Common use of Specific Requirements Clause in Contracts

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) All 46, 47, 48, 49, 50, 51A, 51B, and 51C which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

AutoNDA by SimpleDocs

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Lang Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C live trees meeting the attached designation description which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange or pink tracer , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by shall furnish flag personnel meeting the Forest Service prior to the start requirements of Chapter 6E of the MUTCD and advance warning signs when operating within the roadway of Hwy 224. Purchaser shall receive approval from ODOT for Purchaser’s safety measures and traffic control plans before commencement of operations. Purchaser Purchaser/Contractor and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) All 46, 47, 48, 49, 50, 51A, 51B, and 51C which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser Purchaser/Contractor and Forest Service agree to the above stated requirements of the Traffic Control Plan: . Name Name Title Title Date Date Sale Name: Spud Thin CT2.3C2.35# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010OPTION 1) (06/2008) All 46, 47, 48, 49, 50, 51A, 51B, and 51C live trees meeting the attached designation by description which meet the minimum tree diameter stated in AT2 A2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37B2.37. Leave trees, Marked with orange or pink tracer paint , or identified by by, the description in the attached table , are not to be cut, unless designated by the Forest Service. CT4.211 C3.34 - DOWNPAYMENT EMERGENCY RATE REDETERMINATION (06/200706/2022) The downpayment amount shown Forest Service shall redetermine rates for each species if, upon Contractor's application, Forest Service determines that, because of changes in AT15 may the timber market since the award date or the last rate redetermination under this provision, the Producer Price Index identified in A20 has declined by 25 percent or more. Rates shall be redetermined under B3.3 and for species where the rates declined, shall be considered established under B3.1 for timber Scaled after Contractor's application. Increases in species rates will not be applied toward any other payment required under considered. This provision shall not apply during the provisions period of this contracta Contract Term Extension. C3.47# - ABNORMAL DELAY (05/2005) Unless otherwise agreed, except damages determined felled timber meeting Utilization Standards shall be removed by Contractor pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, B2.2 and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised presented for Scaling within the time period indicated in the following removal schedule. The number of days shown are consecutive calendar days. Failure to remove and applied in accordance with 36 CFR 223.49(f)present such timber for Scaling within the required time limits will be considered abnormal delay, subject to B3.47. Page 141a Sale See attached removal schedule. Contract Name: Spud Thin UDESCRIPTION Falls STEW IRTC Page 145 Contract 2400-13,(10/19) DESCRIPTION PURSUANT TO CT2.35C2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/201006/2008) DESIGNATION BY DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *(DxD) Subdivision Designated Species Species/1 (Live) Designated Tree Diameter Limit DxD Spacing/2 (DSHfeet) DSH Cutting Limits3/ (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Within Unit Created Gap 1/4 Acre/4 Within Unit Created Skip 1/4 Acre/5 Very Heavy Thin Patches LTM 1 Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation 15 8 to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non24 4 - 1 2 Xxxxxxx-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height fir 17 8 to outside bark xxxxx height (face of tree). CT4.212 24 2 3 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:3 Xxxxxxx-fir 16 8 to 24 - 4 - 4 Xxxxxxx-fir 18 8 to 24 - 4 1 5 Xxxxxxx-fir 15 8 to 24 3 9 - 6 Xxxxxxx-fir 17 8 to 24 3 3 -

Appears in 1 contract

Samples: www.fs.usda.gov

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Sugar Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C live trees meeting the attached designation description which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange or pink tracer, or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Purchaser Title Forest Service Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. B & B SBA CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C live trees as described in the table on following page which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange or white paint (LTM) , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Signing required if there are wait periods associated with operations on Forest Roads 2400000 and 6020000. Wait periods shall be limited to 30 minutes Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Smoky Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C trees meeting the attached designation description which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange pink , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

AutoNDA by SimpleDocs

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. Xxxx Xxxx CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C live trees meeting the attached designation description which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange or pink tracer paint , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Signing required if there are wait periods associated with operations on Forest Road 2500000, 3211000 and 9000000. Wait periods shall be limited to 30 minutes. Signing required if there are closures associated with operations on Forest Roads 2560000 and 2573000. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. Xxxxx Xxxx CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) Page 141 All 46, 47, 48, 49, 50, 51A, 51B, and 51C trees meeting the attached designation description which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; ⮚ Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. ⮚ Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. ⮚ Non-designated species within the diameter limits shall not be considered in spacing ⮚ Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. ⮚ Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. ⮚ No Cut Area: Do not cut any tree, except those in skyline yarding corridor. ⮚ Xxxxx height is measured at 6.0 inches on high side of tree. ⮚ Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Specific Requirements. Signs in Part I will be installed and maintained by Purchaser at locations indicated by the Forest Service prior to the start of the operations. Purchaser and Forest Service agree to the above stated requirements of the Traffic Control Plan: Name Name Title Title Date Date Sale Name: Spud Thin CT2.3# - RESERVE TREES (04/2004) Page 141 Notwithstanding the designations for cutting under BT2.31, BT2.32, BT2.33, or BT2.34, live or dead genetic reserve trees or groups of reserve trees within such cutting units or clearings shall be left uncut. Such Reserve trees are identified by band of orange paint and yellow metal tag and shall be protected in accordance with CT6.32#. Units with reserve trees are shown on the Sale Area Map. CT2.35# (OPTION 1) - INDIVIDUAL TREE DESIGNATION (06/2010) All 46, 47, 48, 49, 50, 51A, 51B, and 51C which meet the minimum tree diameter stated in AT2 are designated for cutting. Additional timber to be cut, if any, will be designated for cutting in accordance with BT2.37. Leave trees, Marked with orange , or identified by the description in the attached table are not to be cut, unless designated by the Forest Service. CT4.211 - DOWNPAYMENT (06/2007) The downpayment amount shown in AT15 may not be applied toward any other payment required under the provisions of this contract, except damages determined pursuant to BT9.4, transferred to other timber sales, or refunded until (a) stumpage value representing 25 percent of the total bid value of the timber sale is shown on Timber Sale Account to have been cut, removed, and paid for, or (b) the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpayment, or (c) if 36 CFR 223.49(e) is applicable, the estimated value remaining to be cut and removed, as shown on Timber Sale Account, is equal to or less than the amount of the downpay-ment. For lump sum timber sales, the downpayment may be applied to payment for release of the single payment unit. If Forest Service makes a determination that this contract should not have been included under in- creased downpayment requirements (36 CFR 223.49(e)), the downpayment shall be revised and applied in accordance with 36 CFR 223.49(f). Page 141a Sale Name: Spud Thin UDESCRIPTION PURSUANT TO CT2.35# (Option 1) – INDIVIDUAL TREE DESIGNATION (06/2010) DESIGNATION DESCRIPTION All Payment Units External boundaries are designated on the ground with boundary tags labeled “Spud” and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. No Cut Area is designated on the ground with red “Special Treatment Area” tags and orange paint through the tag and on the xxxxx. Boundary trees are not Included Timber and shall not be cut. These trees shall be considered in spacing. Payment Unit *Designated Species (Live) Designated Tree Diameter Limit (DSH) (min–max inches) DxD Spacing(ft) *Number & Size of Gaps 48 DF, H 7.0 – 30.0 17 0 49 DF 7.0 – 27.0 16 30 - 1/8 acre H 16 50 DF 7.0 – 27.0 23 11 - 1/5 acre 51A DF 7.0 – 40.0 21 0 51B DF, H 10.0 – 40.0 20 0 51C DF, H 10.0 – 40.0 25 0 *Designated Species: DF = Xxxxxxx-fir; H = western hemlock *Size of Gaps: 1/8 acre = radius of 42 feet; 1/5 acre = radius of 53 feet; Cut all Designated Species trees, if the tree is within the DxD spacing of a Designated Species tree that has a larger xxxxx diameter. Leave the tree with the larger diameter. Units 47 and 49: There are two cut species, Xxxxxxx-fir (DF) and hemlock(H) where each species is cut in relation to others of the same species. Largest diameter DF cuts only other DF, and largest diameter H cuts only other H. Trees less than the minimum xxxxx diameter and greater than the maximum xxxxx diameter are not Included Timber and shall not be cut. These trees shall not be considered in spacing. Non-designated species within the diameter limits shall not be considered in spacing Gaps: Center tree designated with a double band of pink paint. From the center tree, cut all Designated Species trees within the diameter limits and radius specified above. Do not cut trees designated with a single band of orange paint. Single Leave Trees: Do not cut trees designated with a single band of orange paint. Designated in general thinning area and an additional tree designated in gap. These trees shall not be considered in spacing. No Cut Area: Do not cut any tree, except those in skyline yarding corridor. Xxxxx height is measured at 6.0 inches on high side of tree. Distances are measured slope distance, outside bark xxxxx height to outside bark xxxxx height (face of tree). CT4.212 - TEMPORARY REDUCTION OF DOWNPAYMENT (08/2009) Notwithstanding BT4.211 or CT4.211, upon the Purchaser's written request Forest Service may temporarily reduce the downpayment when Purchaser's scheduled operations are delayed or interrupted for 30 or more consecutive days, or the contract term is extended for 30 or more consecutive days for any of the following reasons:

Appears in 1 contract

Samples: Service Timber Sale Contract

Time is Money Join Law Insider Premium to draft better contracts faster.