Rotor balance vibration limits Sample Clauses

Rotor balance vibration limits a) The rotor must be balanced at 3000rpm to the following acceptance criteria:  Cold – Shaft relative(run out compensated) 48µm pk-pk at 1F and less than 100µmpk-p through the speed range including over-speed.  Hot – Shaft relative(run out compensated) 60µm pk-pk at 1F. The acceptable shaft relative vibration limits of the rotor during rundown in the hot condition must be less than 260µmpk-pk.
AutoNDA by SimpleDocs

Related to Rotor balance vibration limits

  • Reallocation to a Class with a Lower Salary Range Maximum 1. If the employee meets the skills and abilities requirements of the position and chooses to remain in the reallocated position, the employee retains existing appointment status and has the right to be placed on the Employer’s internal layoff list for the classification occupied prior to the reallocation.

  • Minimum Balance Merchant agrees to maintain a minimum balance of funds in the Settlement Account as Bank may specify to Merchant in writing from time to time.

  • Position Limits We may require you to limit the number of open positions which you may have with us at any time and we may in our sole discretion close out any one or more Transactions in order to ensure that such position limits are maintained.

  • Maximum Contribution The total amount you may contribute to an IRA for any taxable year cannot exceed the lesser of 100 percent of your compensation or $6,000 for 2019 and 2020, with possible cost- of-living adjustments each year thereafter. If you also maintain a Xxxx XXX (i.e., an IRA subject to the limits of Internal Revenue Code Section (IRC Sec.) 408A), the maximum contribution to your Traditional IRAs is reduced by any contributions you make to your Xxxx IRAs. Your total annual contribution to all Traditional IRAs and Xxxx IRAs cannot exceed the lesser of the dollar amounts described above or 100 percent of your compensation.

  • Contribution Formula - Basic Life Coverage For employee basic life coverage and accidental death and dismemberment coverage, the Employer contributes one-hundred (100) percent of the cost.

  • Dollar Limits Per Service Agreement Cost to diagnose, repair and/or replace - Geothermal and water source systems $1,500 Water cooled air conditioners, high velocity and hydronic systems $1,500 Concrete encased or concealed ductwork $500 Refrigerant lines $500 Appliances l Standard/Seller Coverage S Supreme Coverage l S Appliance color matchSM l S Built-in microwave l S Dishwasher l S Garbage disposal l S Range, oven, cooktop and vent hood l S Refrigerator - INCLUDING ICE MAKER! S Washer and dryer S Range, oven, cooktop, hood: handles, hinges, clocks, rotisseries, racks, knobs and dials, interior lining, glass/ceramic cooktops, self cleaning mechanisms and latch assemblies S Kitchen Refrigerator: handles, hinges, ice crusher, beverage dispenser and respective equipment S Built-in microwave: handles, hinges, interior lining, clocks and shelves, turntable platforms and rollers S Dishwasher: handles, hinges, racks, baskets, rollers, tub and interior lining, springs, latch assemblies and soap dispensers S Permits up to $250 per Service Agreement S Modifications up to $250 per Service Agreement S Haul away/disposal fees S Items under manufacturer’s warranty Excluded Items: ✖ Appliances not located in the primary kitchen (except washer and dryer) and duplicate appliances, unless additional refrigerator option(s) are purchased. ✖ Meat probe assemblies, door glass, sensi-heat burners will only be replaced with standard burners for range, oven, cooktop. ✖ Multimedia center including technology convenience items like LCD screens, Wi-Fi and cameras. ✖ Racks, hinges, shelves, interior thermal shells, food spoilage and freezers which are not an integral part of the kitchen refrigerator. ✖ Door glass, portable or counter top units, trim kits, meat probe assemblies, rotisseries for built-in microwave. ✖ Damage to clothing, plastic mini-tub, soap dispensers, filter screens, knobs, dials, hinges and lint screen for washer or dryer. ✖ Gas supply line to stove.

  • Reallocation to a Class with a Higher Salary Range Maximum Upon appointment to the higher class, the employee’s base salary will be increased to a step of the range for the new class that is nearest to five percent (5.0%) higher than the amount of the pre-promotional step, or to the entry step of the new range, whichever is higher.

  • Minimum Balance Requirements To be a member and maintain Accounts with Us You must purchase 1 share in the Credit Union. The par value of a share in this Credit Union is $5.00. If the balance in Your primary share Account drops below 1 share ($5.00), at any time, We may, at Our option, close Your Account. Nonsufficient Funds Returns. Any share draft or pre-authorized transfer, or transaction made through the use of a debit card, or other electronic means, as is applicable (including any in-person transaction), that is presented to Us for payment on Your Account when Your Account lacks sufficient collected funds to pay any such item may, at Our option, be returned for nonsufficient funds or We may honor any such item and charge You a fee for doing so. Overdraft Balance Calculation. When processing transactions that debit or credit Your Account, We start each Business Day with Your final Account balance from the preceding Business Day. The final balance takes into account all of the debit and credit transactions that were settled that Business Day pursuant to Our Funds Availability Policy, as well as any other debits or credits to Your Account that were finally settled that day, as described above in the "Deposit of Items" and "Collection and Processing of Items" sections of the Account Agreement. This starting balance at the beginning of a Business Day (the preceding Business Day's final balance) is sometimes referred to as Your "actual balance." As credits and debits to Your Account are received by Us, We add them to and subtract them from Your actual balance. Examples of credits include, but are not limited to, electronic direct deposits, check deposits that have been fully and finally collected, ACH credits that have settled that day, and cash deposits made to one of Our tellers. Examples of debits include, but are not limited to, checks drawn on Your Account that are presented to Us for payment, electronic fund transfer (EFT) debit transactions (such as preauthorized payments and settled EFT debits), memo-posted EFT debits (EFT debits that We have authorized but which have not been settled), and Credit Union fees and charges. The result of this calculation at any given point in time is called Your "available balance." For the purpose of determining whether an overdraft has occurred, We use Your available balance. First, We add all of the settled credit transactions to the beginning actual balance. Then, We subtract all of the debit transactions that settled that day. We also subtract all of the pending debit transactions. This determines the available balance for overdraft purposes. Each debit transaction that We process when Your Account has a negative available balance is an overdraft, subject to an overdraft charge. Subject to applicable law, You are responsible for paying any overdraft fees and charges assessed in connection with Our payment of an overdraft, as well as any NSF fees charged to Your Account when We dishonor and return an item for non- sufficient funds. It is Your responsibility to know Your Account balance, and if You have any questions You should contact a Credit Union representative.

  • Transaction Limits 5.1 You must not use or attempt to use your Citibank ATM/Debit Card to effect any Card Transaction or obtain any Cash Withdrawal or Cash Advance if:

  • Minimum Interest Coverage Ratio The Borrowers shall not permit the Interest Coverage Ratio, calculated as of the end of each fiscal quarter for the four fiscal quarters then ended, to be less than 3.50 to 1.00.

Time is Money Join Law Insider Premium to draft better contracts faster.