Marking of Licensed Products To the extent commercially feasible and consistent with prevailing business practices, Company shall xxxx, and shall cause its Affiliates and Sublicensees to xxxx, all Licensed Products that are manufactured or sold under this Agreement with the number of each issued patent under the Patent Rights that applies to such Licensed Product.
Licensed Products Lessee will obtain no title to Licensed Products which will at all times remain the property of the owner of the Licensed Products. A license from the owner may be required and it is Lessee's responsibility to obtain any required license before the use of the Licensed Products. Lessee agrees to treat the Licensed Products as confidential information of the owner, to observe all copyright restrictions, and not to reproduce or sell the Licensed Products.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.
Licensed Product “Licensed Product” shall mean any article, composition, apparatus, substance, chemical material, method, process or service whose manufacture, use, or sale is covered or claimed by a Valid Claim within the Patent Rights. For clarity, a “Licensed Product” shall not include other product or material that (a) is used in combination with Licensed Product, and (b) does not constitute an article, composition, apparatus, substance, chemical material, method, process or service whose manufacture, use, or sale is covered or claimed by a Valid Claim within the Patent Rights.
Supply of Product 3.1 In accordance with the terms of this Agreement, GENSIA SICOR (through SICOR) shall supply all of PURCHASER'S ordered requirements for Product in bulk form for use by PURCHASER in the Territories in accordance with the provisions of this Agreement. The right and license of PURCHASER to obtain, use and distribute Product (including, without limitation, the right to make or have made Product) from GENSIA SICOR and SICOR shall be (i) non-exclusive in the Non-exclusive Territory, and (ii exclusive in the Exclusive Territory; provided, however, that the rights and licenses set forth in clause (ii) above shall be co-exclusive in each jurisdiction in which GENSIA SICOR (or ALCO or SICOR, as the case may be) has binding written agreements, or binding written commitments that will lead to binding written agreements, to sell Product on the Restatement Date (which is limited to only those [ * ] and the [ * ] with whom GENSIA SICOR has commitments that are in existence on the Restatement Date), but only with respect to such third parties and only until the earlier of expiration or termination of such agreements; and provided, further that GENSIA SICOR shall use all diligent efforts (without any obligation to violate or alter the terms of such agreements existing on the Restatement Date) to provide PURCHASER with exclusive rights and licenses to sell the Products in the Territory as soon as possible. All Product hereunder shall be manufactured at SICOR's GMP facilities at Rho, Italy, the facility identified in Exhibit 9 hereto, the Santxx Xxxility and additional (as necessary and as provided in Section 6 below) GMP qualified facilities that are approved in advance by PURCHASER (which approval will not be unreasonably withheld). In addition, all Product shall be manufactured (A) in accordance with drug substance manufacturing and quality control procedures existing on the Effective Date, which drug substance manufacturing and quality control procedures have been included in manufacturer's Abbreviated Antibiotic Drug Application ("AADA") submitted to the FDA in 1996, and that will be submitted to other Regulatory Authorities in the Territory (which AADA shall include at least the elements set forth in the Drug Master File) in accordance with U.S. FDA current Good Manufacturing Practices, and (B) to the Q/C Specifications. GENSIA SICOR shall cause SICOR to use its diligent efforts to [ * ] in order to produce and supply all Product ordered by Purchaser hereunder and to meet the Product [ * ] that will be set forth in Schedule 1 hereto within [ * ] after the Restatement Date. In addition, GENSIA SICOR agrees to the following (and GENSIA SICOR agrees to cause SICOR to undertake):
Commercialization Intrexon shall have the right to develop and Commercialize the Reverted Products itself or with one or more Third Parties, and shall have the right, without obligation to Fibrocell, to take any such actions in connection with such activities as Intrexon (or its designee), at its discretion, deems appropriate.
Supply of Products During the term of this Agreement and any extension hereof, the Seller shall sell and supply the products as set out in Schedule 1 hereto (“Products”) to SiPM and SiPM shall buy from the Seller such Products on a non-exclusive basis. The specifications of the Products are set out in Schedule 2 hereto. SUPPLY AGREEMENT - SiPM A Supply Agreement is a document between two parties, a Supplier and a Purchaser. The Supplier can be an individual or business and is the party that " supplies," or sells, the goods to the Purchaser. The Purchaser can also be an individual or a business and is the party that purchases for its use the goods that the Supplier provides.
Supply of Materials The following materials will be supplied by the department Name of Materials Rate. Place of delivery 1.
Commercialization License Subject to the terms of this Agreement, including without limitation Section 2.2 and Theravance's Co-Promotion rights in Section 5.3.2, Theravance hereby grants to GSK, and GSK accepts, an exclusive license under the Theravance Patents and Theravance Know-How to make, have made, use, sell, offer for sale and import Alliance Products in the Territory.
