Product Characteristics. The Buyer represents that it has the requisite expertise, facilities and equipment to properly store, test, use and dispose of the Products. The Buyer and all its employees and others that handle the Products shall familiarize itself with the characteristics of the Products and shall comply with all laws, regulations, and standards applicable to the possession, handling, processing or use of the Products. The Buyer shall follow the safety recommendations of the Company provided that, notwithstanding any product instructions given by the Company, the Buyer shall be responsible to ensure that the Products shall be stored, tested, used, sold and/or disposed of strictly in compliance with instruction of the Company and any applicable health, safety, environmental, land use or other guidelines, standards, laws or regulations.
Product Characteristics. (a) SuperGen shall not be obligated to accept from AVI any Finished Product with less than the greater of (i) seventy-five percent (75%) of approved shelf life for such Finished Product or (ii) thirteen (13) months of remaining shelf life.
Product Characteristics. The Buyer represents that it has the requisite expertise, facilities and equipment to properly store, test, use and dispose of the Products. The Buyer and all its employees and others that handle the Products shall familiarize itself with the characteristics of the Products and shall comply with all laws, regulations, and standards applicable to the possession, handling, processing or use of the Products. The Buyer shall follow any safety recommendations or product instructions given by the Company, save that, notwithstanding any such recommendations or product instructions given by the Company, the Buyer shall be solely responsible to ensure that the Products are stored, tested, used, sold and/or disposed of strictly in compliance with any applicable health, safety, environmental, land use or other guidelines, standards, laws and/or regulations.
Product Characteristics. Supplier guarantees that Products and their packaging: (i) will be of new material, good quality and workmanship, and free from defects; (ii) will not impart any unintended flavor, odor, or color to any Buyer finished product; (iii) will conform to all applicable laws and regulations; (iv) will conform to all samples approved by Buyer and all previous shipments of Products in accordance with this Agreement; (v) will conform to warranties arising from our course of performance, course of dealing, or usage of trade; and (vi) will not, to Supplier’s knowledge, cause exposure to any chemical determined under the California Safe Drinking Water and Toxic Enforcement Act of 1986 and its regulations and amendments to cause cancer or reproductive toxicity.
Product Characteristics. The Buyer represents that it has the requisite expertise, facilities and equipment to properly unload, take delivery of, store, test, use and dispose of the Products. The Buyer and all its employees and agents that handle the Products shall familiarize themselves with the characteristics of the Products and shall comply with all laws, regulations, and standards applicable to the unloading, taking delivery of, possession, handling, processing or use of the Products. The Buyer shall follow the safety recommendations of the Company provided that, notwithstanding any product instructions given by the Company, the Buyer shall be responsible to ensure that the Products shall be unloaded, offtaken, stored, tested, used, sold and/or disposed of strictly in compliance with instruction of the Company and any applicable law, regulation and standard.
Product Characteristics. 11.1 The nature of our Product requires the Customer to take particular care when installing or using them. The Customer is responsible for ensuring that goods are suitable for their intended purpose and no warranty condition or representation is given by Fluidvalves as to the fitness of the goods for any particular purpose other than what is expressly stated on the Product Sheet. The goods are sold on the express understanding that the Products can be correctly handled in order to maximise the performance and significantly increase the lifespan of your Product. All Products must be maintained and regularly inspected for correct operation. All fluids used must be clean and conform to appropriate ISO/International standards. All Products must be installed in accordance with the installation and operating procedure.
Product Characteristics. Full Color on Every Pixel LightCaster™ miniature displays are the first to offer both high resolution and full color on every pixel, implementing sequential color techniques. Sequential color means that each pixel on the display is illuminated with the proper mix of red, green, and blue colors in fast enough succession for the human eye to fuse the sequence into a single, smooth color picture. Sequential color requires the fast (microsecond) switching speed of FLC materials. Other active matrix liquid crystals are made with slower nematic liquid crystals (NLCs). These more conventional AMLCDs employ triads of sub-pixels, which spatially separate red, green, and blue sub-pixels. This difference is especially noticeable when displays are physically small. LightCaster technology creates a much smoother (less grainy) color image than triad displays, even at the same resolution. With one third fewer pixels, our LightCaster display panels can also be made smaller, permitting a greater degree of product miniaturization and inherently lower production costs. High Resolution With LightCaster displays, pixel size and display resolutions are determined by the design of the VLSI backplane. For this reason, Displaytech can offer significant flexibility in OEM product specifications. For the cost of a new backplane design and a CMOS production run, displays can be produced with customer-specified resolution and pixel pitch, without significantly altering the downstream production process. VLSI backplanes are fabricated for high resolutions with extremely small pixels. Displaytech has successfully demonstrated pixels as small as 5.7 microns (4500 dpi), and has demonstrated fully operational SXGA (1280 × 1024) panels with 7.6-micron pixels (3300 dpi). Competing liquid crystal technologies use much thicker LC layers, causing lateral electric field cross talk, even with much larger pixels. This cross-talk problem limits usable small panel resolution. Production Ease/Competitive Cost Production costs of miniature displays are dominated by the cost of the active matrix backplane. Our LightCaster Display backplane is an integrated circuit produced using standard CMOS processing in a commercial foundry. By itself, this fact assures us of lower unit and capital costs, when compared to the competition. Additionally, the small die size further increases this advantage. Integrated circuit costs rise dramatically as chip size increases, for very understandable reasons. First, chips ...
Product Characteristics. The Buyer can read the essential characteristics of the goods offered for sale by XXXXX XXXX on the Website. XXXXX XXXX puts a lot of care into the images of the products it provides on the Website. However, due to the digital image processing and in spite of all the care that goes into those images, the sizes and/or colors and/or packaging of products may be slightly different from the reality. These images are for illustration purposes only and in case of a difference between the image and the description on the product sheet, the description on the product sheet shall be binding.
Product Characteristics. The subject product is a combination of a foreign currency time deposit and a foreign currency option. When the Customer invests in the subject product, the Customer invests in a foreign currency time deposit and sells a foreign currency option in the international foreign exchange market. On the Fixing Day/ Time, the Bank shall, in accordance with the Conversion Rate set forth by the Customer when investing in the subject product, determine if the Customer shall perform the obligation under the foreign currency option and decide whether the Payment Currency shall be the Base Currency or the Linked Currency. On the Maturity Date, the Bank shall calculate Customer's Principal Amount and the DCI All-In Interest, and make the payment in the currency determined on the Fixing Date as the Payment Currency. On the Maturity Day, the Bank shall automatically deposit the Principal Amount and DCI All-In Interest in the Payment Currency into Customer's multi-currency demand deposit account.
Product Characteristics. Neos shall have no obligation even to reasonably consider a proposed product as a Product unless such Product
