Common use of Measurement method Clause in Contracts

Measurement method. The isolation resistance measurement shall be conducted by selecting an appropriate measurement method from among those listed in paragraphs 2.1. through 2.2. of this annex, depending on the electrical charge of the live parts or the isolation resistance, etc. The range of the electrical circuit to be measured shall be clarified in advance, using electrical circuit diagrams, etc. Moreover, modification necessary for measuring the isolation resistance may be carried out, such as removal of the cover in order to reach the live parts, drawing of measurement lines, change in software, etc. In cases where the measured values are not stable due to the operation of the on-board isolation resistance monitoring system, etc., necessary modification for conducting the measurement may be carried out, such as stopping of the operation of the device concerned or removing it. Furthermore, when the device is removed, it shall be proven, using drawings, etc., that it will not change the isolation resistance between the live parts and the electrical chassis. Utmost care shall be exercised as to short circuit, electric shock, etc., for this confirmation might require direct operations of the high-voltage circuit. 2.1. Measurement method using voltage from off-vehicle sources 2.1.1. Measurement instrument An isolation resistance test instrument capable of applying a DC voltage higher than the working voltage of the high voltage bus shall be used.

Measurement method. The isolation resistance measurement shall be conducted by selecting an appropriate measurement method from among those listed in paragraphs 2.1. through 2.2. of this annex, depending on the electrical charge of the live parts or the isolation resistance, etc. The range of the electrical circuit to be measured shall be clarified in advance, using electrical circuit diagrams, etc. Moreover, modification necessary for measuring the isolation resistance may be carried out, such as removal of the cover in order to reach the live parts, drawing of measurement lines, change in software, etc. Public Comment Only In cases where the measured values are not stable due to the operation of the on-board isolation resistance monitoring system, etc., necessary modification for conducting the measurement may be carried out, such as stopping of the operation of the device concerned or removing it. Furthermore, when the device is removed, it shall be proven, using drawings, etc., that it will not change the isolation resistance between the live parts and the electrical chassis. Utmost care shall be exercised as to short circuit, electric shock, etc., for this confirmation might require direct operations of the high-voltage circuit. 2.1. Measurement method using voltage from off-vehicle sources 2.1.1. Measurement instrument An isolation resistance test instrument capable of applying a DC voltage higher than the working voltage of the high voltage bus shall be used.

Measurement method. The isolation resistance measurement shall be conducted by selecting an appropriate measurement method from among those listed in paragraphs Paragraphs 2.1. through 2.2. of this annex., depending on the electrical charge of the live parts or the isolation resistance, etc. The range of the electrical circuit to be measured shall be clarified in advance, using electrical circuit diagrams, etc. Moreover, modification necessary for measuring the isolation resistance may be carried out, such as removal of the cover in order to reach the live parts, drawing of measurement lines, change in software, etc. In cases where the measured values are not stable due to the operation of the on-board isolation resistance monitoring system, etc., necessary modification for conducting the measurement may be carried out, such as stopping of the operation of the device concerned or removing it. Furthermore, when the device is removed, it shall be proven, using drawings, etc., that it will not change the isolation resistance between the live parts and the electrical chassis. Utmost care shall be exercised as to short circuit, electric shock, etc., for this confirmation might require direct operations of the high-voltage circuit. 2.1. Measurement method using voltage from off-vehicle sources 2.1.1. Measurement instrument An isolation resistance test instrument capable of applying a DC voltage higher than the working voltage of the high voltage bus shall be used.

Measurement method. The isolation resistance measurement shall be conducted by selecting an appropriate measurement method from among those listed in paragraphs 2.1. through 2.2. of this annex., depending on the electrical charge of the live parts or the isolation resistance, etc. The range of the electrical circuit to be measured shall be clarified in advance, using electrical circuit diagrams, etc. Moreover, modification necessary for measuring the isolation resistance may be carried out, such as removal of the cover in order to reach the live parts, drawing of measurement lines, change in software, etc. In cases where the measured values are not stable due to the operation of the on-board isolation resistance monitoring system, etc., necessary modification for conducting the measurement may be carried out, such as stopping of the operation of the device concerned or removing it. Furthermore, when the device is removed, it shall be proven, using drawings, etc., that it will not change the isolation resistance between the live parts and the electrical chassis. Utmost care shall be exercised as to short circuit, electric shock, etc., for this confirmation might require direct operations of the high-voltage circuit. 2.1. Measurement method using DC voltage from off-vehicle sources 2.1.1. Measurement instrument An isolation resistance test instrument capable of applying a DC voltage higher than the working voltage of the high voltage bus shall be used.