark Plug Feeler Gauge (gap tool) • Feeler Gauge (Blade type) • Flexible Pick Up Tool (magnetic and claw type) • Tape Measure 12" • Hack Saw • Tubing Cutter • Gasket/Carbon Scraper (putty knife) • Air Blow Gun (Meeting OSHA requirements) • Roll Away with Key Lock • In addition to the above list, it is recommended that the employee retain the following tools. The company agrees to assist in the purchase of these tools. • 3/8" Drive Air RatchetRatchet • 1/2" Drive Air Impact Gun • Crankshaft Pulley Puller • Cylinder leakage tester • Pry Bar Screwdriver style 30" or larger • Hand Operated Vacuum Pump • Compression Gauge • Radiator Pressure Tester • Feeler Gauge (Go-No-Go, blade type) • Door Panel Removal Tool