Common use of Fittings Clause in Contracts

Fittings. 1.7.3.1. The supports shall be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conductive to the collection of water. 1.7.3.2. The base of the container shall be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base shall give the container sufficient stability. The top edge of the base shall be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates shall be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures shall be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports shall must be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conductive conducive to the collection of water. 1.7.3.2. The base of the container shall must be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base shall must give the container sufficient stability. The top edge of the base shall must be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates shall must be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures shall must be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports shall must be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conductive conducive to the collection of water. 1.7.3.2. The base of the container shall must be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base shall must give the container sufficient stability. The top edge of the base shall must be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark ▇▇▇▇ shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates shall must be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures shall must be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports shall be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conductive to the collection of water. 1.7.3.2. The base of the container shall be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base shall give the container sufficient stability. The top edge of the base shall be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark ▇▇▇▇ shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates shall be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures shall be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.