Schedule 2: NPCC Governance and Accountability Schedule. The Chief Constables’ Council and Policing Bodies The Chief Constables’ Council (representing Chief Officers) and Policing Bodies may jointly agree any variation to Schedule 2;
Schedule 2: NPCC Governance and Accountability Schedule Sample Clauses
Related to Schedule 2: NPCC Governance and Accountability Schedule
Wall Street Transparency and Accountability Act of 2010 The parties hereby agree that none of (i) Section 739 of the WSTAA, (ii) any similar legal certainty provision included in any legislation enacted, or rule or regulation promulgated, on or after the Trade Date, (iii) the enactment of the WSTAA or any regulation under the WSTAA, (iv) any requirement under the WSTAA or (v) any amendment made by the WSTAA shall limit or otherwise impair either party’s right to terminate, renegotiate, modify, amend or supplement this Confirmation or the Agreement, as applicable, arising from a termination event, force majeure, illegality, increased cost, regulatory change or similar event under this Confirmation, the Equity Definitions or the Agreement (including, but not limited to, any right arising from any Acceleration Event).
Service Accountability Agreements The HSP acknowledges that if the LHIN and the HSP enter into negotiations for a subsequent service accountability agreement, subsequent funding may be interrupted if the next service accountability agreement is not executed on or before the expiration date of this Agreement.
A Service Accountability Agreement This Agreement is a service accountability agreement for the purposes of section 20(1) of LHSIA.
NMHS Governance, Safety and Quality Requirements 3.1 Participates in the maintenance of a safe work environment.
Wall Street Transparency and Accountability Act In connection with Section 739 of the Wall Street Transparency and Accountability Act of 2010 (“WSTAA”), the parties hereby agree that neither the enactment of WSTAA or any regulation under the WSTAA, nor any requirement under WSTAA or an amendment made by WSTAA, shall limit or otherwise impair either party’s otherwise applicable rights to terminate, renegotiate, modify, amend or supplement this Confirmation or the Agreement, as applicable, arising from a termination event, force majeure, illegality, increased costs, regulatory change or similar event under this Confirmation, the Equity Definitions incorporated herein, or the Agreement (including, but not limited to, rights arising from Change in Law, Hedging Disruption, Increased Cost of Hedging, an Excess Ownership Position, or Illegality (as defined in the Agreement)).
Federal Funding Accountability and Transparency Act (FFATA Subrecipient shall comply with the requirements of 2 CFR part 25 Universal Identifier and System for Award Management (XXX). Subrecipient must have an active registration in XXX, xxxxx://xxx.xxx.gov/XXX/ in accordance with 2 CFR part 25, appendix A, and must have a Data Universal Numbering System (DUNS) number xxxxx://xxxxxx.xxx.xxx/webform/ Subrecipient must also comply with provisions of the Federal Funding Accountability and Transparency Act, which includes requirements on executive compensation, 2 CFR part 170 Reporting Subaward and Executive Compensation Information.
EMHS Governance, Safety and Quality Requirements 4.1 Participates in the maintenance of a safe work environment.
SMHS Governance, Safety and Quality Requirements 4.1 Participates in the maintenance of a safe work environment.
Insurance and Fingerprint Requirements Information Insurance If applicable and your staff will be on TIPS member premises for delivery, training or installation etc. and/or with an automobile, you must carry automobile insurance as required by law. You may be asked to provide proof of insurance. Fingerprint It is possible that a vendor may be subject to Chapter 22 of the Texas Education Code. The Texas Education Code, Chapter 22, Section 22.0834. Statutory language may be found at: xxxx://xxx.xxxxxxxx.xxxxx.xxxxx.xx.xx/ If the vendor has staff that meet both of these criterion: (1) will have continuing duties related to the contracted services; and (2) has or will have direct contact with students Then you have ”covered” employees for purposes of completing the attached form. TIPS recommends all vendors consult their legal counsel for guidance in compliance with this law. If you have questions on how to comply, see below. If you have questions on compliance with this code section, contact the Texas Department of Public Safety Non-Criminal Justice Unit, Access and Dissemination Bureau, FAST-FACT at XXXX@xxxxx.xxxxx.xx.xx and you should send an email identifying you as a contractor to a Texas Independent School District or ESC Region 8 and TIPS. Texas DPS phone number is (000) 000-0000. See form in the next attribute to complete entitled: Texas Education Code Chapter 22 Contractor Certification for Contractor Employees
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
