Electrical Components. The electrical components are warranted for one (1) year and include, but are not limited to, the circulation blower, snap disc thermostat, power cord, and three-speed switch. What is covered by this warranty? This warranty covers any defects in materials or workmanship in your new ENERGY KING solid-fuel heating appliance. What is not covered by this warranty? This limited warranty does not apply: ▪ If your appliance has not been installed, operated and maintained in strict accordance with instructions provided in the Installation, Operation and Maintenance Manual. ▪ If any part has been damaged in shipment, modified, altered, tampered with, abused, or has been subject to accident or misuse. ▪ If your appliance has been altered or repaired in a manner which, in our sole judgment, affects its performance, stability or reliability. ▪ If parts not made or supplied by us have been used in connection with the appliance, if in our sole judgment, such use affects its performance, stability or reliability. ▪ To transportation charges on appliances and appliance parts submitted for repair or replacement under this warranty. ▪ To expendable, replaceable or wear items, such as firebrick, gaskets/seals, paint, handles and other items that in our judgment are expendable, replaceable or wear items. ▪ To any heating system or systems to which the appliance may be attached. ▪ To any of the smoke pipes, heat pipes, chimney, hardware, ducting, vents, or other accessories used for the installation and venting or ducting of the appliance. We are not responsible for installation and will not be liable in any respect under the terms of the warranty for injury or damage to the building structure in which the appliance has been installed, or to the person or persons and property therein, arising out of the use, or installation of the ENERGY KING appliance. The appliance must be installed in compliance with the local, state and national building and fire codes and regulations of the area and in strict adherence to the Manufacturer’s recommendations. What will we do to correct problems? We will repair, or at our option, replace any ENERGY KING solid-fuel heating appliance or appliance part, which upon inspection shows a defect in materials or workmanship. Rev 05/10/10 ENERGY KING Bay 2000C Owner’s Manual ◆ U. S. Warranty Page 1 of 2 How can you get service? If warranty service is needed during the warranty period, notify your authorized ENERGY KING dealer. If there is no ENERGY KIN...
Electrical Components. All electrical components of the Wind Farm shall conform to relevant, applicable, and adopted local, state, and national codes.
Electrical Components. Alternator/stator, starter, starter solenoid, voltage regulator, rectifier, ignition coil, switch box, ignition module, trigger and sensor, windshield wiper motor. Wiring/wiring harness is covered only as the result of a Mechanical Breakdown of a covered component.
Electrical Components. Alternator/Generator; Ignition Module; Ignition Switch; Headlight Switch; Turn Signal Switch; Horns; Distributor (does not include Cap and Rotor); Starter Motor; Starter Solenoid; Starter Drive;
Electrical Components. All electrical components of the Project Facilities shall conform to relevant and applicable state and national codes, and relevant and applicable international standards.
Electrical Components. 1. Upgraded Energy Star Qualified ceiling fixtures in all bedrooms, hallways, side halls, foyer, kitchen, breakfast room, den, living room, dining room, and family room / great room. Bathrooms to receive a wall mounted light fixture over the vanity and ceiling fixture (excluding powder room).
Electrical Components. Alternator; starter; manually operated switches; coils; rectifiers; magneto; voltage regulator; electronic ignition control modules; electronic fuel injection control module and sensors; wiring harness; and cooling fan motor.
Electrical Components. All electrical manual switches, alternator, analog gauges, cam sensor, ignition module, Engine Control Unit (ECU), engine control module (ECM), map sensor, mass airflow sensor, power door lock actuators, starter drive, starter motor, starter solenoid, and voltage regulator. AIR CONDITIONING & HEATING (Factory Authorized Only): Accumulator, compressor, compressor clutch, compressor pulley, condenser, evaporator, expansion valve, high/low cut off switches, orifice tube, and receiver/dryer. FRONT & REAR SUSPENSION: Ball joints, struts, spindles, upper and lower control arms, and wheel bearings. FUEL SYSTEM: Fuel injection pump, metal fuel lines, and primary fuel pump. COOLING SYSTEM: Blower motor, cooling fan clutch, cooling fan blade, cooling fan motor, heater core, radiator, and water pump. SEALS & GASKETS*: On all listed components, including: Axle gasket(s), compressor seal(s), CV joint boot(s), cylinder head gasket(s), differential gasket(s), exhaust manifold gasket(s), front crankshaft seal(s), hub or wheel bearing seals, intake manifold gasket(s), oil pan gasket, output shaft seal, rear main seal, shifter seal, speedometer cable seal, steering pump shaft seal, timing cover gasket, transfer case seal(s), transmission pan gasket, valve cover gasket.
Electrical Components. The electrical components in the luminaire shall include an electronic dimmable LED power driver, 10 KA surge protection, low voltage indicator device and terminal board with pressure type terminals, all to be prewired and tested at the point of manufacture. The LED dimmable LED power driver shall be 120– 277 Volt, 50/60 HZ class I for 110 watt luminaire or Class I or II for 78 watt luminaire, with power Factor more than 90% and THD less than 20% of full load. Integral weather-tight electrical box for easy power hook-up, dimmable LED power driver shall be IP65 rated minimum. Voltage dips up to 30% below the nominal line volts of 120 shall not affect LED board power or cause luminaire to dim or fail. The terminal board shall be equipped with four (4) clamp-type pressure terminals for connection to the phase leg, neutral, ground of the primary circuit and a controlled phase connection for another luminaire. The terminals shall be properly identified for connection, with notations on terminal board, color coding, or wiring diagram. The whole luminaire assembly shall be completely prewired requiring only the connection of the primary circuit wires for its operation. Wiring shall be #16 stranded wires, with silicone rubber insulation, fiberglass sheath and lacquer finish, or cross-linked polyethylene insulation of 105o Centigrade rating. LOW VOLTAGE INDICATOR LAMP
Electrical Components. 1. Traffic signal section wiring shall conform to ANSI Standard D-10.1.
