Lisvane Old School. Community Centre incorporated and registered with the Charity Commission with number 1156308 of 0 Xxxxxx Xxxxxxx Xxxx, Xxxxxxx, Xxxxxxx XX00 0XX (Developer);and
High School The District shall continue with its current practices to provide a continuous, uninterrupted preparation period during the school day.
Middle School The teacher’s day shall be six (6) hours and fifty (50) minutes excluding time set aside for duty free lunch. Except on half days, each teacher shall have five (5) assigned periods each school day, and one unassigned period of fifty five (55) minutes duration. Each teacher shall have a Silent Sustained Reading (SSR) period of 18 minutes. It is understood that each teacher shall be in his/her building at least eight (8) minutes prior to the start of his/her assignment and, in order to ensure the proper supervision and safety of students, shall be at his/her place of assignment at least five (5) minutes prior to the start of such assignment. Each teacher shall remain in the building at five (5) minutes after the completion of his/her assignment.
Summer School The Appointing Authority shall notify all supervisors of all summer school openings. A supervisor may agree to voluntarily remain on layoff in the event of a recall by requesting such action through a written waiver mutually agreed to and signed by the Appointing Authority and the supervisor. Once the supervisor elects to sign the waiver of recall, such supervisor shall not be able to exercise his/her seniority rights for recall for the duration of the summer school. The Appointing Authority agrees to provide a signed copy of any waiver of recall to both the Association and the supervisor. Any waiver of recall by a supervisor is not to be considered a refusal to return to work and shall not be considered to be a break in continuous service. This section does not, in any way, constitute a forfeiture of the Appointing Authority's right to recall laid off supervisors, whenever necessary, to carry out the functions and needs of the summer school programs. Notification of intent to return to work may be made in writing and hand delivered, provided that a written receipt of such notification is given.
Millwright Shall be qualified to assist and work under the direction and instructions of Millwright I or A. He will work alone at times performing assignments in keeping with his training. He must become proficient in good practices in the areas of fitting, aligning, lubricating and the operation of all shop tools and machines. In addition to the foregoing, he will be exposed to basic principles of hydraulics and pneumatics. He will begin the process of learn- ing techniques required in trouble shooting key production machinery, pipefitting, and basic welding, but will not be expected to display a high degree of proficiency in these areas at this point. He will be required to have the necessary tools to perform his duties. Under direction, will continue to develop skills in trouble shooting all plant equipment. Millwright Must be capable of performing the tasks of fitting, aligning, and able to operate all shop tools and machines. Must, under direction, become proficient in basic welding and pipe-fitting as well as dismantling and reassembly of plant He may work alone frequently, but occasionally will require direc- tion and instructions from Millwright I, or A. Must, under direction, become proficient at effective methods of trouble shooting and repairing hydraulic, pneumatic and mechan- ical faults in plant machinery. Millwright Must be capable, without direction, of fitting, aligning, lubricating, taking apart and reassembling plant equipment. In addition, is expected to be to weld, operate shop tools and do pipefitting as required. Under direction will begin the process of learning machining and continue to improve his skills at machining parts. Millwright I Must be capable, without direction, of performing all practices under Millwright Must under direction, become proficient at reading and understanding blueprints, all phases of installing new equipment, laying out hydraulic and mechanical drives and meet speed and power requirements correctly. Millwright A Must be capable, without direction, of performing all practices under Millwright I, and Must take full responsibility for work done by himself or his assistant. Must be in possession of a Millwright Certificate or a Machinist Certificate or Welder Certificate. Must be in possession of a ProvincialTrades Certificate recognized by the Ontario Ministry of Labour. Filer Trainee Trains on saw and knife changes and knife grinding Filer C He shall be capable under direction of performing all changes and knife grinding. Filer B He shall be capable under direction of performing all changes and knife grinding bench, fitting and sharpening saws. Filer A He shall be capable without direction of performing all jobs listed under
NO HARDSTOP/PASSIVE LICENSE MONITORING Unless an Authorized User is otherwise specifically advised to the contrary in writing at the time of order and prior to purchase, Contractor hereby warrants and represents that the Product and all Upgrades do not and will not contain any computer code that would disable the Product or Upgrades or impair in any way its operation based on the elapsing of a period of time, exceeding an authorized number of copies, advancement to a particular date or other numeral, or other similar self-destruct mechanisms (sometimes referred to as “time bombs,” “time locks,” or “drop dead” devices) or that would permit Contractor to access the Product to cause such disablement or impairment (sometimes referred to as a “trap door” device). Contractor agrees that in the event of a breach or alleged breach of this provision that Authorized User shall not have an adequate remedy at law, including monetary damages, and that Authorized User shall consequently be entitled to seek a temporary restraining order, injunction, or other form of equitable relief against the continuance of such breach, in addition to any and all remedies to which Authorized User shall be entitled.
MODERN SLAVERY You hereby affirm your compliance with the Modern Slavery Xxx 0000 and associated guidance. You confirm (a) that you have read, are familiar with and shall not perform an act or omission which is in contravention with, the letter or spirit of the Act; and (b) you carry out regular, meaningful and comprehensive due diligence procedures and have internal policies in place to address any suspected human rights abuse in your business and Group where applicable.
MIDDLE SCHOOLS 1. Where there are no negotiated provisions concerning the implementation or operation of a middle school program, this article shall govern the implementation or operation of a middle school program in a school district.
Manufacturing Technology Transfer In addition to the Licensed Know-How provided to Company pursuant to the Technology Transfer, upon Company’s written request, Asana will promptly prepare and submit to the JSC, for its review and approval, a plan for the transfer to Company of all Know-How Controlled by Asana with respect to the manufacture of Licensed Compounds and Licensed Products, and the conduct by Asana of such consultation activities, as are necessary to enable Company or a Third Party contract manufacturing organization to manufacture for the Territory (i) Licensed Compounds or (ii) Licensed Products (such plan, the “Manufacturing Technology Transfer Plan” and such actions, the “Manufacturing Technology Transfer”). Following the review and approval by the JSC of the Manufacturing Technology Transfer Plan, Asana will perform (or cause one or more applicable Third Parties (including, as applicable, any CMO engaged by Asana to manufacture Licensed Compounds or Licensed Products) to perform) a single Manufacturing Technology Transfer in accordance with such Manufacturing Technology Transfer Plan to Company or a Third Party CMO at Asana’s expense. Asana will make employees or agents of Asana available to Company for up to twenty (20) hours, in the aggregate, at no additional cost to Company, to facilitate the Manufacturing Technology Transfer. Asana will initiate the Manufacturing Technology Transfer promptly following the approval by the JSC of the Manufacturing Technology Transfer Plan. After completion of the Manufacturing Technology Transfer to a facility, use of such facility to manufacture Licensed Compounds or Licensed Products shall be subject to successful completion of any necessary inspections required by applicable Regulatory Authorities (collectively, the “Qualifying Audits”). All Licensed Compounds and Licensed Products manufactured by or on behalf of Company or its CMO shall be manufactured in compliance with all Applicable Laws and applicable specifications therefor.
Xxxxx, Haldimand, Norfolk The approved posted schedule shall provide a minimum of 16 hours off between scheduled tours, unless mutually agreed between the Nurse and the team.
University Any notice may be served upon the University by delivering it, in writing, to the University at the address set forth on the last page of this Agreement, by depositing it in a United States Postal Service deposit box with the postage fully prepaid and with the notice addressed to the University at the aforementioned address, or by sending a facsimile of it to the University facsimile number set forth on the last page of this Agreement.