Railings. Translucent Skylights and Curtainwall Systems (i.e. Kalwall). • BIPV Glass (Building Integrated Photovoltaic). Included with the above listed items is the installation of all necessary hardware, trim, molding, caulk, mastic, gaskets and putty to properly complete the installation. In the event the EMPLOYER exclusively assigns work under this Agreement to the COUNCIL, the COUNCIL shall be notified of such assignment within sixty (60) days, or as soon as practical of the commencement of such assignment. In turn, the COUNCIL shall assure the EMPLOYER that other trades shall not interfere with such assignment. In the event an adjustment in such an assignment results in requiring the EMPLOYER to adjust the assignment by employing a composite crew, the EMPLOYER shall receive work rule considerations in order to compensate for increased labor costs. In case of composite crews, Glaziers will permit other trades who are members of a composite crew to perform all required work on the job. However, the setting of glass shall be the exclusive right of the xxxxxxx.
Railings. Dust handrails, stair stringers, risers and railings; wash as necessary.
Railings. Deck edge railing shall be provided around the entire deck perimeter. The railing shall be three tier, with maximum spacing between the tiers of 9 inches, 15 inches and 15 inches in accordance with EM385-1-1. Note that the lowest tier of railing can be omitted in way of deck fittings per EM385-1-1. The deck edge railing shall incorporate two entrance swing sections, 36 inches in clear width, one each port and starboard near the xxxxx.
Railings. The pulpit rails of the boats shall be made of SS 316 grade SS 316 grab rails of at least 2.5” protruding about 6” from the body of the boat shall be provided in the inside and outside of the entry/exit both on the port and starboard side of the boat. The grab rails may be terminated 2 feet above the deck level.
Railings. The height of rail or bulwark above the deck is about 1100 mm around the hull. Stanchions and wire ropes or chains are arranged in a way of bollards and where necessary but only in limited length. This information is confidential and proprietary to Wärtsilä. Page: 62 of 81 Project name: Project number: Quotation number: Created by: Document Id: Document creation date: Power Supply Upgrade. LGL P0900329 Q0900869 MNO002 August 25, 2009 Drain Plugs Drain plugs of stainless steel are provided to all tanks to the lowest point with clear markings. Lifting Eyes Lifting eyes are provided above all heavy equipment and elsewhere where necessary.
Railings. In accordance with EM 385-1-1, a Type C, 5 tier non-tensioned railing system shall be provided around the perimeter of the main deck as shown on the contract drawings. All stanchions shall be removable. Each stanchion shall be pinned to a socket above the deck. All chain shall be hot dipped galvanized and the hardware shall be stainless steel. The pins and retainers for the stanchions shall be stainless steel. On top of the deckhouses a Type A two tier rigid handrail system with toeboard shall be provided around the perimeter as shown on the contract drawings. In way of the ladder opening two safety chains shall be installed. All chain shall be hot dipped galvanized and the hardware shall be stainless steel.
Railings. A. Interior staircase railing: Railings hall be of M.S. structure and wooden handrail or as directed by architect. The M.S. structure will be finished off with 2 coats of oil paint over primer and the handrail will be polished.
Railings. A standard railing used to protect employees from falls shall consist of top rail, intermediate rail, toe board, and posts, and have a vertical height of 42 inches from upper surface of top rail to the floor, platform etc. • The top of a railing shall be smooth-surfaced, with strength to withstand at least 200 pounds. The intermediate rail shall be approximately halfway between the top rail and floor. • A stair railing shall be of construction similar to a standard railing, but the vertical height shall be no more than 34 inches, or less than 30 inches from upper surface of top rail to surface of tread in line with face or riser at forward edge of tread.
Railings. Detail will show typical panel and post arrangement giving details of post and panel steel sizes, height above ground/wall embedded post depth, ground centres, post centres, vertical bar spacings and end gaps at post. Gates Detail will show gate post sections, gate frame sections, gate infill details, gaps at hinge/post, hinge configuration, clear opening dimensions, (in the case of railing gates infills will be shown as railing panels, details stated above). These drawings will be shown in elevation and plan view and will be submitted within (stated period of time). Unless stated at pricing tender stage to NK Fencing Ltd, drawings for the above and for site layouts and setting out layouts will be charged to the Main Contractor/Client at a rate of £35.00 per hour or €50.00 per hour to produce. Manufacture drawing will not be submitted for approval/information unless stated to NK Fencing at pricing/tender stage.
Railings is also scheduled to “replace all first floor exterior walkway railings in Lodging Unit 1 (FMSS 10190) and Building (FMSS 94613) to meet safety codes.” NPS has noted that the project is eligible for use of RMR funds. However, based on our review, railings are also typically considered to be “fixtures” which are affixed to a building. The case law we have located shows that standard railings which are not specifically needed for a particular business operation (and thus “trade fixtures”) but instead are for simple safe use of the building are considered fixtures. In re Xxxxxx, 328 Fed. Appx. 833 (3d Cir. 2009)(railing bolted to floor of a motel bar was a fixture); Xxxxxxxx Wrecking Co. x. Xxxxxxxxxx, 93 Misc. 530 (S. Ct., 1st Dept., N.Y. 1916)(railing is a fixture).
