Safety and the Environment. 15: Except where otherwise agreed by the Company the Boat Owner shall at all times maintain valid Boat Safety Scheme certification for the Vessel if that Vessel is moored or navigates above Hall Bridge on the Navigation. The Boat Owner agrees to pay an additional administration charge of £50 for each quarter in which current Boat Safety Scheme certification is not held for a period of 30 days or more for any boat that moors or navigates (for however short a period) above Hall Bridge.
Safety and the Environment. In the event of any spillage (which for the purpose of this Clause shall mean any leakage, escape, or overflow of the Marine Fuels) causing or likely to cause pollution occurring at any stage of the bunkering operation, the Buyer or the Seller shall jointly, and regardless as to whether the Buyer or the Seller is responsible, immediately take such action as is necessary to effect clean up and which shall always be conducted in accordance with such local laws and regulations which may compulsorily apply.
Safety and the Environment a. In performing their obligations under this agreement, their respective operating licences and other legislative and regulatory requirements, theBWSP and Service Provider are committed to the safety of employees, contractors and members of the public and will place safety first when performing their respective obligations.
Safety and the Environment. All employees covered by this agreement shall have a commitment to working safely and protecting the environment, and shall be pro-active in identifying and reducing potential hazards and environmental dangers in the workplace.
Safety and the Environment. Without limiting its other obligations under the Contract or otherwise at law, when carrying out the Services, the Service Provider must:
Safety and the Environment. We also desire to deliver services in a manner that safeguards our employees, our customers, and the environment. Xxxxxxxx employs a full−time safety officer for training, inspections, and consultation to ensure that the safety of our employees and customers is protected. These work−safe practices go hand−in−hand with work processes that ensure that no environmental degradation occurs in either our sites or those of our customers. Commissioning and Measurement/Verification (M&V): Thielsch/RISE recognizes the importance of commissioning to ensure the project is implemented and functions as intended. While measurement and verification is related to the performance of the implemented work, commissioning goes beyond to ensure the correct equipment is provided, and it is able to provide the desired operational result (airflow, temperature, on−off, modulation, etc). It is important to ensure not only the specific ECM being implemented is properly commissioned, but the related equipment is also addressed such that the entire system is confirmed to be functioning as anticipated. Along with the M&V plan, Xxxxxxxx/RISE will provide a proposed commissioning plan as part of the audit process. This plan serves as the framework for commissioning activities and will be further enhanced during the final design process to add additional specific activities informed from such final design. Thielsch/RISE bases its project specific verification plans on the International Performance Measurement & Verification Protocol (IPMVP) and will conform to the FEMP standard, where applicable. These established and well−known documents provide the framework under which an appropriate verification plan can be developed and have been the basis for Thielsch/RISE personnel crafting hundreds of previous verification plans. While some specifics of the IPMVP and FEMP standard have evolved since our personnel starting crafting verification plans in the early 1990s, the overall framework has remained the same with improvements to the specifics of the general approaches to ensure confidence in project savings. IPMVP Option Description Summary A Retrofit−isolation: Key Parameter Measurement Engineering calculation based on baseline and reporting period energy usage; short−term or continuous measurements of key parameter(s) with the remaining variables being estimated. B Retrofit−isolation: All Parameter Measurement Short−term or continuous measurements of baseline and reporting period energy usage,...
Safety and the Environment. Without limiting its other obligations under this Contract or otherwise at law (including under the WHS Law), when carrying out the Services, the Consultant must:
Safety and the Environment. 9.1 ESS shall, at all times maintain safe working conditions and comply with all relevant occupational health and safety and environmental laws and regulations.
Safety and the Environment. 9.1 Lessor shall execute the construction safely and so as to protect persons and property. The Lessor shall be responsible for securing insurance for the General Contractor, subcontractors and property insurance for the expansion facility. The Lessee shall be responsible for insurance for its employees.
Safety and the Environment. 1. The Hardware must be adequately packed and must be marked in accordance with statutory instructions, decrees and any other additional regulations of the Principal, to ensure that they reach their destination in good condition. All packaging and/or packaging material will be taken back by the Supplier upon delivery or, insofar as applicable, upon Installation, or insofar as otherwise agreed in Appendix V – Additional Agreements.
