Common use of REGISTRATION MARKS Clause in Contracts

REGISTRATION MARKS. The original Silhouette, Silhouette SD, CAMEO, and Portrait models have an optic scanner for reading marks that can be printed by Silhouette Studio®. These marks are called Registration Marks. These marks will print around the border of your workspace and will be read by the Silhouette’s optic scanner prior to cutting so that the Silhouette can triangulate according to where these marks are located and know exactly where the cut lines are defined around your printed images. Registration marks are only used when printing images for the purpose of performing print & cut jobs. To access these marks, click on the Registration Marks icon. You may enable the registration marks by clicking on the Show Reg Marks check box. If desired according to the job being performed, these marks can be adjusted. Please note that while you may make the marks smaller, if the Silhouette fails to locate these marks, you may need to adjust the registration ▇▇▇▇ size to ensure the optic scanner is able to successfully locate these marks. You will note that the marks have a ▇▇▇▇ ▇▇▇▇ fill around them. This ▇▇▇▇ ▇▇▇▇ fill indicates that print information cannot be contained in this area in order for the optic scanner to operate properly.

REGISTRATION MARKS. The original Silhouette, Silhouette SD, CAMEOCameo, Portrait, and Portrait Curio models have an optic scanner for reading marks that can be printed by Silhouette Studio®. These marks are called Registration Marksregistration marks. These marks will print around the border of your workspace and will be read by the Silhouette’s optic scanner prior to cutting so that the Silhouette can triangulate according to where these marks are located and know exactly where the cut lines are defined around your printed images. Registration marks are only used when printing images for the purpose of performing print Print & cut Cut jobs. To access these marks, click on the Registration Marks iconicon in the Page panel. You may enable the registration marks by clicking on selecting Type 1 or Type 2 under the Show Reg Marks check boxRegistration Mark icon. If desired according to the job being performed, these marks can be adjusted. Please note that while you may make the marks smaller, if the Silhouette fails to locate these marks, you may need to adjust the registration ▇▇▇▇ mark size to ensure the optic scanner is able to successfully locate these marks. You will note that the marks have a ▇▇▇▇ ▇▇▇▇ fill around them. This ▇▇▇▇ ▇▇▇▇ fill indicates that print information cannot be contained in this area in order for the optic scanner to operate properly.

REGISTRATION MARKS. The original Silhouette, Silhouette SD, CAMEO, and Portrait models Silhouette SD have an optic scanner for reading marks that can be printed by Silhouette Studio®. These marks are called Registration Marks. These marks will print around the border of your workspace and will be read by the Silhouette’s optic scanner prior to cutting so that the Silhouette can triangulate according to where these marks are located and know exactly where the cut lines are defined around your printed images. Registration marks are only used when printing images for the purpose of performing print Print & cut Cut jobs. To access these marks, click on the Registration Marks icon. You may enable the registration marks by clicking on the Show Reg Marks check box. If desired according to the job being performed, these marks can be adjusted. Please note that while you may make the marks smaller, if the Silhouette fails to locate these marks, you may need to adjust the registration ▇▇▇▇ mark size to ensure the optic scanner is able to successfully locate these marks. You will note that the marks have a ▇▇▇▇ ▇▇▇▇ fill around them. This ▇▇▇▇ ▇▇▇▇ fill indicates that print information cannot be contained in this area in order for the optic scanner to operate properly.

REGISTRATION MARKS. The original Silhouette, Silhouette SD, CAMEO, and Portrait models have an optic scanner for reading marks that can be printed by Silhouette Studio®. These marks are called Registration Marks. These marks will print around the border of your workspace and will be read by the Silhouette’s optic scanner prior to cutting so that the Silhouette can triangulate according to where these marks are located and know exactly where the cut lines are defined around your printed images. Registration marks are only used when printing images for the purpose of performing print & cut jobs. To access these marks, click on the Registration Marks icon. You may enable the registration marks by clicking on the Show Reg Marks check box. If desired according to the job being performed, these marks can be adjusted. Please note that while you may make the marks smaller, if the Silhouette fails to locate these marks, you may need to adjust the registration ▇▇▇▇ mark size to ensure the optic scanner is able to successfully locate these marks. You will note that the marks have a ▇▇▇▇ ▇▇▇▇ fill around them. This ▇▇▇▇ ▇▇▇▇ fill indicates that print information cannot be contained in this area in order for the optic scanner to operate properly.